Cisco Routers :: SRP527W - Firmware Upgrade
Feb 14, 2011
I've been having the lockup issue with the SRP527W (in fact this has been an extremely embarrassing situation after spending 4 x what I could have on a Net gear type unit, to do the same task). I've not yet managed to get hold of the new firmware (MR3) as I've not received the email with a link.
On another note, I'm not sure if this has been covered in other posts, but, when my unit stops working (Wireless still alive, no internet) - the CPU hits and stays at 100% and only a reboot fixes it.
View 5 Replies
ADVERTISEMENT
Jan 21, 2013
im guessing there is zero chance of a firmware upgrade for the SRP527W to support more usb devices is there?
View 1 Replies
View Related
Jan 3, 2013
My SRP527W has never had its firmware upgraded since purchase. I had a need to do this recently, but could not find the section under Administration for Firmware upgrade.The only two items under Administration are Time Setup and Switch Setting.I've tried different browsers, to make sure that was not an issue, with no success. Any direct URL to the modem web interface that might allow me to update the firmware. url...Otherwise is there another method using a USB stick or tftp or similar?
View 1 Replies
View Related
Dec 27, 2012
I have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies
View Related
May 12, 2013
I have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
View 3 Replies
View Related
Jan 10, 2013
I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1
View 5 Replies
View Related
Jul 21, 2012
I've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?
View 1 Replies
View Related
Apr 6, 2013
I use cisco rvs4000v2. I had to restore the factory settings, and I use Cisco RVS4000 Firmware Upgrade Utility version 1.3. But I did not know that it is for Cisco RVS4000v1. The utility will install RVS4000 firmware v1.3.0.5. Now I can not restore to factory settings.how do I restore the factory firmware cisco rvs4000v2?
View 1 Replies
View Related
Oct 28, 2012
I just bought RV042G with serial number NKS16120688 to replace old RV042 which is cannot upgrade to new version firmware(from above V.4).After I connect to my TOT isp modem to new rv042g, the router distributes ip (DHCP), get dns from isp normally but it cannot connect the internet at all.It seems this new firmware is not compatible with tot isp in Thailand while old rv042 with old firmware can run smoothly.I have to try many things such as change wan port, change modem and also buy another new RV016, but results still the same.
View 1 Replies
View Related
Sep 4, 2011
I have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies
View Related
Jun 28, 2011
Tried upgrading my firmware to 4.0.2.08-tm and now I cannot log in via the web interface. The router boots and gets out to the internet. It still allows incoming vpn connections. The login screen displays and will display an error message if I use incorrect credentials, but if I log in properly and am directed to the routers web config homepage at "192.168.1.1/default.htm", I get a 404 error message. Telnet does not work either (not sure if it's on, never used it before) 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.As if the web pages after the login screen got removed or corrupted after the update.
SN is NKS10403247
I realize there is a newer version. Attempted the upgrade incrementally since I could not find documentation specifiying if that was required or not.
View 5 Replies
View Related
Jan 19, 2012
Currently on V1.3.0.5. Looking to upgrade to latest version, however the upgrade firmware page is greyed out. Same under Firefox 9 or IE 8. I have already rebooted router, with no change in behavior.
View 2 Replies
View Related
Dec 1, 2009
I have upgrade the firmware on several RV082 (and RV042) model routers, and all of them have had subsequent WAN connectivity loss. The WAN works for a while, then stops working until the router is restarted, then fails shortly thereafter. I would assume it was some configuration corruption on incompatibility with the upgrade, but the symptom has been universal. EVERY 2.x upgrade I've made to a RV082 or RV042 router has exhibited this symptom. Reverting to the 1.3.98-tm firmware fixes the issue.
View 14 Replies
View Related
Jul 6, 2012
This morning i upgraded a remote RV082 to 4.2.0.1 from 4.0.4.1. Numbers could be off slightly since i'm going from memory. I never got the normal acknowledgement the transfer was complete but after an ample amount of time closed the tunnel from my end, re- established my vpn but when i went to log in i received: RV082 firmware upgrade error? The requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist./quotei googled it and found similar occurrences with earlier upgrades. I'm assuming it didn't reboot itself upon completion of the xfer, at least i'm hoping a cold reboot will correct this but as i'm remote and this install doesn't have an ethernet power controller i'm stuck until monday. Should i bring a spare RV082 just in case.
View 3 Replies
View Related
Feb 5, 2013
I have a problem with a brand new RV042 v3 hardware,I upgraded the firmware from 4.1 to 4.2 and now can not see the web interface in firefox, the login appears and the left menu appears, but at the right nothing is shown
I tried doing the firmware rescue util but the same problem happens.if this a know issue? Should I RMA it?
View 2 Replies
View Related
Nov 6, 2011
I am unable to upgrade the firmware on the SRP546W
The admin guide states goto Administration > Firmware Upgrade > Choose File > Browse > Click Upgrade
There is no such item to select in the Administration section All I have in the administration section is
Remote Management
Time Setup
User
Also was wondering if it is possible to change the Annex B version I have to Annex A if I bring it back to England?
View 3 Replies
View Related
Mar 25, 2013
I am trying to update my firmware from v1 to v2 on my F5D9231-4 Router, after downloading from the support page and trying to install it I get the following error "Upgrade file is not the correct type or version for this device. Upgrade failed. Please obtain the correct file and try again" I double checked the model numbers.
View 2 Replies
View Related
Dec 30, 2012
F5D8233-4 N Wireless Router - Firmware Update,l I am trying to upgrade the firmware of this router which currently it's 3.01.29 to the latest one which is 4.00.04 but every time I try to manually install it, it comes back with an error message saying it's not the tight update but it is.
View 1 Replies
View Related
Jan 31, 2012
After upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites. In some instances, when the page does load, it lacks many graphics. Frequently, I also receive a "server not found"error. In all cases, reloading the page (once it has loaded) results in a complete page display. This is occuring on two MacBook Pros and also on an iPad. The router is a version 1, so no further upgrades are available. I contacted support, but since it is out of warranty, they are unwilling to assist. Prior to the upgrade, everything worked fine, as it has for 5 years.
View 1 Replies
View Related
Dec 13, 2012
We have a CISCO RV042. We are about to begin a VIOP service with Vocalocity who state:
The RV042 is a wired router that requires no configuration adjustments for the firmware versions we tested. Version 1 and 2 are compatible. Version 3 is NOT. Firmware Reviewed: 1.3.12.6 | 1.3.12.19
Our router's firmware is : 1.3.8.2 (Feb 12 2007 10:43:08)
Can we upgrade to 1.3.12.6 or 1.3.12.19? What is meant by Version 1, 2 and 3?
View 3 Replies
View Related
Jan 31, 2012
I've downloaded the file "RV0XX-v4.1.0.02-tm.bin" from Cisco's web site. The current firmware in the RV016 router is V3. I log into the router with IE9 (or even firefox), navigate to the system management section, upgrade firmware tab. Browse to the file above and click the button to upgrade. Nothing happens for a few seconds, then the browser displays cant load this page. (Same results if I use the file "RV0XX-v4.1.1.01-sp.bin" as well.)
View 1 Replies
View Related
Mar 10, 2013
I have a RV220W running 1.0.1.0. When trying to upgrade to 1.0.4.17 I receive an error: "Upgrade failed due to invalid/corrupted firmware".
I found this article: [URL]
I assume I have to do a factory reset then an upgrade in order to upgrade properly.
If I do a backup running 1.0.1.0, then upgrade to 1.0.4.17, then do a restore, would that put me back to 1.0.1.0? I'm trying to avoid configuring the router manually all over again.
View 1 Replies
View Related
Jan 31, 2013
I attempted a firmware upgrade on my RV042. After an hour, the upgrade was still in progress. I now cannot login into the router using my user name and password (nor the old admin/admin). The router is functioning, but I fear it will eventually fail. How can I recover ability to log in? The Firmward Recovery program doesn't seem to be appropriate for this situation.
View 3 Replies
View Related
Mar 19, 2013
I bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
View 2 Replies
View Related
Apr 17, 2013
if the SRP527W supports QOS over a site to site VPN.
SITE A will have the main phone system and SITE B will have a couple of phones which hook into the SITE A phone system over the existing IPSEC VPN
Need to be able to set some type of QOS over the VPN connection.
View 1 Replies
View Related
Mar 16, 2012
Is it possible to redirect all web traffic to a Symantec web filtering address on a particular listening port. I had a look at the Srp527w Router and can't find where this could be done.
View 1 Replies
View Related
Dec 17, 2012
I have a SRP527W router connected to a L2 managed switch (a TP-Link... I know, it is not a Cisco...). and a PC and a Printer connected to the switch. Now, I want to have the PC and the printer on 2 VLANs.
I've created 2 VLANs on the SRP (192.168.1.0/24 and 192.168.2.0/24) and I have assigned Lan port 1 to both. The SRP acts a DHCP server so I have the SRP setup as 192.168.1.1 and 192.168.2.1 providing IP addresses to the 2 VLANs.
I setup VLAN 1 and 2 on the switch, assigning port 2 to VLAN 1 and port 3 to VLAN 2 (port 1 is trunk and connects to the SRP).
When I fire up the PC and printer they get their respective VLANs correct addresses (PC: 192.168.1.30 and printer: 192.168.2.30) but I cannot for the love of Odin see the printer from the PC. The SRP has Inter VLAN routing enabled. By the way, the switch has address 192.168.1.2
View 8 Replies
View Related
Sep 12, 2012
I have a network which is based upon a 4507 Core/Dist switch, with 1G fibre to a bunch of radially connected 2960 Access switches. It all works fine and as expected for data and telephony.I have been tasked with setting up one of the VLANs to support multicast, so a bunch of video streams will be injected at the 4507, and will be delivered to client PCs connected to the 2960 switches.The 4507 is running with SVIs to some VLANs, but the VLAN that will have the Multicast on it is isolated, with no SVI.I could change this if required,I need to run IGMP snooping, and probably deploy CGMP to take advantage of the Cisco-proprietary functionaity.
View 4 Replies
View Related
Jun 5, 2012
I've got a new Cisco srp527w-u router which is working fine though it's syncing at a lower rate than my Billion (6mbps vs. 8.5 mbps for the billion on the same line). I had tweaked the billion way back to connect with a 4db SNR margin and almost certainly this is why it achieves the higher rate (by comparison the cisco is syncing with an snr margin of 12db). Is there some way that I can configure it to use a lower SNR margin? I realize this might reduce connection stability but I'd at least like to be able to give it a try if possible.
View 2 Replies
View Related
Jan 28, 2012
I recently bought a Cisco SRP527W and I'm trying to setup a second wireless network for guests.
I created a "guest" VLAN and I assigned the "guest" SSID which I have created.
I created a "guest" DHCP server and assigned it to the "guest" VLAN.
The "guest" SSID is set to broadcast and has WPA2 Personal (TKIP+AES) authentication. These are exactly the same settings I have for the "non-guest" WiFi.
However, I can't get my clients to connect to the network. The "guest" WiFi is visible and clients are prompted to enter the password but after that they end up with an APIPA address. When I move the "guest" SSID to VLAN1 (along with all the other networks) then it works absolutely fine.
I was just wondering if I'm simply missing something in the configuration ..
The device is running the latest firmware (1.01.24 (003) September 7, 2011)
DHCP server has DNS Proxy setting enabled and WAN Interface configured as "Default Route" (have basically replicated the same settings as VLAN1)
View 1 Replies
View Related
Apr 30, 2013
my client has just had the above router supplied by telstra and upon setup can no longer access filemaker server which was accessed prior on their netgear router. I have port forwarded to 5003 and 16000 as per the previous setup. Is there another setting somewhere that i am missing like perhaps static ip or something. I might add that networking is not my strong point.
View 7 Replies
View Related
Oct 21, 2012
I've just received a new SRP527W-U-E-K9 router to replace an old D-link router. However Apple IOS devices are not discoverable by iTunes on a Windows PC. The PC is connected to SRP527 by wired ethernet. All IOS devices are on the same SSID and the same VLAN as the wired ethernet devices.I have been reading on several other threads in this site about this exact same problem. The fault was that multicast broadcasts were not being forwarded between wired ethernet and WiFi on the same vlan. url...
The fault in thie above thread was resolved by a firmware update MR3 (v1.1.19) last year however it appears that the SRP527W-U has slightly different firmware to this version.The configuration of my SRP527 is the same as the original poster's config in the above thread. [code] The version information of my SRP is embedded below. As it is brand new, I assume that it is the most recent firmware, so I would have assumed that the bug which was resolved in the above thread above would be incorporated in this firmware version. [code] Is Cisco aware of this problem and is there any other firmware that I can load onto my model of SRP to resolve this?
View 1 Replies
View Related
Sep 16, 2012
I have a Cisco SRP527W at my remote office set up. I have configered a VPN connection to it. I installed Cisco VPN Client on my laptop.I can connect to the VPN but can not access the shared folders. I can ping the PC that has the shared folders. I take my PC and connect to the onsite LAN with WIFI, and I can now view the shared folders. I assume it must be somthing in the VPN set up that is blocking the shared folders from being seen. I also have disconnect all firewalls during testing at the remote end. I'am using windows 7 (64) on both PC's.
View 6 Replies
View Related
