I just need to upgrade existing FWSM of 6509.FWSM Firewall Version 2.3(1)is it possible to upgrade to the version of 4.X .If not to which version is safe?And also I need to steps of doing FWSM upgrade.
View 1 Repliesprovide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM
View 10 Replies View Relatedi am using Cisco ASA 5510 with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3
View 6 Replies View Relatedwhat the upgrade path is for 5505 ASA . I have one which is version 7.2 and need to upgrade it to 8.4(5). I have read that it needs to upgraded btwn major release versions.Not sure if I need to upgrade from 7.2 - 8.0 , then form 8.0 - 8.2, then from 8.2 - 8.3 and finally 8.3 to 8.4 or can I just upgrade from 7.2 - 8.2 and then from 8.2 - 8.4 .Also what is the minimum memory requirements for vers 8.4 .my ASA running on vers 7.2 currently has 256Mb Memory and I will be upgrading this to 512MB before I do the upgrade the image above?
View 4 Replies View RelatedI'm getting an error message on my 506E that is saying not enough flash space to install the new version 8 software. I did a clear flashfs command and then tried again but get the same error. Do the PIX 506E can be upgraded from version 6 to version 8? I am trying to install pix804-28.bin.
View 3 Replies View RelatedI am looking to upgrade a 5510 that is currently on code version 8.0(4) to code version 9.1. I know I will have to upgrade to 1gb ram, but can i just upgrade straight to version 9.1 or do I need to follow an upgrade path? This is a standalone device so I am planning on downtime.
View 8 Replies View RelatedI have a ASA5550, with a IOS version 8.2(5).
I would like to upgarde to the latest version, and I believe it is 9.1.1.
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Is there a way I can check the version of each device on two Cisco 6509 if they are Virtually connected (VSS)? When I enter the command show version, it only shows one result, unlike show module, you have an option to choose which switch by entering 1 or 2.
View 3 Replies View Relatedalthough cisco sw advisor said that the best IOS for my hardware 6509 Sup720 IOS: (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF16 suits the WiSM; And I tested it already with WiSM version 5.0 but when I've upgraded the WiSM to version 6.0 the service interface from the switch side says:
B5_Noc2_CS1(config)#int gig 4/9
% This interface cannot be modified
as the customer refuse to upgrade the switch IOS & He wants to use the latest ED WiSM sw 6.0;
I have a C2950 Switch & I am trying to upgrade the IOS version of it so that I can proceed with learning about SSH. My current version of 12.1 does not have Enhanced Imaging. I am so new to Cisco, that I have spent hours trying to find the correct page, or link, or anything that can enable me to upgrade to a later version.
View 6 Replies View RelatedI have installed ACS Windows 2003 R2 Services Pack 2.
I am upgrading of version 4.1.1.23 to version 4.2.1.15. Recommended by Cisco.
Before of update everthing works fine.
After of upgrade, this does not authenticate user, sends the next message "External user not found", "Authentication session invalidated" and "internal error".
The mapping is ready. annex image.
I want to upgrade my Cisco ACS Engine appliance 1120 from software version 3.3 to the latest version (5.x). How do I go about this?
View 2 Replies View RelatedI have succeeded in turning the AP from autonomous into LWAPP mode with the Ugrade tool. The AP has been loaded with c1130-rcvk9w8-tar.124-10b.jda due to the upgrade tool version 3.4,After reboot, the AP appears on the vwlc (YES!) however as you can see in APvwlc.jpg the AP now have version 3.0.51.0.I need the AP to be loaded with version 7.3.101.0 with FlexConnect mode.
View 24 Replies View RelatedI have 4 switches of 3750. I need toupgrade all the switches, but I can't to disconnect the stack cable.How I can to upgrade the version without to disconnect the stack cable?
View 2 Replies View RelatedWe have five cisco WLC 5508 and one WCS .The WLC is running on 7.0.116.0 version at present but we want to upgrade it to 7.4.100.0 but on cisco site at download location , the below thing is mentioned...
WLC Version 7.4.100.0 will need Prime Infrastructure Version 1.3 to be managed, Version 1.3 is not yet available to download at this point of time
Access Point Model----Cisco 3501i Series
So i want to know, can i upgrade it to this version when we are having the WCS in our network ?
I would like to upgrade our three WLC 4402 controllers from version 7.0.116.0 to 7.0.235.3. I have downloaded the two files (AIR-WLC4400-K9-7-0-235-3-ER.aes and AIR-WLC4400-K9-7-0-235-3.aes). Which one should I upgrade/install first?
View 4 Replies View RelatedWe are trying to test ios upgrade for Cisco 6509 switch with issu (in service software upgrade). We were able to upgrade the ios but there is one issue in issue 6509's supviseengine720 gigabit port lost the connection during the upgrade process.
View 1 Replies View RelatedI currently have this in our Sup720:
boot system flash bootflash:s72033-jk9o3sv-mz.122-17a.SX3.bin
boot bootldr sup-bootflash:s72033-psv-mz.122-17a.SX1.bin
I downloaded s72033-mp001-pz.122-33.SXH5
I read the documentation on Upgrading Software Images on Catalyst 6000/6500 Series SwitchesURL
I was wondering do I copy the s72033-mp001-pz.122-33.SXH5 to the sup-bootflash and bootflash? In the example it also uses disk0: but I get a <No device available>. Also keep in mind we're upgrading the application and maintanence partitions also. So this is a big upgrade and I've never done this before.
I guess the 2 things I want to know is:
1) Can I copy the s72033-mp001-pz.122-33.SXH5 to both the sup-bootflash and the bootflash? Can I run it just copying it to the sup-bootflash?
2) It was my understanding that I only needed one image file for the upgrade but the documentation says I need
"a. the main software image
b. the bootloader image"
Do I need another file? I'm a little confused. I did notice the files had different names and sizes and so do the ones on my current Sup 720.
And we are doing this tomorrow and I just happened to be reviewing the documentation one more time and somehow missed this.
Have a new 6509-E router with 2 sup2T blades. However it came with IPbase and we need to put Ipservices on it. I have copied ipservices IOS to bootdisk and slavebootdisk.
However I cannot get get to the boot command to point to bootdisk. It only allows me to point to flash:
)#boot system flash ?
WORD System image filename
<cr>
Yet I don't seem to have an option to copy this new IOS to flash. How do I get to copy it to flash:
Here is the original show boot command:
sh boot
BOOT variable = bootflash:s2t54-ipbasek9_npe-mz.SPA.150-1.SY1.bin,1;
CONFIG_FILE variable =
[Code].....
I want to upgrade a 5508 WLC from version 6.0.196.0 to the most recent 7.4or 7.3 is it ok to skip so many versions, will this cause an issue?
View 9 Replies View RelatedI just bought RV042G with serial number NKS16120688 to replace old RV042 which is cannot upgrade to new version firmware(from above V.4).After I connect to my TOT isp modem to new rv042g, the router distributes ip (DHCP), get dns from isp normally but it cannot connect the internet at all.It seems this new firmware is not compatible with tot isp in Thailand while old rv042 with old firmware can run smoothly.I have to try many things such as change wan port, change modem and also buy another new RV016, but results still the same.
View 1 Replies View Relatedhow can i upgrade to Mini IOS Version 7.3.1.73 on the AIR-CAP 3502I. we some that have Mini IOS Version 7.3.1.73 and some that have Mini IOS Version 7.0.112.74. want them all the same.
View 1 Replies View RelatedWe just purchased the following items:
(1) R-PI-1.1-500-K9
(2) PRIME-NCS-APL-K9
I want to know how I can upgrade to the latest version of Cisco Prime Infrastructure.
I have this 4900M running version 12.2(54)SG1. I the log I get this 3 lines:
May 8 08:32:15: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 429 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
May 8 08:32:24: %C4K_L3HWFORWARDING-4-FLTCAMPARITYERROR: (Suppressed 866 times)FL Tcam Perr with no FwdEntry Hw index: 3144 Hw entry: Sw entry:
May 8 08:32:45: %C4K_SWITCHINGENGINEMAN-4-TCAMINTERRUPT: (Suppressed 432 times)flCam0 aPErr interrupt. errAddr: 0xC48 dPErr: 1 mPErr: 0 valid: 1
They seems to be coming on regular basis, repeating every minute. I've tried Google and the most relevant info I can find is this {URL}. But it says "Upgrade software to IOS version 12.2(52)SG or later OR 12.2(50)SG4 or later. ". I'm already running 12.2(54), so why does this 3 line repeatedly show up in the log every minute.
I need to upgrade IOS on my 6509 MSFC2. Below is the software version I have on the Sup2 and msfc2. The reason I need to upgrade the msfc2 IOS is that I need to implement ip sla/object tracking and it is not supported by the current version of IOS on msfc2. How do I select the new IOS that I should upgrade the msfc2, in order to achieve object tracking...I see a long list of IOS in the software download section of 6509 msfc2, but not sure which one to choose..
WS-X6K-SUP2-2GE: Sw : 8.6(4)
WS-F6K-MSFC2: Sw : 12.1(19)E1
Tonight we were performing an IOS upgrade on our 6509 VSS to 122-33.SXI6. Both 6509's have dual Supervisor cards installed. Initially we had problems with switch 2 slot 5 supervisor returning to rommon however switch 2 slot 6 supervisor loaded correctly. After manually setting the boot var in rommon, switch 2 slot 5 supervisor reloaded correctly.
After all supervisor's were online we noticed when looking at " show switch virtual redundancy" that sw 1 & 2 slot 6 supervisors were running the correct IOS version but sw 1 & 2 slot 5 were running different IOS versions, however when looking at the show version we are running on the upgraded IOS??? See output below...
Why the active supervisor has loaded the incorrect IOS the VSS is running on the upgraded IOS? I have verified the IOS was copied correctly to each supervisor bootdisk, I see no issues.
My Switch Id = 1 Peer Switch Id = 2 Last switchover reason = none Configured Redundancy Mode = sso Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :----------------------------------------------- Current Software state = ACTIVE Uptime in current state = 3 hours, 38 minutes Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)Technical Support:
[code].....
Will I be OK doing a eFSU Upgrade from s72033-ipservicesk9_wan-mz.122-33.SXI2a to s72033-ipservicesk9_wan-mz.122-33.SXJ1?
I only have a single supervisor in each chassis.
Should I be ok with just following the eFSU upgrade instructions in the below?
[URL]
We have Cisco 4402 Wireless Lan Controller with Software Version 3.2.171.6 and we want to upgrade it to latest version.
What is the latest version to upgrade the WLC?
Also since WLC is running on very lower version is it possible to upgrade to the latest version directly or we have to move it step by step to upgrade this to latest version?
How do I upgrade the boot rom version on the 7200 router? I am running IOS Version 12.4(22)T and when I plug in the serial ds3 card in my router it keeps rebooting with a watch dog error ( see below). Also, what version should I upgrade to?
Router#sh verCisco IOS Software, 7200 Software (C7200-SPSERVICESK9-M), Version 12.4(22)T, RELEASE SOFTWARE (fc1)Technical Support: [URL] Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Fri 10-Oct-08 10:10 by prod_rel_team
ROM: System Bootstrap, Version 12.2(4r)B, RELEASE SOFTWARE (fc1)BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(13)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
Router uptime is 0 minutesSystem returned to ROM by power-onSystem image file is "sup-slot0:/c7200-spservicesk9-mz.124-22.T.bin"
[code]....
I am going to upgrade a number of catalyst 2960s-switcher to the latest IOS- version. The best solution for me would be if all the switches could be reloaded at the same time to shorten the maintenance-windows. So my question is: If I run the upgrade (archive down load -sw) before the maintenance-windows WITHOUT the reload-option, will then the switches continue to run without interruptions with the current IOS- version and config until I run reload manually?
View 3 Replies View RelatedI would upgrade the firmware before deciding to replace router with a new one. I noticed there have been several updates to the firmware since I originally installed the router with the current available firmware version of 1.35NA.
View 12 Replies View Related