I have a RVS4000 that will not save any settings. Click on, for instance, Disable WAN requests. Click save and it goes back to Enable.If I create a VPN tunnel, click save, it clears all settings like I didn't type anything.
View 11 RepliesNothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies View RelatedIs there a way to avoid network interruptions when resetting the F5D8235-4 v3 router? I was hoping to find a config file or some other way to avoid having to reset the home network and devices. The administrator password has been lost, so i would like to reset that only and not restore factory settings.
View 1 Replies View RelatedRecently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies View Relatedwhy my device "cisco RVS4000" loses settings after some down time without electricity?
View 2 Replies View RelatedI have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies View RelatedI've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?
Currently on V1.3.0.5. Looking to upgrade to latest version, however the upgrade firmware page is greyed out. Same under Firefox 9 or IE 8. I have already rebooted router, with no change in behavior.
View 2 Replies View RelatedI got a new DIR-825 router and when I try to change settings such as the date and time or try to apply web filters my changes won't save.
View 2 Replies View Relatedwhy I can't save any router settings? I get a momentary disconnect followed by a brief redirect message and then I get kicked back to the router log on page. This just started happening.
View 3 Replies View Relatedwhy I can't save any router settings? I get a momentary disconnect followed by a brief redirect message and then I get kicked back to the router log on page.
View 3 Replies View RelatedDue to problems with the D view cam, I have reset my IP camera DCS-930L but I can't register the password, it says "There was a problem saving your settings. Press next and try again." I can't get pass saving password, tried all the previous passwords but none works.
View 2 Replies View RelatedI try to change modem speed from 1200 to 19200 on aux 0 interface.But I can't save the settings using "write memory" In show running-config, I can see modem speed successfully changed.
Cisco3825's OS information is here. c3825-spservicesk9-mz.124-25b.bin
Save and reset button is not working on Sys log Purge Settings page (Admin > Network > Purge Settings > Sys log Purge Settings) when Email: field is not empty. An Reset button is not working at all.This is the Cisco Prime LMS 4.2.1.
Is it only my LMS server or you all have this bug?
I'm just trying to port forward with this router, and after I'm done entering all my settings, I click save settings, it tells me settings are successful.
But the it goes back to the port forwarding page and all the stuff is at default again as if I didn't make any changes. What the hell is this?
I'm sure it's just a little something I don't know about that's making it not save any changes to port forwarding.
just bought DCS-930L few days ago, the manual sounds so easy (but it's hard than it looks) i stuck on the setting-up, here is my problem: unable to connect to mydlink web site and there was a problem saving my settings. seems like internet connecting problem, the software just couldn't connect to internet.i have already registered, i got my device number and it couldn't be find in my device on mydlink.
View 5 Replies View RelatedI upgraded the firmware per one suggestion, but no difference.I am going thru the setup wizard with ethernet cable attached. I want to use them wirelessly so I clicked wireless setup, and entered my network info. At that point I get an error message saying it failed to save settings. I know the ID and password are correct.I have tried exiting the setup wizard and accessing the camera thru the web interface. All wireless settings are correct. The camera works FINE on web browser, myDlink, and even my iPhone app as long as the ethernet cable is attached.Other wireless devices have no trouble connecting to my router. Is there some setting on the router that can be preventing the connection? I've done some trial-and-error changes, like different ports and enabling/disabling UpNp on both camera and router.Oh and almost forgot to mention.I did call tech support, which was a joke. Some foreign lady was reading off a script that told me to reset, unplug, reboot everything. Then she gave me a case# and said upgrade the firmware.
View 11 Replies View Relatedi am trying to port forward my router so that i can run a minecraft server. When I put in th port number and save the changes, it brings me to a screen that says my changes have been saved yet when i go back to the page they haven't. I have tried deleting the cookies on my browser, using another browser, using another computer, and hard resetting the router for ten seconds. None of this works.
View 2 Replies View RelatedI did read the thread entitled ''WRT160N Can't save settings'', but I believe this might be different. My router is actually communicating with my computer (physically plugged in), since I can save all other settings EXCEPT the port-fowarding ones.I am trying to save settings for a gaming application in the Single Port Forwarding section of my router settings. After clicking both ''save settings'' and ''continue'', it simply returns to the Single Port Forwarding section, except everything is blank, as though nothing was saved.
Here are my specs:
WRT160Nv1
Firmware Version: v3.0.03
Here are the steps I have already undertaken:
1- Erase browser cache and cookies
2- Updated to latest firmware (v3.0.03), 10-second reset button, 20-second power cycle.
I use a BEFVP41 VPN router. I have changed several settings. How can I backup these settings and store these settings in a save place.
View 3 Replies View RelatedFor some reasons, my internet connection keeps dropping more often recently. My laptop still says it is connected to my network but I can just not have internet connection. It was not like that before but it happened more frequently now. What I did was to power off then on the modem and the router and everything will work fine again. I want to upgrade my firmware but I just wonder if I need to save all the configuration before doing the upgrading? If so, then how can I set it back to the old configuration that was saved?
View 5 Replies View RelatedI just installed my new E4200, and am setting the Access Restrictions. Is there anyway to block the popup window that displays every time I enter the form or save the settings?
I'm using IE9 and have tried adjusting the Popup Blocker, but to no avail.
How to set up RVS4000 QOS settings to work with a VOIP phone system? I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection.
View 1 Replies View RelatedI have 2 internet connections in my office one via Verizon Fios and another one via the local cable company. On the fios connection I have an RV042 VPN router and on the Cable company connection I have an rvs4000 router, I would like to know if there is a way I can connect the 2 so I can share a printer I have on one of the 2 networks from the other network without using the VPN feature, like via an ethernet cable connected between the 2 and some kind of static route maybe?
View 6 Replies View RelatedI've been lagging really bad when my sister uses the laptop upstairs with wireless connection. Just 1 computer makes me have up to 100 ping, imagine 3. How can configure my settings so that i will stop lagging or configure so that i have priority.I have a Dlink 655 Version A4 with the latest firmware 1.35
View 9 Replies View Relatedi have Aztech DSL605EW wireless modem. I updated its firmware on some philipines Globle Broadband network's firmware. Now the problem is to open its configration I have to use 192.168.254.254 IP and the configuration settings are very limited and there is no option of updating firmware in it. I am stuck with it.
View 3 Replies View RelatedI have a Linksys E3000 router, which originally had all sorts of security settings, and names for the wireless networks, etc. It was all set up. I upgraded the firmware, and all of those settings sent away. Is there a way to reconfigure the settings to get them back to how they were, and if so, how do I do it?
View 2 Replies View RelatedI just flashed this router with DD-WRT about a week ago inside the webui that was provided. It all went well but I wanted to go back to the original factory firmware so turned it off for 20 seconds, and held the reset button for 10 seconds to reach the emergency-room. I re-flashed it with the firmware I got from d-links website and all went well. So I tried to go to 192.168.0.1 that did not work so I tried the ip that I gave it before it was flashed and it still remained x.x.x.254. I also turned off dhcp server since my isp's modem provides that and other services. But when I looked into the logs it would keep starting up dhcp server every minute which would lead to all kinds of problems.
Edit: The ip/subnet are set to 192.168.0.1/255.255.255.0. It seems to start this as soon as dhcp is disabled.
LOG:
11:56:02 device_lan_ip=, device_lan_subnet_mask=
11:56:02 DHCP Server Start
11:55:51 device_lan_ip=, device_lan_subnet_mask=
11:55:51 DHCP Server Start
11:55:40 device_lan_ip=, device_lan_subnet_mask=
11:55:40 DHCP Server Start
Hardware Version listed in the webui: _auth_m
I currently have this router in use with verizon dsl (PPPoe) setup.I have this set to "always on". Since the verizon modem, which is also router has been set into bridge mode and the d-link came into play its been extremely slow, and dropping connection. The router is in a separate IP class, and has no conflict with the modem. My question is, if I upgrade this firmware from 1.0 to 1.02 will it default to factory settings? I know it says only some will. I do have the backup config file, but i would be doing this remotely, and would not be able to get to this router if it goes down. Has anyone gone from 1.0 to 1.2 and saw a difference and speed, and are you able to do this without losing settings.
View 3 Replies View RelatedWith firmware version 1.31, the Wireless settings page is blank when a browser other than Internet Explorer is used to access it - for instance, Firefox or Chrome.All other pages appear and seem to work properly, only the Wireless settings page is empty. Luckily, the Wizard still works and can be used to set the Wireless settings for general purpose use. Older versions of the firmware worked fine with other browsers, including the Wireless settings page.
View 6 Replies View RelatedI was trying to set a DHCP pool with 127.16.0.0/16 with RV220W, however, RV220W UI can't save it. It displays "IP Address Range -"Step to reproduce: (it is 100% reproducible)
1. login into RV220W admin web
2. Create a VLAN, id 201
3. Go to "Multiple VLAN subnets", select the VLAN, click edit
4. Enter following info:
IP Address: 172.16.0.1
Subnet Mask: 255.255.0.0
DHCP Mode: DHCP Server
Domain Name: Cisco
Starting IP Address: 172.16.2.100
Ending IP Address: 172.16.10.254
Primary DNS Server: 172.16.0.1
Leave rest of settings with default value.
DNS proxy is enabled
5. Press Save button. The UI shows text "IP Address Range -".
Expected result: RV220W shall save the setting and make use of 172.16.0.0 subnet in IP pool. By the way, the error message "IP Address Range -" seems incompleteI tried same setting on netgear FVS318N (very similar settings to RV220W), it accepts 172.16.0.0/16 as DHCP IP pool and works.RV220W has great feature set meets my needs. Its UI is slow and sometime dashboard freezes, which I can live with comparing to features. But DHCP server IP pool can't be class B is huge limitation to me.
This firmware bad, because my sync program, can't set create date of files on external usb storage connected to router, on 1.0.04 - all good.
View 5 Replies View RelatedIve set up a rvs4000 with two vlans, one as a bussiness network and the other as a guest network. Everything works fine and the networks can not see each other. I would like to add wifi and I would like to do so with keeping both networks separate. I have a used 1130AG access point and was wondering if I could use this single AP for both networks. If so, how would I go about doing so? Is there a better suited AP for my needs?
View 4 Replies View Related