I use cisco rvs4000v2. I had to restore the factory settings, and I use Cisco RVS4000 Firmware Upgrade Utility version 1.3. But I did not know that it is for Cisco RVS4000v1. The utility will install RVS4000 firmware v1.3.0.5. Now I can not restore to factory settings.how do I restore the factory firmware cisco rvs4000v2?
View 1 RepliesI have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1
View 5 Replies View RelatedI've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?
I've been having the lockup issue with the SRP527W (in fact this has been an extremely embarrassing situation after spending 4 x what I could have on a Net gear type unit, to do the same task). I've not yet managed to get hold of the new firmware (MR3) as I've not received the email with a link.
On another note, I'm not sure if this has been covered in other posts, but, when my unit stops working (Wireless still alive, no internet) - the CPU hits and stays at 100% and only a reboot fixes it.
I just bought RV042G with serial number NKS16120688 to replace old RV042 which is cannot upgrade to new version firmware(from above V.4).After I connect to my TOT isp modem to new rv042g, the router distributes ip (DHCP), get dns from isp normally but it cannot connect the internet at all.It seems this new firmware is not compatible with tot isp in Thailand while old rv042 with old firmware can run smoothly.I have to try many things such as change wan port, change modem and also buy another new RV016, but results still the same.
View 1 Replies View RelatedI have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies View RelatedTried upgrading my firmware to 4.0.2.08-tm and now I cannot log in via the web interface. The router boots and gets out to the internet. It still allows incoming vpn connections. The login screen displays and will display an error message if I use incorrect credentials, but if I log in properly and am directed to the routers web config homepage at "192.168.1.1/default.htm", I get a 404 error message. Telnet does not work either (not sure if it's on, never used it before) 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.As if the web pages after the login screen got removed or corrupted after the update.
SN is NKS10403247
I realize there is a newer version. Attempted the upgrade incrementally since I could not find documentation specifiying if that was required or not.
Currently on V1.3.0.5. Looking to upgrade to latest version, however the upgrade firmware page is greyed out. Same under Firefox 9 or IE 8. I have already rebooted router, with no change in behavior.
View 2 Replies View RelatedI have upgrade the firmware on several RV082 (and RV042) model routers, and all of them have had subsequent WAN connectivity loss. The WAN works for a while, then stops working until the router is restarted, then fails shortly thereafter. I would assume it was some configuration corruption on incompatibility with the upgrade, but the symptom has been universal. EVERY 2.x upgrade I've made to a RV082 or RV042 router has exhibited this symptom. Reverting to the 1.3.98-tm firmware fixes the issue.
View 14 Replies View RelatedThis morning i upgraded a remote RV082 to 4.2.0.1 from 4.0.4.1. Numbers could be off slightly since i'm going from memory. I never got the normal acknowledgement the transfer was complete but after an ample amount of time closed the tunnel from my end, re- established my vpn but when i went to log in i received: RV082 firmware upgrade error? The requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist./quotei googled it and found similar occurrences with earlier upgrades. I'm assuming it didn't reboot itself upon completion of the xfer, at least i'm hoping a cold reboot will correct this but as i'm remote and this install doesn't have an ethernet power controller i'm stuck until monday. Should i bring a spare RV082 just in case.
View 3 Replies View RelatedI have a problem with a brand new RV042 v3 hardware,I upgraded the firmware from 4.1 to 4.2 and now can not see the web interface in firefox, the login appears and the left menu appears, but at the right nothing is shown
I tried doing the firmware rescue util but the same problem happens.if this a know issue? Should I RMA it?
I am unable to upgrade the firmware on the SRP546W
The admin guide states goto Administration > Firmware Upgrade > Choose File > Browse > Click Upgrade
There is no such item to select in the Administration section All I have in the administration section is
Remote Management
Time Setup
User
Also was wondering if it is possible to change the Annex B version I have to Annex A if I bring it back to England?
I am trying to update my firmware from v1 to v2 on my F5D9231-4 Router, after downloading from the support page and trying to install it I get the following error "Upgrade file is not the correct type or version for this device. Upgrade failed. Please obtain the correct file and try again" I double checked the model numbers.
View 2 Replies View RelatedF5D8233-4 N Wireless Router - Firmware Update,l I am trying to upgrade the firmware of this router which currently it's 3.01.29 to the latest one which is 4.00.04 but every time I try to manually install it, it comes back with an error message saying it's not the tight update but it is.
View 1 Replies View RelatedAfter upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites. In some instances, when the page does load, it lacks many graphics. Frequently, I also receive a "server not found"error. In all cases, reloading the page (once it has loaded) results in a complete page display. This is occuring on two MacBook Pros and also on an iPad. The router is a version 1, so no further upgrades are available. I contacted support, but since it is out of warranty, they are unwilling to assist. Prior to the upgrade, everything worked fine, as it has for 5 years.
View 1 Replies View RelatedWe have a CISCO RV042. We are about to begin a VIOP service with Vocalocity who state:
The RV042 is a wired router that requires no configuration adjustments for the firmware versions we tested. Version 1 and 2 are compatible. Version 3 is NOT. Firmware Reviewed: 1.3.12.6 | 1.3.12.19
Our router's firmware is : 1.3.8.2 (Feb 12 2007 10:43:08)
Can we upgrade to 1.3.12.6 or 1.3.12.19? What is meant by Version 1, 2 and 3?
I've downloaded the file "RV0XX-v4.1.0.02-tm.bin" from Cisco's web site. The current firmware in the RV016 router is V3. I log into the router with IE9 (or even firefox), navigate to the system management section, upgrade firmware tab. Browse to the file above and click the button to upgrade. Nothing happens for a few seconds, then the browser displays cant load this page. (Same results if I use the file "RV0XX-v4.1.1.01-sp.bin" as well.)
View 1 Replies View RelatedI have a RV220W running 1.0.1.0. When trying to upgrade to 1.0.4.17 I receive an error: "Upgrade failed due to invalid/corrupted firmware".
I found this article: [URL]
I assume I have to do a factory reset then an upgrade in order to upgrade properly.
If I do a backup running 1.0.1.0, then upgrade to 1.0.4.17, then do a restore, would that put me back to 1.0.1.0? I'm trying to avoid configuring the router manually all over again.
I attempted a firmware upgrade on my RV042. After an hour, the upgrade was still in progress. I now cannot login into the router using my user name and password (nor the old admin/admin). The router is functioning, but I fear it will eventually fail. How can I recover ability to log in? The Firmward Recovery program doesn't seem to be appropriate for this situation.
View 3 Replies View RelatedI bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
View 2 Replies View Relatedwe have some RV042 Routers with Firmware 1.3.12.x we would like to replace with the new V3 hardware.
We downloaded the migration utility 1.0.2.2, which crashes for at least one device.
The release notes for the utility are for version 1.0.2.8, where some crashes seems to be fixed, but where can we download this actual version?? I can only see the (older) 1.0.2.2..
I tried to use Migration Utility v 1.2.2.0 with configuration file from older unit having VPN tunnels and application is crashing with windows MFC error(on several computers, so it is not related to PC).Migration from V2 to V3 of configuration not having VPN tunnels went ok.
View 4 Replies View RelatedI'm running a new RV042 with the latest firmware (4.1.1.01). I set it up about 2 weeks ago and have been running it without an issue. Today I tried to go in to the web utility to make some changes. I was prompted for the userid/password, which it appeared to accept (if I typed in the wrong ones it rejected it), and then the screen went blank (normally I would get the status screen now.) Instead the screen I get is the light blue of the log-in screen, but there is nothing on it. The router has switched to the page https://192.168.1.1/home.htm I have tried different browsers and accessing it from different computers - the situation is always the same. I have power cycled the router, and there is no change. I suspect the next step is a manual reset to factory defaults - but of course I would rather not (as I didn't save all my settings of course!)
View 2 Replies View RelatedI upgraded my Linksys RV042 firmware to 1.3.12.19-tm and exported the config file, then tried to convert it using RV0xx_Migration_Utility_v1.0.2.2 in order to import it to a new Cisco RV042 (v3). The migration utility returns a config create fail message and fails to convert.
The LOG file ends with:
Get PORT_101 VLAN Group setting fail.
***log end***
how to make this work or how to move config file to v3?
I need to upgrade WCS firmware. Currently i am running with 7.0.172.0 .
View 1 Replies View RelatedRecently I brought SG 300-28.It came loaded with firmware ver 1.0.0.27.Can I upgrade it to ver 1.1.2.0 directly?
View 2 Replies View RelatedI currently have 3 WAP4410n's (actually, they're WAP4410N-E V02s) that have been really unreliable since I got them - so much so that we've had to cron a restart script on another server which is frankly ridiculous - they've always run firmware version 2.0.2.1.
I've tried updating the firmware to new versions in the past with no success - when I do so, it looks like everything's fine, but when I log back in, the fixed IP address information isn't shown, and the wireless is disabled. I can enable it, but I can't select a channel.
At this point, I have to revert back to the old firmware. I've tried restoring to factory setttings before and after the firmware flash, but this hasn't changed anything.
However, recently I was able to flash firmware 2.0.5.3 onto only one of the routers - it worked fine and all information was displayed and wireless enabled correctly. However on the other two, no matter what I try, the firmware won't upgrade succesfully - it looks like everything's fine, but the fixed IP information isn't shown and wireless/channels are disabled.
I have a Dir-655 A3 with the firmware 1.32NA. I cannot get the new firmware 1.35NA to take. The router seems to go through the motions of the upgrade, but at the end, when I log back on, the firmware still says 1.32NA & all custom settings remain.I have upgraded the firmware on this router before and I know that when its upgraded, the router is basically reset to factory settings. All the settings have been backed up and I am attempting this upgrade via a wired connection.
View 2 Replies View RelatedI have a DIR-655 Rev A4.I followed this forum in the past when there were many problems with firmware upgrades beyon 1.21. Because of this I never upgraded and was told to be satisfied that I can still stay with 1.21 as upgrades caused problems for a number of people.Everything still seems fine with 1.21 except the Shareport utility often does not pickup the printer connection upon booting to Windows Vista. I can always work around this by Disable and then Enable. It will then always find the printer. It is a minor annoyance however.Should I still stay with 1.21 or is upgrading to 1.35 NA recommended ? If I upgrade to 1.35 NA is there a downgrade path back to 1.21 if the upgrade does not work well ?
View 12 Replies View RelatedIt baffles me because the admin console doesn't look like it will browse your computer for a firmware update. Rather, it prefers you to specify a tftp or http server. I don't know how I'd set up my computer to be the http or tftp server and it doesn't really go into detail on what configurations or commands that would need to be used. I've used a tftp client in the past to send a firmware to routers and whatnot but not serve one.
View 1 Replies View RelatedWe have 2 ASA 5520s in active/standy. We run IOS 8.2(5)24 and I wondered if I need to upgrade as I see the versions have gone to 8.4 and beyond! We are not getting any issues and I'm aware of the difficult migration from 8.2 to 8.4 etc due to the NAT change.
View 3 Replies View Related