I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1
View 5 RepliesI've downloaded the file "RV0XX-v4.1.0.02-tm.bin" from Cisco's web site. The current firmware in the RV016 router is V3. I log into the router with IE9 (or even firefox), navigate to the system management section, upgrade firmware tab. Browse to the file above and click the button to upgrade. Nothing happens for a few seconds, then the browser displays cant load this page. (Same results if I use the file "RV0XX-v4.1.1.01-sp.bin" as well.)
View 1 Replies View RelatedI am trying to upgrade my RV016 from 3.0.2.01-tm to 4.0.4.02. I have not received any messages and the log has nothing. I have left the computer and switch for 2 hours and it never seems to end. (serial no. DF0006200812).
View 1 Replies View RelatedI have an RV016 V3 with firmware 4.2.1.02 that is constantly rebooting making it unusable. I have one LAN connect and 3 WAN's, 2 DSL's and one Cable Internet in a load balance config. I have tried firmware 4.2.1.01 and it reboots also. do I get and RMA from Linksys and send this pig back?
View 6 Replies View RelatedI have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?
I've been having the lockup issue with the SRP527W (in fact this has been an extremely embarrassing situation after spending 4 x what I could have on a Net gear type unit, to do the same task). I've not yet managed to get hold of the new firmware (MR3) as I've not received the email with a link.
On another note, I'm not sure if this has been covered in other posts, but, when my unit stops working (Wireless still alive, no internet) - the CPU hits and stays at 100% and only a reboot fixes it.
I use cisco rvs4000v2. I had to restore the factory settings, and I use Cisco RVS4000 Firmware Upgrade Utility version 1.3. But I did not know that it is for Cisco RVS4000v1. The utility will install RVS4000 firmware v1.3.0.5. Now I can not restore to factory settings.how do I restore the factory firmware cisco rvs4000v2?
View 1 Replies View RelatedI just bought RV042G with serial number NKS16120688 to replace old RV042 which is cannot upgrade to new version firmware(from above V.4).After I connect to my TOT isp modem to new rv042g, the router distributes ip (DHCP), get dns from isp normally but it cannot connect the internet at all.It seems this new firmware is not compatible with tot isp in Thailand while old rv042 with old firmware can run smoothly.I have to try many things such as change wan port, change modem and also buy another new RV016, but results still the same.
View 1 Replies View RelatedI have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies View RelatedTried upgrading my firmware to 4.0.2.08-tm and now I cannot log in via the web interface. The router boots and gets out to the internet. It still allows incoming vpn connections. The login screen displays and will display an error message if I use incorrect credentials, but if I log in properly and am directed to the routers web config homepage at "192.168.1.1/default.htm", I get a 404 error message. Telnet does not work either (not sure if it's on, never used it before) 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.As if the web pages after the login screen got removed or corrupted after the update.
SN is NKS10403247
I realize there is a newer version. Attempted the upgrade incrementally since I could not find documentation specifiying if that was required or not.
Currently on V1.3.0.5. Looking to upgrade to latest version, however the upgrade firmware page is greyed out. Same under Firefox 9 or IE 8. I have already rebooted router, with no change in behavior.
View 2 Replies View RelatedI have upgrade the firmware on several RV082 (and RV042) model routers, and all of them have had subsequent WAN connectivity loss. The WAN works for a while, then stops working until the router is restarted, then fails shortly thereafter. I would assume it was some configuration corruption on incompatibility with the upgrade, but the symptom has been universal. EVERY 2.x upgrade I've made to a RV082 or RV042 router has exhibited this symptom. Reverting to the 1.3.98-tm firmware fixes the issue.
View 14 Replies View RelatedThis morning i upgraded a remote RV082 to 4.2.0.1 from 4.0.4.1. Numbers could be off slightly since i'm going from memory. I never got the normal acknowledgement the transfer was complete but after an ample amount of time closed the tunnel from my end, re- established my vpn but when i went to log in i received: RV082 firmware upgrade error? The requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist./quotei googled it and found similar occurrences with earlier upgrades. I'm assuming it didn't reboot itself upon completion of the xfer, at least i'm hoping a cold reboot will correct this but as i'm remote and this install doesn't have an ethernet power controller i'm stuck until monday. Should i bring a spare RV082 just in case.
View 3 Replies View RelatedI have a problem with a brand new RV042 v3 hardware,I upgraded the firmware from 4.1 to 4.2 and now can not see the web interface in firefox, the login appears and the left menu appears, but at the right nothing is shown
I tried doing the firmware rescue util but the same problem happens.if this a know issue? Should I RMA it?
I am unable to upgrade the firmware on the SRP546W
The admin guide states goto Administration > Firmware Upgrade > Choose File > Browse > Click Upgrade
There is no such item to select in the Administration section All I have in the administration section is
Remote Management
Time Setup
User
Also was wondering if it is possible to change the Annex B version I have to Annex A if I bring it back to England?
I am trying to update my firmware from v1 to v2 on my F5D9231-4 Router, after downloading from the support page and trying to install it I get the following error "Upgrade file is not the correct type or version for this device. Upgrade failed. Please obtain the correct file and try again" I double checked the model numbers.
View 2 Replies View RelatedF5D8233-4 N Wireless Router - Firmware Update,l I am trying to upgrade the firmware of this router which currently it's 3.01.29 to the latest one which is 4.00.04 but every time I try to manually install it, it comes back with an error message saying it's not the tight update but it is.
View 1 Replies View RelatedAfter upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites. In some instances, when the page does load, it lacks many graphics. Frequently, I also receive a "server not found"error. In all cases, reloading the page (once it has loaded) results in a complete page display. This is occuring on two MacBook Pros and also on an iPad. The router is a version 1, so no further upgrades are available. I contacted support, but since it is out of warranty, they are unwilling to assist. Prior to the upgrade, everything worked fine, as it has for 5 years.
View 1 Replies View RelatedWe have a CISCO RV042. We are about to begin a VIOP service with Vocalocity who state:
The RV042 is a wired router that requires no configuration adjustments for the firmware versions we tested. Version 1 and 2 are compatible. Version 3 is NOT. Firmware Reviewed: 1.3.12.6 | 1.3.12.19
Our router's firmware is : 1.3.8.2 (Feb 12 2007 10:43:08)
Can we upgrade to 1.3.12.6 or 1.3.12.19? What is meant by Version 1, 2 and 3?
I have a RV220W running 1.0.1.0. When trying to upgrade to 1.0.4.17 I receive an error: "Upgrade failed due to invalid/corrupted firmware".
I found this article: [URL]
I assume I have to do a factory reset then an upgrade in order to upgrade properly.
If I do a backup running 1.0.1.0, then upgrade to 1.0.4.17, then do a restore, would that put me back to 1.0.1.0? I'm trying to avoid configuring the router manually all over again.
I attempted a firmware upgrade on my RV042. After an hour, the upgrade was still in progress. I now cannot login into the router using my user name and password (nor the old admin/admin). The router is functioning, but I fear it will eventually fail. How can I recover ability to log in? The Firmward Recovery program doesn't seem to be appropriate for this situation.
View 3 Replies View RelatedI bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
View 2 Replies View RelatedI would like to ask if what is the replacement for RV016? Is there any on the ISR G2 that can be set as a mulit-WAN router? Meaning can handle for more than two WAN connections.
View 2 Replies View RelatedI have a rv016 that's been in 24x7 operation since I bought it a few years back. It is out of warranty. It is connected to three cable modems on WANs 1-3. Behind it are a bunch of PCs getting IPs via DHCP. There is a gateway to gateway vpn tunnel setup on wan3 to a rv082 at another site. There is a forwarding entry for http to an internal http server. Everything else is pretty much default.
The router is primarily used to aggregate bandwidth for uploading large numbers of photos. The systems behind the router initiate the uploads and the router automatically load balances the outgoing bandwidth.
This was all working fine until just recently. The ISP is Knology who is upgrading each of the 8m/768k cable modems to 25m/5m. They are also moving from DOCSIS 1 to DOCSIS 3. They are currently in the middle of this upgrade and have upgraded the modems to DOCSIS 3 as well as the speeds to 12m/2m. The problem is that the rv016 Network Service Detection, which is set to "Default Gateway" indicates that the modems fail randomly. Usually only one will be failed, but up to two will fail the Network Service Detection simultaneously.
Knology insists that there is nothing wrong with their modems. I have removed a modem from the rv016 when Network Service Detection indicates it is in a failed state and connected it directly to a computer. It will work, but it has a different IP address and default gateway. As soon as I connect it back to the rv016, it works there too, but on the original IP address and gateway. I've only tried this test this twice so far, so it is a bit inconclusive.
Speed tests behind the rv016 are the same as directly connected to one of the cable modems. The router works normally as it has for years. Nothing else is acting funny.
So my question is, is the rv016 failing or is the ISP having problems?
Problems on RV016 the firmware, Firmware Version : v4.2.1.02 (Jan 18 2012 14:10:55) on port PPPoE mode. It makes the dial, but not Web browsing correctly. The solution was to return the old version of firmware.
View 1 Replies View RelatedIs it possible to have this setup on RV016?
WAN1: VOIP traffic (either by port or IP) + failover for WAN 2 WAN2: all other traffic + failover for WAN1 WAN3: failover for WAN1 & WAN2 with connection on demand
I have hardware version 2 and firmware 3.0.2.01 (latest firmware available for this hardware version I believe) and I cannot get it to email me logs. I have entered my outlook address and our SMTP server.The log says that it's failing each time it attempts. I have scoured the internet and I cannot find a solution that will work for me. I have found some talk of adjusting an MTU setting which is supposed to be located under the firewall / general tab.
View 1 Replies View Relatedthis router (RV016v3, Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18)) in regards to it not properly directing UDP packets out of the right WAN, as per the settings stored in Protocol Binding section of [System Management, Multi-WAN].I use the section to direct all traffic from desktop computers (192.168.5.100 ~ 192.168.5.199) through WAN4, and all VoIP related traffic (192.168.5.200 ~ 192.168.5.239) through WAN2(PPPoE).Everything seems to be working well except for some of the UDP traffic from 192.168.5.200 which is seen in the log going out of WAN4 instead of WAN2.I have even created a new entry for [UDP/5060~5060]->192.168.5.200~192.168.5.200(0.0.0.0~255.255.255.255)WAN2, and placed it at the very top of the list.Here are a few lines that I've observed in the log: (Refreshed the registration of two SIP Trunks configured in our PBX)
Feb 23 18:11:47 2012 Connection Accepted UDP 192.168.5.200:5060->184.72.227.214:5060 on eth4
Feb 23 18:11:46 2012 Connection Accepted UDP 192.168.5.200:5060->50.56.59.168:5060 on ppp2
Feb 23 18:11:46 2012 Connection Accepted UDP 192.168.5.200:5060->184.72.227.214:5060 on eth4
Feb 23 18:11:46 2012 Connection Accepted UDP 192.168.5.200:5060->50.56.59.168:5060 on ppp2
There are no static routes configured, so i'm baffled by what could cause some of the UDP packets to go through the wrong WAN.All TCP Traffic from 192.168.5.200 is seen going though WAN2 as it should.
Would one of the 'Cisco RV016' work with a switch? I'm planning on running our work network using this device to load balance between 3 WAN connections and would like to keep the upstairs and downstairs computer users separated via a switch.Will the switch affect the load balancing or will the router still be able to detect each individual user and balance the load as seen necessary?
View 7 Replies View RelatedWe are deploying a new batch of RV016 with the latest firmware (4.0.4.02). We are using 3 WAN ports for internet access (WAN1, WAN2, WAN3)The WAN ports connects to Cicso 800 series adsl modem with DHCP.The RV016 WAN1 port setting regularly resets to 0.0.0.0 despite that the modem dhcp is still up and running. A cold boot, resets all the configuration and WAN1 port start working againg a new ip.
All three WAN ports are set to automatically obtain ip from the modems.We have tried several modems, and even swap WAN ports, but the error is persistant to WAN1 only.
WAN2 and WAN3 are up and running without any errors. This error is persistant with WAN1 only.We have also configured a manual ip on WAN1, and after a few hours of operation on all 3 ports, traffic on WAN1 comes to a halt.We have the same error on 3 units we received last week.All there modem are configure on different subnets.It does not seems to be a configuration error with the modem as they work perfectly well with the WAN2, WAN3 ports.We also tested a RV016 out of the box using the wizard setup, without any extra setting/configuration, and we got the same error after a few hours of operation.
I know this is a small business appliance I got my ccna certification with the hope of practice my CLI skills with a cisco device however I read in cisco docs the small business routers doesn´t support talnet neiter ssh I mean CLI, is thta true ?
View 1 Replies View Related