I have successfully configured my Cisco RVS4000 for VPN Access, and Installed QuckVPN on my client machine. I can connect using QuickVPN no problem, but I cant access anything on my network. When I try pinging any of my servers I am unable to do so. I can ping my gateway thats about it.
View 1 Replies
I just installed an RVS4000 router for a SOHO. I have no problem getting out to the internet so access from LAN -> WAN is working fine. The problem is with VPN access from the WAN.I created a VPN account and set up QuickVPN on a PC making sure I imported the certificate. I can connect to the router with no problem and I can even connect to the routers web admin page.But that's where it ends. I cannot connect in any way, shape, or form to PCs on the LAN through the VPN. I can't even ping them.Am I missing something in the setup of the router?
This is the only reason I bought this router as the old one was working fine. How to fix getting through the router to connect to the computers on the LAN.
I am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000. I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.). I do not use DHCP as all the LAN units are static addressed. I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues. I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.
View 1 Replies View Relatedafter using BEFSR41 for a long time without any problems, I decided to buy a new router RVS4000 to be able to have gigabit connections.
The problem is when I download a youtube video or I use VPN or even a desktop remote access, it always disconnect. I've seen many and many posts on this forum of people having this problem, I decided to try what you suggested to them:
- Changed the MTU to 1492
- Disabled IPS
- Disabled Firewall
- A couple of other things
- I already have the latest firmware
... and i've done some other tests in my side but nothing worked so far, just like for those who had this problem. I strongly think it's a problem on the router and not a problem from the user.
I have an RVS4000 located at my office. A user of mine also has one at their house. We have created an IPSec Tunnel between the 2 of them and have them successfully communicating between the 2 networks with no problem.
The problem I have is if I make a change on their end and the router needs to reboot to apply the changes, the WAN port never renews it's DHCP address. The end user must unplug the unit, plug it back in and then the system comes back up with the correct WAN DHCP address, and the tunnel is connected automatically.
I beleive they have the newest firmware (2.0.0.3) but I cannot confirm that right now as the unit is down. I bought the 2 of them at the same time - my unit at the office has the 2.0.0.3 firmware so I am assuming the users does as well.
I have a PPTP VPN server (WIndows 2008 R2) sitting behind an RVS4000, I have port forwarding for 1732 on and the client's (Windows 7) can reach the VPN server but cannot complete the connection due to an 806 error, which is GRE traffic related. I have PPTP passthrough on and have also created a ACL entry for PPTP traffic. I've seen many posts on this topic over several years with no solutions, and I do have the latest firmware (Version:V1.3.3.5). This is also definetely router related as I have absolutley no problem connecting when I point directly to the VPN server by internal IP address.
View 1 Replies View RelatedWe share a common fibre connection to the internet. In the basement we have a modem/router(zyxel) which is in "bridge mode". Therefore not acting as DHCP.Behind this zyxel we have a Cisco RVS4000 router. Ports 1 and 2 go to family A, and Ports 3 and 4 go to family B.Family A and B have separate routers which are both set to "access point mode". Family A has an ASUS RT-N66U router while family B has a dlink DIR-615. The asus has an "access point mode" while the dlink needs to be set up manually to achieve this. The dlink must also have a static IP adress. The asus can receive ip adress.
View 1 Replies View RelatedI am trying to configure my RVS4000 to create my church's small network. I want to connect my internet DSL router on the WAN port and also segment my network with VLANs on the 4 LAN ports. I have port 4 connected to a wireless access point which is in VLAN1 for an open wireless network for any church member to access the internet through. I have a church server, printer and second access point on ports 1-3 in VLAN 34. All ports are untagged. I want the devices on VLAN34 which need confidentiality to be secure from the devices connecting to the internet from VLAN1 for open access but both VLANs need access to the internet..
My open wireless AP in VLAN1 has access to the internet on the WAN port.None of my devices in VLAN34 have access to the internet. I have tried using inter-VLAN routing but that made operation worse so I disabled it.
I've looked through the documentation that came with the router and there is no instructions on how to configure the 4000 to accept remote clients and access the local network. What the configurations are so a client can launch the vpn client, login, and remote desktop to their local workstations in the office? I don't have any tunnels or connections setup with other offices, just a simple client connection.Also, will the rvs4000 work with Cisco VPN client (comes with higher end appliances)?
View 1 Replies View RelatedHow to setup quickvpn to work with RVS4000.
View 9 Replies View RelatedJust purchased a RVS4000. How to be successfully able to VPN into this device from os/x? If so what software / settings required.
View 6 Replies View RelatedI have RVS4000 v02 and created 3 VLANs - 192.168.70.0/24, 192.168.80.0/24, and 192.168.90.0/24 . I tired to created IP based access list to deny network 192.168.80.0/24 and 192.168.90.0/24 to have access to 192.168.70.0/24; and deny 192.168.90.0/24 to access 192.168.80.0/24.
MY ACCESS LIST from RVS4000
Deny All Protocol LAN 192.168.80.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.80.0/255.255.255.0 Any Time Every Day
Allow All Service LAN ANY ANY Any Time Every Day
Allow All Service WAN ANY ANY Any Time Every Day
* all access list is enabled.Both 192.168.80.0 and 192.168.90.0 network can still reach 192.168.70.0 network.
I connect to my RVS4000 VPN router using QuickVPN. Very useful.
Sometimes I am not near my laptop and need to check data.
Is there a QuickVPN or compatible client for a BlackBerry Torch 9850, even if it's only functional when connected to WiFi?
I am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies View RelatedDoes it support SSL VPN? As I would like to have secure web access without installing other software.
View 1 Replies View RelatedHow to set up RVS4000 QOS settings to work with a VOIP phone system? I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection.
View 1 Replies View RelatedWe have used two Cisco RVS4000 to create the IPSec VPN between the main office and the branch office. The main office has SBS 2008. There is a Windows Server 2008 as the domain controller in the branch office. One branch office user has a laptop which is not in the domain, but his exchange account is set up in the Outlook. When he connects the laptop to the branch office network, he cannot connect to the exchange server and get the emails. Is there any configuration to set up in the router, server or Outlook?
View 1 Replies View RelatedI need properly configuring the RVS4000 device. I need all devices to be on the same subnet (192.168.0.x) and if I am drawing this out correctly in my head I would perform the following:Connect LAN port of RVS4000 to LAN port of the switch and statically assign a LAN IP of 192.168.0.251 to the RVS4000Switch is connected to LAN port of the 2Wire (192.168.0.254)Change operating mode from Gateway to Router in the RVS4000 Connections to the RVS4000 will obtain a DHCP IP address from the 2Wire that's upstream.As the WAN port of the RVS4000 would be unused, will it still answer requests for a VPN connection assuming the proper ports are forwarded to it?
View 1 Replies View RelatedI cannot connect to a PPTP on the outside of my network.We have a RV082, port 1723.It says verifying username and password but then disconnects.The error log says Blocked IP Spoofing.
View 1 Replies View RelatedIs it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies View RelatedI'm having trouble connecting my 360 to the wireless router to gain Internet access.I use my phone's Wi-Fi to gain internet access with NO issues. My current setup: NetGear Wireless router is connected to my D-Link wired router, and I can access the internet no problem. (10 MBPS down, 5MBPS up)When I try to connect the 360 to the Netgear Wireless router, it connects to the Network, but Internet test it reads "DNS error - The router or modem may mot be automatically providing DNS settings. Try a manual DNS setting instead."(Next suggestion) "DNS Error - If you have a PC that can successfully browse the web, check it's network properties to find the DNS address it uses..."Now, I have XBMC running on my computer, and the 360 can access the network so it shows up under Video Apps so I can see a file list to stream movies. When I try to run a movie, it says I must download an update - so I can't watch the movies at all.I juso set it up so I can access the Network AND Internet.Again, Netgear wireless router (which 360 connects to) connected to D-Link wired router.
View 10 Replies View RelatedI'm sure it's on here but because I dont understand the name of what I'm looking for, I'm having trouble searching. My main network is setup for wireless via a netgear wndr3700. I'd like to use my old linksys wrt54g v5 to connect to that network wirelessly and allow me to connect my xbox via wired ethernet. Basically instead of buying a wireless adapter for the xbox, i'd like to know if/ how i can use my linksys router instead.
View 13 Replies View RelatedI can connect to the router and connect to the Internet by by-passing the router, but can't connect through the router. firmware 2.51.4 is up to date, cables are all good. I can't find any diagnostic tools in the management screens - are there?
View 2 Replies View RelatedI recently tried to connect to my router via 192.168.1.1 (I've accessed it before) howvever this time it says the page is
unavailable. I've tried it several times for a couple days now and still it wont work. I have also tried 192.168.0.1
LAN L1, with IP addresses 192.168.10.x, for Company C1
LAN L2, with IP addresses 192.168.11.x, for Company C2
I have networks separated: different racks (but very closer fisically: a wire can be thrown), different gateways (to DSL), but both LAN's must connect with each other. I have acquired two RV042, one for each company to create VPN's (permitting telejob).
I have this E4200 for about 3 months and allways has been used as an wireless router. Today i wanted to connect 2 wired computers to it via lan and whatever i do dosnt connect. Dosnt even let me acces the 192.168.1.1 page to router settings.I am on firmware 1.0.02, i also did a full reset and then did set up with cisco connect, did try that thing with the cisco usb connect and still no joy with the LAN conection.
One comp uses win 7 the other is on win xp. I can connect both comps succesfully to other router via the gigabit ports but not to this one.
I have an E3200 router. I had been experiencing connection problems with my desktop that was wired to the router, and in an attempt to resolve the issue reset the router to its factory defaults. Now, as before the reset, I can connect to my router just fine via Wi-Fi (I have several devices connected this way) but none of the computers that I attempt to connect via ethernet are able to establish a connection. I have tested multiple cables with multiple computers using multiple ports on the router, to no avail. When I view the Status --> Ports page on the router, I can see the ports in use that I am connected to, but that is the only sign of connection that I get.
View 1 Replies View RelatedMy cable modem works fine when not running through the router. However, when running through the router, the internet won't work.I tried unplugging the power and plugging it back in, as well as holding down the reset button for 30 seconds, but nothing worked.
View 8 Replies View RelatedI have a WRT54GS router, and starting today I am completely unable to access the internet through it. If I connect my computer directly to my modem, I can access the internet, but if I try to connect through the modem, all I get is "DNS server not responding".I've tried changing the DNS server address on the router configuration page, but it doesn't work.
Here's what my ipconfig /all shows:
C:Windowssystem32>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : HomePCPrimary Dns Suffix . . . . . . . :Node Type . . . . . . . . . . . . : HybridIP Routing Enabled. . . . . . . . : NoWINS Proxy Enabled. . . . . . . . : No
[code]....
I have 2 PCs and am using a Linksys befsr41 router.The first PC connects fine. The 2nd PC does not find a connection. BTW, when I connect my laptop to the 2nd port, it sees the connection immediately - the lights flash on the ethernet connection. No lights on the 2nd desktop PC.
View 2 Replies View RelatedHow to connect two PCs and one DSL router to get on the internet?I am getting IP conflict error on the PC. I can only connect one PC at a time to get to internet.
View 1 Replies View Related1. Just got a new DLINK Xtreme N DIR-825 Router. Directly connected this to the internet.
2. Currently, the Linksys WRT54G (1st Generation) is connected to the DLINK by an Ethernet cable to one of the 4 ports on the back.
3. The Linksys further splits the signal to another 2 computers and a NAS by hardwire.
4. The internet is still getting through to all the computers, but the computers are not able to access the NAS or each other.
5. I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.
I can login to the NAS using its IP, and I can see it on the 'Network Places' of the computers ,but when I try to connect, it says the drive is moved, etc. etc.I use a variety of computers / O.S's on this system: XP (2) hardwired, Win 7 (2) hard wired, Win 7 (1) wireless, Mac OS X Snow Leopard (1) Wireless, plus various other wireless devices (phones,Wii, etc.).
NAS is a Synology DS411+
1) Get logged into my Linksys
2) Get the NAS accepted by other computers on the network.
I upgraded the firmware on my BEFS41 v4.3 to the Ver.2.00.4 Build 8, off the cisco website. After I received the successfully upgraded message, I could no longer connect to the internet, nor could I connect to the router's configuration page. I tried to do a few hard resets and connecting it to other computers to see any other computers could connect to it, no luck. I tried connecting one computer just to the router, without the internet plugged in, and tried to ping 192.168.1.1 but I received a "transmit failed, error code 1231." Is there anyway I can access this and change the firmware, or am I screwed?
View 3 Replies View Related
