Cisco Routers :: RV042G Cannot Upgrade To New Version Firmware

Oct 28, 2012

I just bought RV042G with serial number NKS16120688 to replace old RV042 which is cannot upgrade to new version  firmware(from above V.4).After I connect to my TOT isp modem to new rv042g, the router distributes ip (DHCP), get dns from isp normally  but it cannot connect the internet at all.It seems this new firmware is not compatible with tot isp in Thailand while old rv042 with old firmware can run smoothly.I have to try many things such as change wan port, change modem and also buy another new RV016, but results still the same.

View 1 Replies


ADVERTISEMENT

Cisco Routers :: Upgrade From RV042 To RV042G

Mar 5, 2013

I'm about to upgrading our RV042 to RV042G since everything in the Network ist ready for Gigabit except the RV042
 
I think it's important to mention that another RV042, which is at a 2nd location, will remain for the VPN connection between the two locations. (Older Hardware are used at the 2nd location).
 
My Question is, are there any known issues, which should be cleared before changing the router.
 
Mainly issues with configuration migration and compatibility between RV042 and RV042G VPN connections.

View 3 Replies View Related

D-Link DIR-655 :: Current Version 1.35NA - Upgrade Firmware?

Jul 17, 2011

I would upgrade the firmware before deciding to replace router with a new one. I noticed there have been several updates to the firmware since I originally installed the router with the current available firmware version of 1.35NA.

View 12 Replies View Related

Linksys Cable / DSL :: WAG120N Upgrade Firmware Version (1.0.0.16)?

Jun 11, 2012

I made the change WAG120G (GREAT) for WAG120N (**bleep**) and I confess that I was somewhat disappointed, the quality of the company fell dramatically. Unlike its predecessor this modem / router is bad in many ways and first of them is support for Macintosh products, the connection drops constantly and have to get on and off the wifi to work. The modem restarts and constantly drops the connection status and its predecessor NEVER did that. iPad, iPhone and Macbook can not even keep me surfing for more than one hour, the connection just stops working. Even the cable connection, my Xbox sometimes worth it to maintain a stable connection in Live. The modem has been updated with the latest firmware version (1.0.0.16). Another thing I noticed is that the modem takes A LOT to connect with the operator. It's bad, it's expensive and does not work! I

View 9 Replies View Related

Linksys Wireless Router :: E1200 Will Support The Upgrade Version 2 Firmware

Jan 15, 2013

I have a Cisco E1200 router that is currently running firmware version 1.0.03 build4 Mar 1, 2012. Can I upgrade to the latest version 2 firmware ? How do I know if my router hardware will support it ? 

View 4 Replies View Related

Cisco Routers :: Replace RV082 Firmware Version 2.0.0.19 With New 4.0.2.08

Sep 13, 2011

I have an old RV082 with firmware version 2.0.0.19. I want to replace it with a new RV082 firmware version 4.0.2.08.I exported the fv2 config but can't restore it on the fv4. I get "invalid file type" error. The fv4 box is looking for a .config file and the fv2 box saves as a .exp file.

View 4 Replies View Related

Belkin Routers :: F9J1106 What Is Latest Firmware Version

Jan 31, 2013

Just purchased a Belkin AC1200 Router Modem and unable to locate the model number what is the current firmware version It is the UK model and I guess it must be very new?

View 4 Replies View Related

Belkin Routers :: Version 1 Firmware For F5D9230-4 Wireless G Plus Mimo?

Mar 17, 2013

Where do I find the firmware upgrade for version one (1) of my F5D9230-4 Wireless G Plus Mimo router?

Only versions two (2) through five (5) are listed on the F5D9230-4 firmware page: [URL]

View 6 Replies View Related

Belkin Routers :: Recent Version Firmware Update For F5D7234-4v1

Jun 10, 2013

MY belkin router model no :F5D7234-4v1, recognizes only my laptop and my other devices such as mobile and tab are getting the signal and w-fi gets connected but the internet is not working. when contacted service provider he asked to upgrade the firmware. Is there any recent version firmware upgrade of the model. current version is F5D7234-4_UK_1.00.01.

View 1 Replies View Related

Belkin Routers :: F5D7234-4v2 - Recent Version Firmware Update?

Jun 9, 2013

what is the recent version Firmware update for Belking router model number : F5D7234-4v2

View 1 Replies View Related

Belkin Routers :: F5d8235-4 Downloaded Correct Version For Firmware Update

Feb 23, 2013

When i try to update the firmware it tells me the it is an incompatible update.ive followed all the instructions.my model number is f5d8235-4 v2.i have downloaded the correct version for the firmware update (2).

View 5 Replies View Related

Belkin Routers :: How To Update Firmware On N Wireless Router With Version 2000

Feb 2, 2013

How do I update the firmware on my N wireless router with version 2000? It says there is an update, but I can't update it with the one firmware update that's available for download.

View 4 Replies View Related

Cisco Routers :: RVS4000 Firmware Upgrade To Ver 2.0.3.2?

Dec 27, 2012

I have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file.  I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error' 

View 2 Replies View Related

Cisco Routers :: Wrvs4400n Firmware Upgrade With VPN

May 12, 2013

I have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
 
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?

View 3 Replies View Related

Cisco Routers :: RV016 V1 Firmware V 1.3.2 Upgrade To V2.0.0?

Jan 10, 2013

I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1

View 5 Replies View Related

Cisco Routers :: RVS4000 - Upgrade From 2.0.0.2 To 2.0.2.7 Firmware

Jul 21, 2012

I've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
 
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
 
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
 
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?

View 1 Replies View Related

Cisco Routers :: SRP527W - Firmware Upgrade

Feb 14, 2011

I've been having the lockup issue with the SRP527W (in fact this has been an extremely embarrassing situation after spending 4 x what I could have on a Net gear type unit, to do the same task).  I've not yet managed to get hold of the new firmware (MR3) as I've not received the email with a link. 
 
On another note, I'm not sure if this has been covered in other posts, but, when my unit stops working (Wireless still alive, no internet) - the CPU hits and stays at 100% and only a reboot fixes it.

View 5 Replies View Related

Cisco Routers :: Firmware Upgrade Utility For Rvs4000v2

Apr 6, 2013

I use cisco rvs4000v2. I had to restore the factory settings, and I use Cisco RVS4000 Firmware Upgrade Utility version 1.3. But I did not know that it is for Cisco RVS4000v1. The utility will install RVS4000 firmware v1.3.0.5. Now I can not restore to factory settings.how do I restore the factory firmware cisco rvs4000v2?

View 1 Replies View Related

Cisco Routers :: RV082 Firmware Upgrade V4.04 Fails

Sep 4, 2011

I have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.

View 1 Replies View Related

Cisco Routers :: RV042 Firmware Upgrade Failure To 4.0.2.08-tm?

Jun 28, 2011

Tried upgrading my firmware to 4.0.2.08-tm and now I cannot log in via the web interface. The router boots and gets out to the internet. It still allows incoming vpn connections. The login screen displays and will display an error message if I use incorrect credentials, but if I log in properly and am directed to the routers web config homepage at "192.168.1.1/default.htm", I get a 404 error message. Telnet does not work either (not sure if it's on, never used it before) 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.As if the web pages after the login screen got removed or corrupted after the update.
 
SN is NKS10403247
 
I realize there is a newer version. Attempted the upgrade incrementally since I could not find documentation specifiying if that was required or not.

View 5 Replies View Related

Cisco Routers :: Unable To Upgrade Firmware On RVS4000?

Jan 19, 2012

Currently on V1.3.0.5. Looking to upgrade to latest version, however the upgrade firmware page is greyed out. Same under Firefox 9 or IE 8. I have already rebooted router, with no change in behavior.

View 2 Replies View Related

Cisco Routers :: RV082 Firmware Upgrade Breaks WAN

Dec 1, 2009

I have upgrade the firmware on several RV082 (and RV042) model routers, and all of them have had subsequent WAN connectivity loss. The WAN works for a while, then stops working until the router is restarted, then fails shortly thereafter. I would assume it was some configuration corruption on incompatibility with the upgrade, but the symptom has been universal. EVERY 2.x upgrade I've made to a RV082 or RV042 router has exhibited this symptom. Reverting to the 1.3.98-tm firmware fixes the issue.

View 14 Replies View Related

Cisco Routers :: RV082 Firmware Upgrade Error?

Jul 6, 2012

 This morning i upgraded a remote RV082 to 4.2.0.1 from 4.0.4.1.  Numbers could be off slightly since i'm going from memory.   I never got the normal acknowledgement the transfer was complete but after an ample amount of time closed the tunnel from my end, re- established my vpn but when i went to log in i received: RV082 firmware upgrade error? The requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist./quotei googled it and found similar occurrences with earlier upgrades.  I'm assuming it didn't reboot itself upon completion of the xfer, at least i'm hoping a cold reboot will correct this but as i'm remote and this install doesn't have an ethernet power controller i'm stuck until monday. Should i bring a spare RV082 just in case.

View 3 Replies View Related

Cisco Routers :: RV042 V3 Hardware After Upgrade From 4.1 To 4.2 Firmware

Feb 5, 2013

I have a problem with a brand new RV042 v3 hardware,I upgraded the firmware from 4.1 to 4.2 and now can not see the web interface in firefox, the login appears and the left menu appears, but at the right nothing is shown
 
I tried doing the firmware rescue util but the same problem happens.if this a know issue? Should I RMA it?

View 2 Replies View Related

Cisco Routers :: Unable To Upgrade Firmware On SRP546W?

Nov 6, 2011

I am unable to upgrade the firmware on the SRP546W
 
The admin guide states goto Administration > Firmware Upgrade > Choose File > Browse > Click Upgrade
 
There is no such item to select in the Administration section All I have in the administration section is
 
Remote Management
Time Setup
User
 
Also was wondering if it is possible to change the Annex B version I have to Annex A if I bring it back to England?

View 3 Replies View Related

Belkin Routers :: F5D9231-4v1 Will Not Upgrade Firmware?

Mar 25, 2013

I am trying to update my firmware from v1 to v2 on my F5D9231-4 Router, after downloading from the support page and trying to install it I get the following error "Upgrade file is not the correct type or version for this device. Upgrade failed. Please obtain the correct file and try again" I double checked the model numbers.

View 2 Replies View Related

Belkin Routers :: F5D8233 4N Need To Upgrade The Firmware

Dec 30, 2012

F5D8233-4 N Wireless Router - Firmware Update,l I am trying to upgrade the firmware of this router which currently it's 3.01.29 to the latest one which is 4.00.04 but every time I try to manually install it, it comes back with an error message saying it's not the tight update but it is.

View 1 Replies View Related

Cisco Firewall :: Software Upgrade For ASA 5520 Version 7.0(1) To Version 8.4?

Apr 3, 2012

provide me with the important links which can show me how to do the software upgrade for my ASA 5520 ver 7.0(1) to ver 8.4 ? as well as the ASDM

View 10 Replies View Related

Cisco Routers :: Slow Internet After RV042 Firmware Upgrade?

Jan 31, 2012

After upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites.  In some instances, when the page does load, it lacks many graphics.  Frequently, I also receive a "server not found"error.  In all cases, reloading the page (once it has loaded) results in a complete page display.  This is occuring on two MacBook Pros and also on an iPad.  The router is a version 1, so no further upgrades are available.  I contacted support, but since it is out of warranty, they are unwilling to assist.  Prior to the upgrade, everything worked fine, as it has for 5 years.

View 1 Replies View Related

Cisco Routers :: Router RV042 Upgrade To Older Firmware

Dec 13, 2012

We have a CISCO RV042.  We are about to begin a VIOP service with Vocalocity who state:
 
The RV042 is a wired router that requires no configuration adjustments for the firmware versions we tested. Version 1 and 2 are compatible. Version 3 is NOT. Firmware Reviewed: 1.3.12.6 | 1.3.12.19
 
Our router's firmware is :    1.3.8.2 (Feb 12 2007 10:43:08)
 
Can we upgrade to 1.3.12.6 or 1.3.12.19?  What is meant by Version 1, 2 and 3?

View 3 Replies View Related

Cisco Firewall :: How To Upgrade ASA 5510 Version 8.0(4) To Version 8.3

May 10, 2011

i am using Cisco ASA 5510  with ASA Version 8.0(4) and memory 256MB. me to Upgrade it to 8.3

View 6 Replies View Related

Cisco Routers :: RV016 Shows A Browser With No Connectivity When Try To Upgrade Firmware

Jan 31, 2012

I've downloaded the file "RV0XX-v4.1.0.02-tm.bin" from Cisco's web site. The current firmware in the RV016 router is V3. I log into the router with IE9 (or even firefox), navigate to the system management section, upgrade firmware tab. Browse to the file above and click the button to upgrade. Nothing happens for a few seconds, then the browser displays cant load this page. (Same results if I use the file "RV0XX-v4.1.1.01-sp.bin" as well.)

View 1 Replies View Related

Cisco Routers :: RV220W - Upgrade To 1.0.4.17 Failed Due To Invalid / Corrupted Firmware

Mar 10, 2013

I have a RV220W running 1.0.1.0. When trying to upgrade to 1.0.4.17 I receive an error: "Upgrade failed due to invalid/corrupted firmware".
 
I found this article: [URL]
 
I assume I have to do a factory reset then an upgrade in order to upgrade properly.
 
If I do a backup running 1.0.1.0, then upgrade to 1.0.4.17, then do a restore, would that put me back to 1.0.1.0?  I'm trying to avoid configuring the router manually all over again. 

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved