Is there a way I can check the version of each device on two Cisco 6509 if they are Virtually connected (VSS)? When I enter the command show version, it only shows one result, unlike show module, you have an option to choose which switch by entering 1 or 2.
View 3 RepliesI change only a chasis in a router 3845, but the "show version" command should be the same , except for the serial number and other parameter of time.. however, the number of serial interface change from 4 up to 2.The hardware module of 3845 are 3.
1.- VWIC E1/T1 with 2 port
2.- Fastethernet 36 port
3.- Supervisor engine with 2 Gigabit port
Configuring FWSM in a 6509. When I set "firewall vlan-group 40 40-42,251", it results in: "No more than one svi is allowed. Command rejected.".
I had "firewall multiple-vlan-interfaces" set for a previous use of this module, but took that off with the "no" command. Suspect that is the issue, but do not see how to resolve. Seems similar to bug CSCsr48563, but I am at the fixed code for that bug.
We have a design of two 6509 running in a VSS with dual supervisor each having fthree 10/100/1000mb etherner modules. We have diagnosed a wierd problem that none of the switchports in module 1 and 2 on either switches are having layer2/layer 3 connectivity.
Tried everything from changing the cables to changing the end device but no luck with it.
Module results show pass and no errors in the logging.
I am trying to find the serial number on the CLI that matches the serial number sticker on the back of a WS-C2948G-GE-TX switch that runs CatOS. I am running code cat4000-k9.8-3-2-GLX.bin. I have 4 different switches and all the stickers have a serial that starts with JPE.. and both "show version" and "show sprom 1" and "show sprom 2" gives me a completely different serial number that starts wtih JAE... All of these serial numbers I get from the CLI match with each other. The command "show sprom chassis" says "Feature not supported."
Is it possible to find the serial number that matches the sticker from the CLI on a 2948G? Why does Cisco make this so confusing?
I have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View RelatedFacing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedI currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
How to identify the OID to show the “total MAC Addresses In Use” on a 6509, This is the value we can see from a show mac-address counters, and I want our Solarwinds system to poll for it.
View 1 Replies View RelatedRecently, I have increase to 4G memory ram to the router 3945 but when I show version, it does not state there are 4G in there but still showing the old mem ram size. Why is that so ?
View 3 Replies View RelatedThis is the second one of the new ASA 55.5X series appliances where I have seen this issue:When I SHOW VERSION, I can see the serial number displayed. However, this does not match the serial number from the sticker affixed to the outside of the chassis.This makes it confusing on opening TAC cases and for updating licenses.
View 8 Replies View RelatedI just need to upgrade existing FWSM of 6509.FWSM Firewall Version 2.3(1)is it possible to upgrade to the version of 4.X .If not to which version is safe?And also I need to steps of doing FWSM upgrade.
View 1 Replies View Relatedi've got a Cisco 877 router connected to an ADSL link. i'm using the show dsl interface atm just to have a look on its performance. i've tried to search on Cisco website on how to interpret the output but a blog gave me more info [URL]. My question now is, what readings do i consider? is it on the left (ATU-R) or on the right (ATU-C)?
877ROUTER#sh dsl int atm0 ATU-R (DS) ATU-C (US)Modem Status: Showtime (DMTDSL_SHOWTIME)DSL Mode: ITU G.992.1 (G.DMT)ITU STD NUM: 0x01 0x01Vendor ID: 'ALCB' 'ALCB'Vendor Specific: 0x0000 0x0000Vendor Country: 0x00 0x0FCapacity Used: 31% 85%Noise Margin: 34.0 dB 10.0 dBOutput Power: 16.0 dBm 12.0 dBmAttenuation: 10.0 dB 6.0 dBDefect Status: None None Last Fail Code: NoneSelftest Result: 0x00Subfunction: 0x15Interrupts: 1453 (2
[code]....
I have encounterd a broplem on my Cisco 805 model.
When i use the command "show ip interface brief" the status shows "up" but the protocol is "down" on my serial interface.
The link between my to sites is down after this happend.
I did a sh inv on my newly built 2x Cat 3750X + Cat 3750-24FS stack running 12.2(58)SE2). It only showed 3 of the 4 Cat 3750X PSUs - Sw1 PSU 0, Sw2 PSU 0 and Sw2 PSU 1.
Switch#sh invNAME: "1", DESCR: "WS-C3750X-24"PID: WS-C3750X-24T-S , VID: V02 , SN: FDO*******D
NAME: "Switch 1 - Power Supply 0", DESCR: "FRU Power Supply"PID: C3KX-PWR-350WAC , VID: V01D , SN: DTN1533L00N
NAME: "2", DESCR: "WS-C3750X-24"PID: WS-C3750X-24T-S , VID: V02 , SN: FDO*******6
NAME: "Switch 2 - Power Supply 0", DESCR: "FRU Power Supply"PID: C3KX-PWR-350WAC , VID: V01D , SN: DTN1533L08M(code)
I am using Cisco 2911 & IOS version is 15.1. My problem is that after some days (e.g. 15-20 days), the routing table suddenly stops updating & then I have to enter the default route again to make it up. I am using Track 1 to track default route here. After primary link goes down, the Track is also going down but after coming the primary link up, the track is not coming up. So, I have to add the default route again to make it up.
View 2 Replies View Relatedwe've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?
View 3 Replies View RelatedFor an assignment in a class I am taking I created a simple network using GNS3 and set up static routing. Everything works fine, I can ping all of the hosts. One of the questions I am supposed to fill out is what happens when I use the "show ip route" and "show ip protocols" commands. When I use "show ip route" I get what seems to be the correct output. However when I use the "show ip protocols" command nothing happens. No output, no error, no nothing. It just goes right back to the prompt. This happens exactly the same on both routers in my network. incase it matters the router is c3640.
PS. would the output be non-existent because I have not set up any ip protocols. In a similar assignment I set up rip and when I used "show ip protocols" i did get what appeared to be the correct output. However I didn't write it down and when I put in the command again about an hour later after I took a break I also did not get an output until I re-entered the rip related commands.
I'm troubleshooting a 3750 switch stack problem where computers are showing input and CRC errors. I'd like to be able to execute a "show interface" command that will show me only the line showing the switch port and the line showing the input errors, but so far I can't figure out a way of combining those two parameters.
If I do "show interface | include Ethernet[0-9]�" I get all the lines showing the port numbers:
GigabitEthernet1/0/1 is up, line protocol is up (connected)
GigabitEthernet1/0/2 is up, line protocol is up (connected)
GigabitEthernet1/0/3 is up, line protocol is up (connected)
[Code].....
I'm trying to examine the ARP table on specific phy ports on a SG300 switch. The Cisco CLI guide shows this syntax:
show arp [ip-address ip-address] [mac-address mac-address] [interface-id]
Using the CLI and the "?" key to get assistance, I'm not successful:
switch3#show arp
configuration Display ARP related configuration
ip-address Filter ARP show by IP
mac-address Filter ARP show by MAC
[Code]...
I don't have http server enabled, I prefer SSH and CLI to do my work.
The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-
Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)
I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports
Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each
and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.
although cisco sw advisor said that the best IOS for my hardware 6509 Sup720 IOS: (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF16 suits the WiSM; And I tested it already with WiSM version 5.0 but when I've upgraded the WiSM to version 6.0 the service interface from the switch side says:
B5_Noc2_CS1(config)#int gig 4/9
% This interface cannot be modified
as the customer refuse to upgrade the switch IOS & He wants to use the latest ED WiSM sw 6.0;
If client gateway = 192.168.64.9 then next-hop = 192.168.64.8 else use default-route 0.0.0.0
I know it's possible to do a route-map match ip-address ACL list. But is it possible to match on gateway?
Some info about hardware and config:
6509-E in VSS (IOS 12.2(17r)SX5) withVS-S720-10G supervisor.
All routes are static, IP for 192.168.64.9 is on SVI vlan.
I have two ISPs. Each is on it's own subnet connected to the 6509 MSFC/Switch. FW1 is on 100.1.100.0/30 and FW2 is on 200.1.200.0/30 subnet. My goal is route all traffice going to the Internet from subnet 10.133.3.0/24 to FW1 and all other subnets across the organization to FW2. I am not sure if I need to use ACL / Static route combo, or just a static routes or ACLS?
View 5 Replies View RelatedWe have a Catalyst 6509 switch, and we hope to use policy based routing to redirect http traffic to my proxy server, where I can find the configuration example?
View 11 Replies View RelatedI would like to ask you if it's possibile to block routing between some Vlan for just once of them.
Maybe I can explain better:
I've got a Cisco 6509 with 4 configured vlan interfaces
Int Vlan 10 10.10.1.0/24
Int Vlan 20 10.10.2.0/24
Int Vlan 30 10.10.3.0/24
Int Vlan 40 10.10.4.0/24
Vlan "10" is the phone voip Vlan and it must not talk with the others Vlan. The others Vlan can comunicate normally except with Vlan "10".
Pratically Vlan "10" needs to be isolated from the others.
This equirement comes becouse Vlan 10 is wireless and has the WEP key encryption (very weak protocol). Some Phone couldn't support the WPA2 key and I need to avoid an unauthorized external client, cracking the WEP key and connecting to this WiFi, could have free access to the others Vlan.
I have a problem on my catalyst 6509 on which I would like to do the following things :
I have some Vlans in which multicast is enabled.
In tose Vlan theres is a router which is default router for equipements.
I had enabled multicast routing because some Vlan needs to exchange multicast informations, but I wolud like to make difference between Multicast traffic. For example I have 5 vlans:
Vlan 1 and 2 need to exchange Multicast informations but the don't need multicast information from Vlan 3 and 4
Vlan 3 and 5 need to exchange Multicast informations but the don't need multicast information from Vlan 1 and 2
Vlan 5 is independant Vlan but doesn't need to have multicast information from all others vlan.
Last problem, equipement on differents vlan can use the same Mulkticast group address. In this case, Multicast routing is not working between Vlan 1 to Vlan 2 and Vlan 3 to Vlan 4.
I need to setup my 6509 with PBR going to two different Firewalls. The 6509 has vlans and multiple serial interfaces. What/where do I install the policy-maps? I want to direct one of the vlans to one firewall and the other vlans and wan subnets to the other firewall.
View 26 Replies View Relatedhow can I show the DHCP-range of a router if I don't have privilege level? (not in enable-mode),I can do a "show ip dhcp pool" - this will show me the range which is configured with the network-command.But there are also some dhcp-exclude-addresses which I can't see.... (I did a test on a router with full privilege-access)I need this because I have a router with limited access from our provider.
View 0 Replies View RelatedI am working with 3750 switch.I console the switch and turn it on and it doesn’t show text in hyper terminal with any BAUD (I tried all the speeds). The hyper terminal works with other switches so the problem is not with the hyper terminal.when I tried to break the password it stuck after I was writing "flash_init" and when I entered or typed text it show only garbage characters. I tried to break the password with all the speeds and it shows garbage output. I tried to turn on the switch and hold control + break and it showed the text only with the speed 115200, but after I left holding and tried to type it showed only garbage again. Also I tried to copy text from the notepad to the hyper terminal.
View 6 Replies View Relatedis there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
View 5 Replies View RelatedI'm dealing with a 4506 switch that whn I try to apply "sh auth sess int xx" I get "Invalid Input Detected" ... Is there any way that I can get the authenticated session over a port even if I can't apply "sh auth sess int"?
View 1 Replies View Related