Cisco Switching/Routing :: 6509 - Cannot Find Reference To Error
Mar 5, 2010This is a 6509 with Sup-2/MSFC2. Can't find any reference to this error on the cisco web site.
View 2 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Getting Error Logs In 6509?
Feb 3, 2012%SYSTEM_CONTROLLER-SP-3-ERROR: Error condition detected: TM_DATA_PARITY_ERROR Feb 2 10:57:09.602 EST: %SYSTEM_CONTROLLER-SP-3-EXCESSIVE_RESET: System Controller is getting reset so frequently
Cisco Internetwork Operating System Software
IOS (tm) s222_rp Software (s222_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF15a, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 20-Oct-08 19:20 by kellythw
Image text-base: 0x40101040, data-base: 0x42951080
[code]....
Cisco Switching/Routing :: Cat 6509 - VSS - Minor Error (Sup Module)
Mar 17, 2012We have a VSS environment with two Cisco 6509-Es. IOS image:s72033-ipservicesk9_wan-mz.122-33.SXI5 when I switch on or reload the Core switches(VSS), I find a Minor Error in the "Show module switch all" command.I also did a "show diagnostic result switch 1 module 5"Switch 1 Module 5: Supervisor Engine 720 10GE (Active) SerialNo : SAL1521E035
Overall Diagnostic Result for Switch 1 Module 5 : MINOR ERROR
Diagnostic level at card bootup: complete
Test results: (. = Pass, F = Fail, U = Untested)
45) TestVslLocalLoopback:
Port 1 2 3 4 5
-------------------
U U U . F
This issue temporarily relieves when reseating the X2 module, but reappears after reloading the switch.
Cisco Switching/Routing :: 3745 Router Failed To Exchange The Reference Signal
Mar 17, 2013I am almost new to the networking field, hence I might have lacking some basic knowledge. I like to know the impact if the ground of any router get disconnect. WIll the router stops work? We have two peripheral router in my organization, both are connect with the MPLS cloud through the MUX. One router (3745) have ground connection, where as the other (3845) don't. Recently the 3745 router start generating CRC error on the WAN interface. Once we remove the patch cord connecting with the MUX for loop test and reconnect later, the interface did not come back again. FInaly someone advice me to check the ground connection. I found it was loose. Once I fix it properly and reboot the router the interface become up. The person told me that some cisco router send the reference signal through the ground to the MUX connecting with it, if the MUX and router failed to exchange the reference signal the router will not work, is this true ?
View 2 Replies View RelatedCisco Switching/Routing :: Cat 6500 - IOS 12.2(33)SXJ5 Version Of Reference Site Inquiry
Jun 8, 2013We prepare to upgrade the IOS and reviewing the 12.2(33)SXJ5 version. IOS 12.2(33)SXJ5 version of the reference site inquiry.
View 5 Replies View RelatedCisco Switching/Routing :: Find Out Who Made Last Configuration Change On CAT 6509
Jul 16, 2012How do I find out who made the last configuration change on a 6509 CAT switch with the following Show VER
WS-C6509 Software, Version NmpSW: 8.5(9)
Copyright (c) 1995-2007 by Cisco Systems
NMP S/W compiled on Apr 16 2007, 21:23:23
[Code].....
Cisco Switching/Routing :: 6509 / Mac Address Error Message No Entries Present
Dec 6, 2012I am receiving this error after connecting a copper adapter on a GBIC blade in a 6509. Here are the results from the show Interface. I am waiting to confirm the device on the other side settings but as far as I see I get UP and Up for protocol and line respectively.
GigabitEthernet2/11 is up, line protocol is up (connected)
Hardware is C6k 1000Mb 802.3, address is 0009.11e4.f3ce (bia 0009.11e4.f3ce)
Description: RCPBSDEV
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
[code]....
Cisco Switching/Routing :: 6509 - Fabric In Slot 5 Reported Timeout Error For Channel 11
Apr 27, 2013There is a cisco ws-c6509,recently it appear error log “%FABRIC-SP-6-TIMEOUT_ERR: Fabric in slot 5 reported timeout error for channel 11 (Module 3, fabric connection 1)”. When I reload the device,the error log disappear.But a few days later,it appears again.I try to replace the slot 3 (WS-X6704-10GE),the error log continues.The IOS version is 's72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF8"
View 1 Replies View RelatedCisco Switching/Routing :: 2811 - Error Unable To Find Entry For VLAN (1)
Aug 23, 2009Aug 24 11:32:16.275 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to down
Aug 24 11:32:36.827 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan21, changed state to up
Aug 24 11:35:23.854 AEST: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1/2, changed state to down
Aug 24 11:35:24.854 AEST: %LINK-3-UPDOWN: Interface FastEthernet0/1/2, changed state to downesw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)
esw_mrvl_vlan_port_remove : Unable to find entry for VLAN(1) dbnum(1)(code)
When the above problem happens, as work-around, we delete VLAN.DAT file on the Compact Flash of this 2811 router and recopy the VLAN>DAT file back to teh Compact Flash.
Then it runs for a few weeks and the same problem happened.
Then we put a new Compact Flash and recopied VLAN.DAT to new CF and it ran for 3 weeks and same problem started again.
Could be 2811 router motherboard? This customer has thousands of these 2811 routers in identical setups and this is the only router that is having this problem.
Cisco Switching/Routing :: 6509 To 6509-E Chassis Upgrade?
Nov 21, 2011I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Cisco Switching/Routing :: Upgrade Of 6509 To 6509-E Chassis
Nov 21, 2011I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Cisco Switching/Routing :: Input Error And CRC Error On Router 1841?
Mar 12, 2013The router 1841 is connected directly to the layer switch. the network diagram is below:
Office A --> Switch (L3) --> Router 1841 --> Internet --> Office B
However, when I transfer the file from Office A to office B, the speed very slow ( only around 40 kb/second), and there are an input error and CRC error:
Cisco-R1841#sh interfaces FA0/1
FastEthernet0/1 is up, line protocol is up
Hardware is Gt96k FE, address is 0019.e02f.03dd (bia 0019.e02f.03dd)
[Code]......
Cisco Switching/Routing :: 6509 / 4900 - Network Down Cause Switching Supervisor With Redundancy
Jan 11, 2012we've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies View RelatedCisco Switching/Routing :: 6509 - Upgrading Switching Infrastructure
Apr 11, 2012The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-
Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)
I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports
Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each
and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.
Cisco Switching/Routing :: Policy Routing Based On Client Gateway (6509-E)
Feb 26, 2012If client gateway = 192.168.64.9 then next-hop = 192.168.64.8 else use default-route 0.0.0.0
I know it's possible to do a route-map match ip-address ACL list. But is it possible to match on gateway?
Some info about hardware and config:
6509-E in VSS (IOS 12.2(17r)SX5) withVS-S720-10G supervisor.
All routes are static, IP for 192.168.64.9 is on SVI vlan.
Cisco Switching/Routing :: 6509 MSFC - LAN Default Gateway Routing
Mar 6, 2012I have two ISPs. Each is on it's own subnet connected to the 6509 MSFC/Switch. FW1 is on 100.1.100.0/30 and FW2 is on 200.1.200.0/30 subnet. My goal is route all traffice going to the Internet from subnet 10.133.3.0/24 to FW1 and all other subnets across the organization to FW2. I am not sure if I need to use ACL / Static route combo, or just a static routes or ACLS?
View 5 Replies View RelatedCisco Switching/Routing :: 6509 Use Policy Based Routing To Redirect Http Traffic
May 29, 2012We have a Catalyst 6509 switch, and we hope to use policy based routing to redirect http traffic to my proxy server, where I can find the configuration example?
View 11 Replies View RelatedCisco Switching/Routing :: 6509 - Inhibit Vlan Routing
Nov 8, 2012I would like to ask you if it's possibile to block routing between some Vlan for just once of them.
Maybe I can explain better:
I've got a Cisco 6509 with 4 configured vlan interfaces
Int Vlan 10 10.10.1.0/24
Int Vlan 20 10.10.2.0/24
Int Vlan 30 10.10.3.0/24
Int Vlan 40 10.10.4.0/24
Vlan "10" is the phone voip Vlan and it must not talk with the others Vlan. The others Vlan can comunicate normally except with Vlan "10".
Pratically Vlan "10" needs to be isolated from the others.
This equirement comes becouse Vlan 10 is wireless and has the WEP key encryption (very weak protocol). Some Phone couldn't support the WPA2 key and I need to avoid an unauthorized external client, cracking the WEP key and connecting to this WiFi, could have free access to the others Vlan.
Cisco Switching/Routing :: 6509 - Multicast Routing Preference
Nov 14, 2012I have a problem on my catalyst 6509 on which I would like to do the following things :
I have some Vlans in which multicast is enabled.
In tose Vlan theres is a router which is default router for equipements.
I had enabled multicast routing because some Vlan needs to exchange multicast informations, but I wolud like to make difference between Multicast traffic. For example I have 5 vlans:
Vlan 1 and 2 need to exchange Multicast informations but the don't need multicast information from Vlan 3 and 4
Vlan 3 and 5 need to exchange Multicast informations but the don't need multicast information from Vlan 1 and 2
Vlan 5 is independant Vlan but doesn't need to have multicast information from all others vlan.
Last problem, equipement on differents vlan can use the same Mulkticast group address. In this case, Multicast routing is not working between Vlan 1 to Vlan 2 and Vlan 3 to Vlan 4.
Cisco Switching/Routing :: Policy Based Routing On 6509
Mar 6, 2012I need to setup my 6509 with PBR going to two different Firewalls. The 6509 has vlans and multiple serial interfaces. What/where do I install the policy-maps? I want to direct one of the vlans to one firewall and the other vlans and wan subnets to the other firewall.
View 26 Replies View RelatedCisco Switching/Routing :: 6509 / Migrating From IOS To NX-OS
Aug 7, 2011I am migrating from Cisco 6509 IOS (12.2) to Nexus 7000 NX-OS (5.1(1)).I am looking for a equivalente NX-OS command for permit ipinip on IOS.
View 2 Replies View RelatedCisco Switching/Routing :: Getting Very High CPU In 6509?
Mar 3, 2012I have 2 6509-E chassis with SUP-720-VSS and classic line cards :-(. on October 2011 the switch reached 100% CPU on both devices and the entire network went down. Customer restarted the core so we lost all the log files and couldnt find out any root cause on the same. TAC engineer suggested to have some script configured on the system in case of CPU shooting up above 70%, it will create a file in flash and keep appending the logs to the same. Last week i got call from customer saying that the CPU again went high for around a minute on both the cores. Last time i added CoPP also on the switch in order to prevent the CPU reaching 100%. Still it went high and from the captured logs i saw that the process created the high CPU was Port Manager Per and SSH process. Attached the file created by the netdr capture command.
View 1 Replies View RelatedCisco Switching/Routing :: 6509 - VSS Using Just Three (3) Supervisors
Aug 3, 2012I have a customer that has a Catalyst 6509 with two Supervisor VSS capable and my Sales team sell another 6509 with just one Supervisor VSS capable. Simple question: Will VSS configuration will recognize that I have three Supervisors? It will work as QUAD-SUP solution or as a normal VSS solution?
View 7 Replies View RelatedCisco Switching/Routing :: SFP+ Supported On 6509-E?
Nov 16, 2011We are trying to migrate from 1g to 10G, couldn't find any module on 6509-E which supports 10G on SFP+ ...I can see X2 and Xenpacks .. but not SFP + .what exactly this Xenpack means ?
View 3 Replies View RelatedCisco Switching/Routing :: CAT 6509 STP Compatibility With F5 LTM
Sep 1, 2012We have connected a single F5 box with dual links to 2 different Cisco Catalyst switches using 802.1Q trunks. F5 is configured with RSTP mode and on Cisco Switch RPVST+ is configured.STP root bridge is hardcoded on the Cisco side. Loop Guard is globally enabled.On F5 STP link type is Auto, STP Edge port is disabled since that port is connected to the cisco switch.When we are failing over the F5 primary link to the secondary link we see 'Loop Inconsistent' on the cisco switch and things dont work after the failover.We have tried configuring the F5 as STP passthrough but that doesn't fix out the issue.I have checked out the forums and found out following recommendations
1. Configuring MSTP bw F5 and Cisco for better compatibility (Not possible from Cisco side because of a major change in large production setup)
2. Configuring VSS in Cisco switches (not possible due to hardware limitation)
3. Connecting F5 using single links to each switch (redundancy compromised)
I am wondering that on which default vlan does the F5 STP instance0 sends the STP BPDUs ? the term used on Cisco side is native vlan and others use PVIDs; that F5 default vlan should match the native vlan on cisco trunk side.
Cisco Switching/Routing :: Getting 6509 VSS IOS Upgrade?
May 15, 2012Tonight we were performing an IOS upgrade on our 6509 VSS to 122-33.SXI6. Both 6509's have dual Supervisor cards installed. Initially we had problems with switch 2 slot 5 supervisor returning to rommon however switch 2 slot 6 supervisor loaded correctly. After manually setting the boot var in rommon, switch 2 slot 5 supervisor reloaded correctly.
After all supervisor's were online we noticed when looking at " show switch virtual redundancy" that sw 1 & 2 slot 6 supervisors were running the correct IOS version but sw 1 & 2 slot 5 were running different IOS versions, however when looking at the show version we are running on the upgraded IOS??? See output below...
Why the active supervisor has loaded the incorrect IOS the VSS is running on the upgraded IOS? I have verified the IOS was copied correctly to each supervisor bootdisk, I see no issues.
My Switch Id = 1 Peer Switch Id = 2 Last switchover reason = none Configured Redundancy Mode = sso Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :----------------------------------------------- Current Software state = ACTIVE Uptime in current state = 3 hours, 38 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)Technical Support:
[code].....
Cisco Switching/Routing :: 6509 - NAT / DHCP
Nov 30, 2011We are looking to avoid the need to install an additional device in our network as our core 6509s are not being pushed by any stretch. However, we are having an issue getting the 6509 to assign DHCP addresses and perform NAT.
Most interfaces and V LAN's on the 6509 are using public IPs and have BGP routing at the edge. We have a trunk up link coming into the 6509 on a ws-6816 card via a SMF GBIC in slot 9, port 2 that feeds a wifi link where we are looking to provide guest access to our network.
We created 2 V LAN s on the switch 20 and 21. We assigned a private IP and network to the VLAN20 interface and assigned a new public /30 sub net ip to the V LAN 21 interface. The following configuration was applied which I thought was the required configuration based on how we would typically configure ISR routers for the same services...
ip dhcp excluded-address 10.200.200.1
!
ip dhcp pool WiFi_Pool
network 10.200.200.0 255.255.255.0
default-router 10.200.200.1
dns-server 4.2.2.1 4.2.2.2
[ code]...
What am I missing in this configuration? Note that if I create an access switch port for v LAN 20 on the switch and plug a laptop in directly to the 6509, the laptop is unable to receive a DHCP address. If I assign the laptop an address in the 10.200.200.0 /24 range manually, I can ping 10.200.200.1 from the laptop, however, the laptop will not get to the internet as it appears to be failing to perform nat.
Cisco Switching/Routing :: 6509 - VSS Implementation
Jun 5, 2011 I have a network with four 6509s in a ring with 10Gb links. Two adjacent switches are at the home office, the other two at the DR site. The switches at each location are physically similar to each other with respect to what blades are in them. We went through an upgrade from SUP-720's to VS-SUP-720's recently, only at the DR site - basically a practice, with the home office conversion hopefully taking place next weekend.
We initially just brought up the two chassis separately, in non-VSS formation (stand-alone). So far, so good - everything was connected, all traffic was passiing, all links were up, everything was reachable: EVERYTHING worked. Then we made the conversion: step-by-step from the cisco.com page; create a virtual domain, make one switch switch 1, the other switch 2, create differently numbered port-channels on each 6509, add the SUP 10Gb links to the port-channel, do the conversion.
Here's where the trouble started. First of all, the two 10Gb links back to home office created a spanning-tree loop and we had to shut down one of the links. (Is there something that needs to be configured on those links to turn spanning tree on? Does VSS conversion turn stp off?) Secondly, though it worked while in stand-alone mode, the copper blade in the standby 6509 stopped passing traffic - it would take config, the links would come up, but you could not ping across those links. Interestingly enough, there was an access switch with links to each of the copper blades, and having them both up also caused a spanning-tree loop. adding a new port-channel and putting both links in it did nothing to alleviate the loop. This leads me to believe that stp is not working properly. I reiterate, that even though the loop occurred, nothing else plugged into that blade was pingable.
Cisco Switching/Routing :: 6509 - VSS Between Sites?
Nov 9, 2011I have been asked to research running VSS between 2 6509's between 2 sites?
I am just going through the whitepapers and need to establish the link requirements for such a setup.
Is it a valid setup?
Cisco Switching/Routing :: 6509 VSS IOS Upgrade
Jan 15, 2012Will I be OK doing a eFSU Upgrade from s72033-ipservicesk9_wan-mz.122-33.SXI2a to s72033-ipservicesk9_wan-mz.122-33.SXJ1?
I only have a single supervisor in each chassis.
Should I be ok with just following the eFSU upgrade instructions in the below?
[URL]
Cisco Switching/Routing :: GBIC On 6509
Nov 7, 2011I have an interesting problem. I have a 6509 that I'm trying to swap the GBIC on. The switch is already using a GLC-SX-MM GBIC and it is up/up and passing traffic, but we are getting some errors and suspect it may be faulty.
I want to replace the GBIC with one of the identical model - a GLC-SX-MM. It was brand new, never been opened. When the new GBIC is plugged in the link light on the switch goes completely off (not amber) and the port goes into a down/down (not connect) state. There are no messages in the logs at all. It's like it doesn't even see it. If you plug the old GBIC back in then the link comes back up. I tried a different port with the same results.Thinking that the new GBIC may be faulty (even though it was brand new) I tried a second GLX-SX-MM, also new. That one does the same thing.
At that point I thought there might be a problem with that switch, so I tried the GBICs on the other 6509 in that pair. The other 6509 is running the same hardware and software. The GBICs will not work there either. If you move the old, suspected faulty GBIC from 6509-2 to 6509-1 then that it works.
The solution would seem to be that I have two faulty GBICs, but I'm having trouble persuading myself that I have two new ones, straight out of the package, that are both bad. Are there any other things to check on the switch? Here's the pertinent information:
switch#show ver
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI3, RELEASE SOFTWARE (fc2)
<snip>
cisco WS-C6509-E (R7000) processor (revision 1.3) with 458720K/65536K bytes of memory.
Processor board ID SMG1109N3BK
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
[code]...
Cisco Switching/Routing :: Show Version On VSS 6509?
Apr 7, 2013Is there a way I can check the version of each device on two Cisco 6509 if they are Virtually connected (VSS)? When I enter the command show version, it only shows one result, unlike show module, you have an option to choose which switch by entering 1 or 2.
View 3 Replies View RelatedCisco Switching/Routing :: IOS For Support Of OSPF And BGP In 6509-E
Sep 13, 2012If i look at the Feature Navigator , it says that IP Base Supports OSPF and EIGRP. But if i look at the Cisco Link it contradicts the Cisco Feature Navigator.
[URL]
if I have 6509-E with VSS-SUP720-10G and want to run OSPF and BGP on the Switch. What is the IOS i require? WIll IP Base Suffice or i need to take Advance or Enterprise Image.