How to set up RVS4000 QOS settings to work with a VOIP phone system? I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection.
View 1 Replies
A broadband cable modem is connected to the input of a new BEFSR41 4-port router. The router feeds 4 computers (a newer "primary" PC, and 3 secondary "old goats" that I use to print online grocery coupons). The 4 PC's are networked to share a common printer, a single directory on the "primary" PC, and using a 4-port KVM switch - I switch a single keyboard and mouse to whichever PC that I am using at the time.
View 1 Replies View RelatedI have a VOIP WiFi phone (MIC505W) I have configure it according to the user manual.I get access to WiFi, but when I dial a number I get busy signal with the message "disconnet".
View 3 Replies View RelatedI buy new Linksys RT341P2 router with Linksys - Firmware Version: 1.30.01. My voice ports are locked, and i can`t use voip providers. How to unlock and what i need to do?
View 1 Replies View RelatedI have a strong internet signal with good SNR coming out of my cable modem, then a nice short 3ft cable going to my linksys VOIP router (I think it's a SPA 2102). Whether I have anything downstream plugged in or not, the "phone" light on the VOIP router goes off every once in a while and when I check I find that I've lost both dial tone and Internet - basically everything downstream of the VOIP router. Have tried every variation on configuration you can imagine (feeding just one phone, feeding the entire phone wiring to the house, nothing at all plugged into the phone jack, no computers downstream plugged in, replaced all the cables, ...). I've replaced BOTH the cable modem and the linksys VOIP router and the problem continues. My cable company says my signal is fine. They suggested a signal amplifier but the coax comes straight to the modem, no splitter, and I'm always seeing 6-7dBmV. My phone company says their router must be losing signal upstream and refusing to reconnect, especially now that we've tried replacing their VOIP router with no change. Any chance I got two 'bad' routers in a row? Not sure what they did for setup parameters. I'm not particularly tech-savvy but have read a lot since seeing these issues, have run my own ping and tracert checks and everything seems to be wonderful... but then most of the time everything IS fine. When I have phone it's crystal clear and when I have internet it's nice and fast. I sometimes go 24hrs or so without a drop, but other times I'm resetting 2-3x in a couple of hours. All I do is power off the VOIP router and back on and everything is fine, for a while. After first getting VOIP things were fine for 4-6 weeks.
View 1 Replies View RelatedI have a new Polycom Soundpoint IP550 VOIP phone that was not connecting via my old WRT54GS router. I purchased a new router, the E4200, thinking it was just the age of my original router. It also will not allow the VOIP traffic through. I can connect the VOIP phone directly to my CenturyLink modem and it works. But when I connect it back to the router it stops.
I contacted Cisco support and they had me upgrade the firmware to 1.0.02 build 13 May 24, 2011 version. Also adjusted down the MTU to 1364. That still did not work so they told me to take the router back to the store. I have not done that yet as I want to ensure that the router is really broken and not that I am missing a setting. The tech said that I should be able to plug the VOIP phone into the router and make NO additional changes.
I just installed an RVS4000 router for a SOHO. I have no problem getting out to the internet so access from LAN -> WAN is working fine. The problem is with VPN access from the WAN.I created a VPN account and set up QuickVPN on a PC making sure I imported the certificate. I can connect to the router with no problem and I can even connect to the routers web admin page.But that's where it ends. I cannot connect in any way, shape, or form to PCs on the LAN through the VPN. I can't even ping them.Am I missing something in the setup of the router?
This is the only reason I bought this router as the old one was working fine. How to fix getting through the router to connect to the computers on the LAN.
after using BEFSR41 for a long time without any problems, I decided to buy a new router RVS4000 to be able to have gigabit connections.
The problem is when I download a youtube video or I use VPN or even a desktop remote access, it always disconnect. I've seen many and many posts on this forum of people having this problem, I decided to try what you suggested to them:
- Changed the MTU to 1492
- Disabled IPS
- Disabled Firewall
- A couple of other things
- I already have the latest firmware
... and i've done some other tests in my side but nothing worked so far, just like for those who had this problem. I strongly think it's a problem on the router and not a problem from the user.
I have an RVS4000 located at my office. A user of mine also has one at their house. We have created an IPSec Tunnel between the 2 of them and have them successfully communicating between the 2 networks with no problem.
The problem I have is if I make a change on their end and the router needs to reboot to apply the changes, the WAN port never renews it's DHCP address. The end user must unplug the unit, plug it back in and then the system comes back up with the correct WAN DHCP address, and the tunnel is connected automatically.
I beleive they have the newest firmware (2.0.0.3) but I cannot confirm that right now as the unit is down. I bought the 2 of them at the same time - my unit at the office has the 2.0.0.3 firmware so I am assuming the users does as well.
I have successfully configured my Cisco RVS4000 for VPN Access, and Installed QuckVPN on my client machine. I can connect using QuickVPN no problem, but I cant access anything on my network. When I try pinging any of my servers I am unable to do so. I can ping my gateway thats about it.
View 1 Replies View RelatedI have a PPTP VPN server (WIndows 2008 R2) sitting behind an RVS4000, I have port forwarding for 1732 on and the client's (Windows 7) can reach the VPN server but cannot complete the connection due to an 806 error, which is GRE traffic related. I have PPTP passthrough on and have also created a ACL entry for PPTP traffic. I've seen many posts on this topic over several years with no solutions, and I do have the latest firmware (Version:V1.3.3.5). This is also definetely router related as I have absolutley no problem connecting when I point directly to the VPN server by internal IP address.
View 1 Replies View RelatedWe share a common fibre connection to the internet. In the basement we have a modem/router(zyxel) which is in "bridge mode". Therefore not acting as DHCP.Behind this zyxel we have a Cisco RVS4000 router. Ports 1 and 2 go to family A, and Ports 3 and 4 go to family B.Family A and B have separate routers which are both set to "access point mode". Family A has an ASUS RT-N66U router while family B has a dlink DIR-615. The asus has an "access point mode" while the dlink needs to be set up manually to achieve this. The dlink must also have a static IP adress. The asus can receive ip adress.
View 1 Replies View RelatedI am trying to configure my RVS4000 to create my church's small network. I want to connect my internet DSL router on the WAN port and also segment my network with VLANs on the 4 LAN ports. I have port 4 connected to a wireless access point which is in VLAN1 for an open wireless network for any church member to access the internet through. I have a church server, printer and second access point on ports 1-3 in VLAN 34. All ports are untagged. I want the devices on VLAN34 which need confidentiality to be secure from the devices connecting to the internet from VLAN1 for open access but both VLANs need access to the internet..
My open wireless AP in VLAN1 has access to the internet on the WAN port.None of my devices in VLAN34 have access to the internet. I have tried using inter-VLAN routing but that made operation worse so I disabled it.
I've looked through the documentation that came with the router and there is no instructions on how to configure the 4000 to accept remote clients and access the local network. What the configurations are so a client can launch the vpn client, login, and remote desktop to their local workstations in the office? I don't have any tunnels or connections setup with other offices, just a simple client connection.Also, will the rvs4000 work with Cisco VPN client (comes with higher end appliances)?
View 1 Replies View RelatedHow to setup quickvpn to work with RVS4000.
View 9 Replies View RelatedJust purchased a RVS4000. How to be successfully able to VPN into this device from os/x? If so what software / settings required.
View 6 Replies View RelatedI have RVS4000 v02 and created 3 VLANs - 192.168.70.0/24, 192.168.80.0/24, and 192.168.90.0/24 . I tired to created IP based access list to deny network 192.168.80.0/24 and 192.168.90.0/24 to have access to 192.168.70.0/24; and deny 192.168.90.0/24 to access 192.168.80.0/24.
MY ACCESS LIST from RVS4000
Deny All Protocol LAN 192.168.80.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.80.0/255.255.255.0 Any Time Every Day
Allow All Service LAN ANY ANY Any Time Every Day
Allow All Service WAN ANY ANY Any Time Every Day
* all access list is enabled.Both 192.168.80.0 and 192.168.90.0 network can still reach 192.168.70.0 network.
I recently purchased a rvs 4000 wired linksys router for my business. Everything works great with the exception of my VOIP PBX server. I can receive a call and make a call one at a time. If a second line rings in and is picked up the first call and the second go dead air. I am sure that it is a security setting somewhere that I just can't seem to figure out. I sure would like to get some direction on this.
View 2 Replies View RelatedI am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000. I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.). I do not use DHCP as all the LAN units are static addressed. I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues. I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.
View 1 Replies View RelatedI connect to my RVS4000 VPN router using QuickVPN. Very useful.
Sometimes I am not near my laptop and need to check data.
Is there a QuickVPN or compatible client for a BlackBerry Torch 9850, even if it's only functional when connected to WiFi?
I am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies View RelatedDoes it support SSL VPN? As I would like to have secure web access without installing other software.
View 1 Replies View RelatedWe have used two Cisco RVS4000 to create the IPSec VPN between the main office and the branch office. The main office has SBS 2008. There is a Windows Server 2008 as the domain controller in the branch office. One branch office user has a laptop which is not in the domain, but his exchange account is set up in the Outlook. When he connects the laptop to the branch office network, he cannot connect to the exchange server and get the emails. Is there any configuration to set up in the router, server or Outlook?
View 1 Replies View RelatedI need properly configuring the RVS4000 device. I need all devices to be on the same subnet (192.168.0.x) and if I am drawing this out correctly in my head I would perform the following:Connect LAN port of RVS4000 to LAN port of the switch and statically assign a LAN IP of 192.168.0.251 to the RVS4000Switch is connected to LAN port of the 2Wire (192.168.0.254)Change operating mode from Gateway to Router in the RVS4000 Connections to the RVS4000 will obtain a DHCP IP address from the 2Wire that's upstream.As the WAN port of the RVS4000 would be unused, will it still answer requests for a VPN connection assuming the proper ports are forwarded to it?
View 1 Replies View RelatedIs there an alternate way to get the DNS settings off of the router? I've followed all of the steps up above, but I cannot set up a static IP Address on my computer without knowing the routers DNS settings, which I cannot retrieve from the web-based setup due to the corrupt firmware.
View 2 Replies View RelatedI recently bought a rtp300 and its on the 3.1.24 fw version I have been looking everywhere and i have not found any answer to my problem.It doesnt seem that you can change the pppoe settings (vpi,vci, encapsulation or PPP authentication ) anywhere. Should i return it If i apply the 5.01.04 i could those settings?
View 2 Replies View RelatedPurchased an EA4500 router. I'm using an old HP 4L laserjet and have it connected to the router via the USB port. I have 2 Mac's and installed vusb on both. I can successfully print from both Mac's, however I have to manually disconnect and connect the printer in the vusb client. I can't get the auto-connect and auto-disconnect settings to work by themselves. Any guidance on the proper settings here?Additionally, do I need to configure the printer driver though the vusb client? When I click "configure", I get an error saying"Cannot connect to Prolific Technology Inc. IEEE-1284 Controller.
View 3 Replies View RelatedI use a BEFVP41 VPN router. I have changed several settings. How can I backup these settings and store these settings in a save place.
View 3 Replies View RelatedIs it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies View RelatedI have a problem with RV042. My ISP gives me automaticly IP address and i had no problems using different types of routers, including linksys routers. With RV042 i just can't get the IP. It says, the port is up, i see the packets/traffic, front control light is blinking but it never receives the dhcp settings, doesn't matter if i use wan1, wan2, dual wan mode or single wan. I have the newest firmare 1.3.12.19tm. System statistics says "disconnected" but the packets come in and go out. Log shows absolutely nothing. I also disabled firewall but it didn't work. I can't seem to find the older 1.3.12.6 firmware.
View 7 Replies View RelatedI purchased Linksys WAG160N (from a store) and I also have 7 Linksys SPA962 VOIP phones provided by MyNetPhone with service included. All tests we found out that this modem doesn't work with this VOIP phones. Somehow probably doesn't give access to MyNetPhone servers to get connection with this phones.I purchased an other one from DLINK and works perfect?
View 1 Replies View RelatedI have just changed from cable to DSL. I have a LinkSys BEFSR41 router. I can't get my LinkSys BEFSR41 router to work with the DSL.
View 3 Replies View RelatedI have a DIR-825 since a couple of days, Hardware version B1, firmware 2.01EU (date Fri, 12, Jun, 2009 = latest european firmware) Have portforwarding for ports 25, 80, 443, 143, 993 via virtual server to a local linux server (192.168.0.3)
My (SIP protocol) VOIP phone (192.168.0.100) does not work anymore since I use this router. It worked fine on my old WRT54G. The phone logs-in normally at the voip provider but when I make a call, it seems that the ports are not forwarded or are blocked by the firewall. I have tried to manually setup portforwarding and virtual server instead of portforwarding.
I have tried many things, from disabling QOS, SPI, end point filtering and more but it does not work. I have also programmed DMZ for my ip-phone, but it does not work. Nothing found in the logfiles about frame drops. (I have setup a syslog on my linux-server)
There seems to be a bug causing frames dropped, as my setup has always worked with my WRT54, and should work with DMZ set, but it does not. The same setup works fine on a DIR-655 of a friend.
