Currently on V1.3.0.5. Looking to upgrade to latest version, however the upgrade firmware page is greyed out. Same under Firefox 9 or IE 8. I have already rebooted router, with no change in behavior.
View 2 RepliesI have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies View RelatedI've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?
I am unable to upgrade the firmware on the SRP546W
The admin guide states goto Administration > Firmware Upgrade > Choose File > Browse > Click Upgrade
There is no such item to select in the Administration section All I have in the administration section is
Remote Management
Time Setup
User
Also was wondering if it is possible to change the Annex B version I have to Annex A if I bring it back to England?
I have a RVS4000 that will not save any settings. Click on, for instance, Disable WAN requests. Click save and it goes back to Enable.If I create a VPN tunnel, click save, it clears all settings like I didn't type anything.
View 11 Replies View RelatedHave the DIR-655 Hardware Version A1. Firmware 1.00NA dated Feb 2010. When I try to upload ANY firmware update from the DLINK site, it says that it is not for that device or is corrupt.
View 5 Replies View RelatedI have a DIR-615 Ver. C1 f/w3.00. We have been having trouble with the the signal becoming weak or non-existent, so I decided to see if a firmware upgrade would solve the problem. I have attempted to upgrade to DIR615C1C2_FW301B11.bin and to DIR615C1_FW313NAB09.bin with the same result for both of them - with several attempts for each.
The message I get is: "The uploaded firmware file may not be correct. You may have uploaded a file that is not intended for this device, or the uploaded file may be corrupted.
If the uploaded file is correct, it is possible that the device may be too busy to properly receive it right now. In this case, please try the upload again. It is also possible that you are logged in as a 'user' instead of an 'admin' - only administrators can upload new firmware.
The Gateway will not be reprogrammed."
I have disconnected all other devices to reduce traffic, I have attempted the upload multiple times for 3.01 and 3.13NA, I am logged in as the admin, and I believe the files are proper for this hardware version.
Is there something I am missing that prevents me from performing a firmware upgrade?
I am trying to setup the VPN access using QVPN with RVS4000 but ran into difficulties I was able to connect to the router using QVPN from WAN, and able to access the router's admin page (my router's ip is 192.168.0.1). However, I am unable to access anything else on the LAN, including servers and printers. To make it clear, I am able to access all servers and printers when I am on the LAN! But nothing when accessing from the WAN via QVPN.
View 1 Replies View RelatedJust a few weeks ago I purchased a rvs4000 router. On that small business device is a product called protectlink. To get an activation key, you need a registration key first. That is normal in the package. However, my wify like to cleanup up and throws stuff away that she should not do. So, I lost the registration key.
It is impossible to key a new registration key. The webstore does not have them. They are in the package and will not open an other one. Cisco (if you can get passed the ...you don't have a support contract...go away statement) does not even know that they have this product. Registration keys, never heard of it. But you get the normal ... go to the webstore or trendmicro.... And that after the statement, we don't know that product. How do you know that this is a trenmicro piece of software.....
getting a registration key for a cisco small business router rvs4000 to obtain an activation code for the cisco/trensmicro protectlink product.
RVS4000 setup at our office. QVPN installed on home pc with Win7 Home Edition and Norton Internet Security 2011. It gets the following error:
"The remote gateway is not responding. Do you want to wait? "
QVPN version 1.4.2.1, RVS4000 router firmware updated from V2.0.0.3 to the latest V2.0.2.7 as it is the Version 2 Hardware. Same problem. I even uninstalled the Norton NIS 2011, rebooted the machine and enable win 7 firewall without any anti virus software installed, same error. I really need this working as I do a lot of work at home and need remote connection to my computer at work.
Below is the error log...
2011/09/25 21:32:01 [STATUS]OS Version: Windows 7
2011/09/25 21:32:01 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/25 21:32:01 [STATUS]Windows Firewall Private Profile Settings: ON
[Code].....
I am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller. i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230 and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and the tftp client to no avail
the error i get on the wlc is Code file transfer failed - Error while writing output file
Firmware downloaded, FW_WRT120N_1.0.06.001_US after pressing APPLY nothing happens after few minutes it says. "There is an error in the Content-type field. Click the Back button to return to the previous page and re-enter the information."
View 2 Replies View RelatedRegion : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120607
ISP : Airtel[/COLOR]
I have wifi connectivity issues. After continues usage the wifi connection fails suddenly. And doesn't work till I restart it.
I have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1
View 5 Replies View RelatedI've been having the lockup issue with the SRP527W (in fact this has been an extremely embarrassing situation after spending 4 x what I could have on a Net gear type unit, to do the same task). I've not yet managed to get hold of the new firmware (MR3) as I've not received the email with a link.
On another note, I'm not sure if this has been covered in other posts, but, when my unit stops working (Wireless still alive, no internet) - the CPU hits and stays at 100% and only a reboot fixes it.
I use cisco rvs4000v2. I had to restore the factory settings, and I use Cisco RVS4000 Firmware Upgrade Utility version 1.3. But I did not know that it is for Cisco RVS4000v1. The utility will install RVS4000 firmware v1.3.0.5. Now I can not restore to factory settings.how do I restore the factory firmware cisco rvs4000v2?
View 1 Replies View RelatedI just bought RV042G with serial number NKS16120688 to replace old RV042 which is cannot upgrade to new version firmware(from above V.4).After I connect to my TOT isp modem to new rv042g, the router distributes ip (DHCP), get dns from isp normally but it cannot connect the internet at all.It seems this new firmware is not compatible with tot isp in Thailand while old rv042 with old firmware can run smoothly.I have to try many things such as change wan port, change modem and also buy another new RV016, but results still the same.
View 1 Replies View RelatedI have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies View RelatedTried upgrading my firmware to 4.0.2.08-tm and now I cannot log in via the web interface. The router boots and gets out to the internet. It still allows incoming vpn connections. The login screen displays and will display an error message if I use incorrect credentials, but if I log in properly and am directed to the routers web config homepage at "192.168.1.1/default.htm", I get a 404 error message. Telnet does not work either (not sure if it's on, never used it before) 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.As if the web pages after the login screen got removed or corrupted after the update.
SN is NKS10403247
I realize there is a newer version. Attempted the upgrade incrementally since I could not find documentation specifiying if that was required or not.
I have upgrade the firmware on several RV082 (and RV042) model routers, and all of them have had subsequent WAN connectivity loss. The WAN works for a while, then stops working until the router is restarted, then fails shortly thereafter. I would assume it was some configuration corruption on incompatibility with the upgrade, but the symptom has been universal. EVERY 2.x upgrade I've made to a RV082 or RV042 router has exhibited this symptom. Reverting to the 1.3.98-tm firmware fixes the issue.
View 14 Replies View RelatedThis morning i upgraded a remote RV082 to 4.2.0.1 from 4.0.4.1. Numbers could be off slightly since i'm going from memory. I never got the normal acknowledgement the transfer was complete but after an ample amount of time closed the tunnel from my end, re- established my vpn but when i went to log in i received: RV082 firmware upgrade error? The requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist./quotei googled it and found similar occurrences with earlier upgrades. I'm assuming it didn't reboot itself upon completion of the xfer, at least i'm hoping a cold reboot will correct this but as i'm remote and this install doesn't have an ethernet power controller i'm stuck until monday. Should i bring a spare RV082 just in case.
View 3 Replies View RelatedI have a problem with a brand new RV042 v3 hardware,I upgraded the firmware from 4.1 to 4.2 and now can not see the web interface in firefox, the login appears and the left menu appears, but at the right nothing is shown
I tried doing the firmware rescue util but the same problem happens.if this a know issue? Should I RMA it?
I am trying to update my firmware from v1 to v2 on my F5D9231-4 Router, after downloading from the support page and trying to install it I get the following error "Upgrade file is not the correct type or version for this device. Upgrade failed. Please obtain the correct file and try again" I double checked the model numbers.
View 2 Replies View RelatedF5D8233-4 N Wireless Router - Firmware Update,l I am trying to upgrade the firmware of this router which currently it's 3.01.29 to the latest one which is 4.00.04 but every time I try to manually install it, it comes back with an error message saying it's not the tight update but it is.
View 1 Replies View RelatedAfter upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites. In some instances, when the page does load, it lacks many graphics. Frequently, I also receive a "server not found"error. In all cases, reloading the page (once it has loaded) results in a complete page display. This is occuring on two MacBook Pros and also on an iPad. The router is a version 1, so no further upgrades are available. I contacted support, but since it is out of warranty, they are unwilling to assist. Prior to the upgrade, everything worked fine, as it has for 5 years.
View 1 Replies View RelatedWe have a CISCO RV042. We are about to begin a VIOP service with Vocalocity who state:
The RV042 is a wired router that requires no configuration adjustments for the firmware versions we tested. Version 1 and 2 are compatible. Version 3 is NOT. Firmware Reviewed: 1.3.12.6 | 1.3.12.19
Our router's firmware is : 1.3.8.2 (Feb 12 2007 10:43:08)
Can we upgrade to 1.3.12.6 or 1.3.12.19? What is meant by Version 1, 2 and 3?
I've downloaded the file "RV0XX-v4.1.0.02-tm.bin" from Cisco's web site. The current firmware in the RV016 router is V3. I log into the router with IE9 (or even firefox), navigate to the system management section, upgrade firmware tab. Browse to the file above and click the button to upgrade. Nothing happens for a few seconds, then the browser displays cant load this page. (Same results if I use the file "RV0XX-v4.1.1.01-sp.bin" as well.)
View 1 Replies View RelatedI have a RV220W running 1.0.1.0. When trying to upgrade to 1.0.4.17 I receive an error: "Upgrade failed due to invalid/corrupted firmware".
I found this article: [URL]
I assume I have to do a factory reset then an upgrade in order to upgrade properly.
If I do a backup running 1.0.1.0, then upgrade to 1.0.4.17, then do a restore, would that put me back to 1.0.1.0? I'm trying to avoid configuring the router manually all over again.
I attempted a firmware upgrade on my RV042. After an hour, the upgrade was still in progress. I now cannot login into the router using my user name and password (nor the old admin/admin). The router is functioning, but I fear it will eventually fail. How can I recover ability to log in? The Firmward Recovery program doesn't seem to be appropriate for this situation.
View 3 Replies View RelatedI bought belkin N150 recently. I tried to configure with my ISP. They are surprised how I don't have DHCP option in the wifi configuration and asked me to upgrade my firmware. When I tried to upgrade. I downloaded the firmware from [URL] tried to upgrade. It is showing file format error.
View 2 Replies View RelatedI am unable to isolate DMZ and LAN traffic with an SA520 running 2.1.7.1 firmware. I have the optional port configured as DMZ and DHCP server enabled. I tired leaving the firewall as default. Also tried creating firewall rules to deny traffic from LAN to DMZ and DMZ to LAN for any address and any service.I am still able to ping devices both from LAN to DMZ and DMZ to LAN. I am also able to see network resources in both directions.
View 5 Replies View RelatedI have recently acquired one of these routers. I thought, being a Cisco product, it would be the bee's knees. It is not. After finally getting the network set up - no mean feat, although I do not claim any expertise, but had to resort to some other network management software to finally get it all running - the router drops either the WAN connection or the wireless connection many times a day. The laptops often show as being connected to the network/router, but are unable to access either the internet, or the router via the browser. Re-booting the router is the fix, but, hey, I can achieve that sort of performance with any old $20 router - none of my old Net gear routers was this troublesome.
The permanent fix would seem to be a firmware upgrade, but guess what? The only options available under the "Administration" tab are time setting and switch settings - no firmware upgrade. The supplied firmware is 1.01.09(001) Apr 7 2010. Why these products are supplied, as new, without the latest firmware installed beats me, but there you go.