Linksys Wired Router :: RVS4000 V02 IP Based ACL Not Working?
Mar 3, 2011
I have RVS4000 v02 and created 3 VLANs - 192.168.70.0/24, 192.168.80.0/24, and 192.168.90.0/24 . I tired to created IP based access list to deny network 192.168.80.0/24 and 192.168.90.0/24 to have access to 192.168.70.0/24; and deny 192.168.90.0/24 to access 192.168.80.0/24.
MY ACCESS LIST from RVS4000
Deny All Protocol LAN 192.168.80.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.70.0/255.255.255.0 Any Time Every Day
Deny All Protocol LAN 192.168.90.0/255.255.255.0 192.168.80.0/255.255.255.0 Any Time Every Day
Allow All Service LAN ANY ANY Any Time Every Day
Allow All Service WAN ANY ANY Any Time Every Day
* all access list is enabled.Both 192.168.80.0 and 192.168.90.0 network can still reach 192.168.70.0 network.
View 1 Replies
ADVERTISEMENT
Dec 20, 2008
I just installed an RVS4000 router for a SOHO. I have no problem getting out to the internet so access from LAN -> WAN is working fine. The problem is with VPN access from the WAN.I created a VPN account and set up QuickVPN on a PC making sure I imported the certificate. I can connect to the router with no problem and I can even connect to the routers web admin page.But that's where it ends. I cannot connect in any way, shape, or form to PCs on the LAN through the VPN. I can't even ping them.Am I missing something in the setup of the router?
This is the only reason I bought this router as the old one was working fine. How to fix getting through the router to connect to the computers on the LAN.
View 9 Replies
View Related
Feb 11, 2011
after using BEFSR41 for a long time without any problems, I decided to buy a new router RVS4000 to be able to have gigabit connections.
The problem is when I download a youtube video or I use VPN or even a desktop remote access, it always disconnect. I've seen many and many posts on this forum of people having this problem, I decided to try what you suggested to them:
- Changed the MTU to 1492
- Disabled IPS
- Disabled Firewall
- A couple of other things
- I already have the latest firmware
... and i've done some other tests in my side but nothing worked so far, just like for those who had this problem. I strongly think it's a problem on the router and not a problem from the user.
View 1 Replies
View Related
Jan 24, 2011
I have an RVS4000 located at my office. A user of mine also has one at their house. We have created an IPSec Tunnel between the 2 of them and have them successfully communicating between the 2 networks with no problem.
The problem I have is if I make a change on their end and the router needs to reboot to apply the changes, the WAN port never renews it's DHCP address. The end user must unplug the unit, plug it back in and then the system comes back up with the correct WAN DHCP address, and the tunnel is connected automatically.
I beleive they have the newest firmware (2.0.0.3) but I cannot confirm that right now as the unit is down. I bought the 2 of them at the same time - my unit at the office has the 2.0.0.3 firmware so I am assuming the users does as well.
View 1 Replies
View Related
Mar 14, 2011
I have successfully configured my Cisco RVS4000 for VPN Access, and Installed QuckVPN on my client machine. I can connect using QuickVPN no problem, but I cant access anything on my network. When I try pinging any of my servers I am unable to do so. I can ping my gateway thats about it.
View 1 Replies
View Related
Jun 23, 2011
I have a PPTP VPN server (WIndows 2008 R2) sitting behind an RVS4000, I have port forwarding for 1732 on and the client's (Windows 7) can reach the VPN server but cannot complete the connection due to an 806 error, which is GRE traffic related. I have PPTP passthrough on and have also created a ACL entry for PPTP traffic. I've seen many posts on this topic over several years with no solutions, and I do have the latest firmware (Version:V1.3.3.5). This is also definetely router related as I have absolutley no problem connecting when I point directly to the VPN server by internal IP address.
View 1 Replies
View Related
Jan 24, 2013
We share a common fibre connection to the internet. In the basement we have a modem/router(zyxel) which is in "bridge mode". Therefore not acting as DHCP.Behind this zyxel we have a Cisco RVS4000 router. Ports 1 and 2 go to family A, and Ports 3 and 4 go to family B.Family A and B have separate routers which are both set to "access point mode". Family A has an ASUS RT-N66U router while family B has a dlink DIR-615. The asus has an "access point mode" while the dlink needs to be set up manually to achieve this. The dlink must also have a static IP adress. The asus can receive ip adress.
View 1 Replies
View Related
Mar 10, 2013
I am trying to configure my RVS4000 to create my church's small network. I want to connect my internet DSL router on the WAN port and also segment my network with VLANs on the 4 LAN ports. I have port 4 connected to a wireless access point which is in VLAN1 for an open wireless network for any church member to access the internet through. I have a church server, printer and second access point on ports 1-3 in VLAN 34. All ports are untagged. I want the devices on VLAN34 which need confidentiality to be secure from the devices connecting to the internet from VLAN1 for open access but both VLANs need access to the internet..
My open wireless AP in VLAN1 has access to the internet on the WAN port.None of my devices in VLAN34 have access to the internet. I have tried using inter-VLAN routing but that made operation worse so I disabled it.
View 1 Replies
View Related
Apr 21, 2011
I've looked through the documentation that came with the router and there is no instructions on how to configure the 4000 to accept remote clients and access the local network. What the configurations are so a client can launch the vpn client, login, and remote desktop to their local workstations in the office? I don't have any tunnels or connections setup with other offices, just a simple client connection.Also, will the rvs4000 work with Cisco VPN client (comes with higher end appliances)?
View 1 Replies
View Related
Apr 27, 2008
How to setup quickvpn to work with RVS4000.
View 9 Replies
View Related
Mar 14, 2008
Just purchased a RVS4000. How to be successfully able to VPN into this device from os/x? If so what software / settings required.
View 6 Replies
View Related
May 31, 2012
I am trying to connect a LAN to the internet via an RVS4000 for remote access to the LAN and cannot connect to the RVS4000. I am using a static WAN address, entered it in the WAN setup area (subnet, gateway, etc.). I do not use DHCP as all the LAN units are static addressed. I rebooted, etc. but cannot see the router externally (I am pinging from a remote site).If I plug my laptop into the WAN cable and set the laptop to the WAN adress, I have no issues. I have checked the cables (all CAT5e shielded), checked both straight through and crossover cables, and have no luck.
View 1 Replies
View Related
Feb 2, 2012
I connect to my RVS4000 VPN router using QuickVPN. Very useful.
Sometimes I am not near my laptop and need to check data.
Is there a QuickVPN or compatible client for a BlackBerry Torch 9850, even if it's only functional when connected to WiFi?
View 1 Replies
View Related
Apr 30, 2013
I am being told from my remote end I do not have port 22 opened up. I have single port forwarding to SSH 22 and Port Range 22 enabled.
View 1 Replies
View Related
Mar 15, 2011
Does it support SSL VPN? As I would like to have secure web access without installing other software.
View 1 Replies
View Related
Dec 15, 2011
How to set up RVS4000 QOS settings to work with a VOIP phone system? I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection.
View 1 Replies
View Related
Aug 2, 2011
We have used two Cisco RVS4000 to create the IPSec VPN between the main office and the branch office. The main office has SBS 2008. There is a Windows Server 2008 as the domain controller in the branch office. One branch office user has a laptop which is not in the domain, but his exchange account is set up in the Outlook. When he connects the laptop to the branch office network, he cannot connect to the exchange server and get the emails. Is there any configuration to set up in the router, server or Outlook?
View 1 Replies
View Related
Mar 16, 2011
I need properly configuring the RVS4000 device. I need all devices to be on the same subnet (192.168.0.x) and if I am drawing this out correctly in my head I would perform the following:Connect LAN port of RVS4000 to LAN port of the switch and statically assign a LAN IP of 192.168.0.251 to the RVS4000Switch is connected to LAN port of the 2Wire (192.168.0.254)Change operating mode from Gateway to Router in the RVS4000 Connections to the RVS4000 will obtain a DHCP IP address from the 2Wire that's upstream.As the WAN port of the RVS4000 would be unused, will it still answer requests for a VPN connection assuming the proper ports are forwarded to it?
View 1 Replies
View Related
Feb 28, 2011
Is it possible to assign public IP address as Router's local IP address (RVL200, RVS4000)?
View 1 Replies
View Related
Aug 8, 2009
I'm having an issue with a Linksys RVS4000 which doesn't appear to be behaving as I think it should.I need to forward a port (Single Port Forwarding) through to an internal NAT host. However, I only want that host/port to be accessible from one host on the internet, for security reasons.
I have created the port forwarding entry and this works fine. I then created two rules in IP Based ACL - one to block all access to that port from the WAN interface and one to allow access from a single host.
However, it appears that when a port forwarding entry is added, it will completely bypass the ACL and allow all traffic for that port/host by default.Is this the correct behaviour?
Firmware version is v1.2.11
View 12 Replies
View Related
Jan 11, 2011
we have two desktop Pc's both hard wired to a Linksys router. One P.C is on Windows 7 system the other is on Vista. The windows 7 is connecting O.K. The one on Vista is showing " Does not have a wireless network adaptor, install & configure. The Vista P.C. was working O.K. a couple of days ago.Also not connecting to a laptop from the host computer on the Vista system?
View 2 Replies
View Related
Feb 3, 2011
I have a Century Link DSL connection in my house and its working fine. I just got a new Linksys BEFSR41 v.3. I am trying to set it up for my PC, Xbox360 and BD player. Everything works fine when I plug them in to the DSL modem 1 by 1 but when I try to put the Linksys "in the middle"... nothing... So I'm pretty sure its not my DSL modem or connection.All the lights come up on the Linksys as they should (power, internet and the Ethernet) but for some reason it seems the internet not getting trought the router. When its connected and I pull up my internet browser I type 192.168.1.1 and it takes me to the linksys config site. Without the router in the same address go to the Westell site as thats my DSL modem. Everything looks fine on the config site. All the correct IP, MAC, DNS address are there and still no internet access on any of my device.
View 1 Replies
View Related
Dec 12, 2006
I just buy the BEFSR81,still not working.
View 3 Replies
View Related
Mar 14, 2012
I have the same problems with the Cisco EPC3925?Everytime a wired pc reboots/boots everyone on the network losses internet, also wireless is disconnected. Also everyone get unidentified network and later its set to public network.We are using a Sitecom switch LN-120. I have to unplug this switch, then restart the router to fix the problem each time. Then I can plug it in again and everything is fine.The router will not restart (does not go further then 2nd blinking LED.) if I do not unplug the switch.
View 8 Replies
View Related
Jul 9, 2011
I have a Linksys RPT300 (firmware 3.1.27) which I need to pass magic packets on port 9 to internal computer. on LAN the WOL works perfectly.I have masked my local lan to 255.255.255.128 to be able to broadcast on another subnet address than x.x.x.255 which the web interface dont seem to allow.Local LAN is 192.168.15.x and I have created a port forward on port 9 UDP to local broadcast address wich would then be 192.168.15.127. However nothing comes through and I cant seem to find a setting to enable/disable internet broadcasts. Is there a work around?
View 1 Replies
View Related
Nov 4, 2007
I have a linksys BEFSR41 V.2 router with four ports. Ports #1 and #3 are working but the other two do not. The diag. light just blinks rapidly.
View 4 Replies
View Related
Jan 28, 2011
Working System: Arris -> BEFSR41 (dhcp) -> to four computers working fine.
As soon as I add the EZXS16W, computers plugged into EZX no getting internet. I have the back button depressed so it will work as a 16 port hub.
Not Working System:
Arris -> BEFSR41 Port 1 ----------------------------------------->EZXS16W ----> Computer (not working)
BEFSR41 Port 2 ->Computer (working) EZXS16W ----> Computer(not working)
BEFSR41 Port 3 -> Computer (working) EZXS16W ----> Computer(not working)
BEFSR41 Port 4 -> Computer (working) EZXS16W ----> Computer (not working)
View 5 Replies
View Related
Dec 8, 2011
I have an E4200 router & am trying to get it to work with ATV2 through HomeSharing & iTunes. It works fine when my PC is wireless & the ATV2 is wireless. BUT, when the ATV2 is wired via ethernet & the PC is wireless -- nothing!
PC is Win 7 64 - SP1
ATV2 is 4.4.3 (3323) and the router is:
E4200 is 1.0.03 build 14
View 4 Replies
View Related
Jun 24, 2012
I have the WRT54G router for years and use it to provide both a wireless network for our home computers and a wired network for by internet phone that connects me to my office phone system and for my work computer and printer. Last week, the wired network stopped working. I checked the wiring and plugged my wire into all four of the ports in the back of the router with no success. I followed the troubleshooting procedure that I found and changed the MTU setting. I tried to update the firmware but the screen seemed to lock up and I was unable to complete the task.
View 9 Replies
View Related
Feb 28, 2013
The router stopped working for wired connections. I can still go online using my laptop via wifi, but when I connect a network cable to the laptop and turn off wi fi, connection does not work. Can't go online with a desktop with a wired connection to router.Everything else works via wi fi: iPad, android phone, tv with wifi.
View 1 Replies
View Related
Jul 31, 2012
My router was working just fine forever, the only computer that will connect VIA wire is my desktop, everything else for it to connect to my network it has to go wireless. Things like my blu ray player just will not connect. I am not an expert at all, but why is only the wireless working? I can use the Cisco connect and adjust the settings if need be.
View 5 Replies
View Related
Jun 9, 2012
just purchase this RV016 and the firmware has been updated to 3.0.2.01-tm.Every download I try through the router leads to a curruption somehow, even though the download manager gets it all. If I go straight from the cable modem I have no problems.It's a 4mbps upload and 0.8 downlink from what speedtest shows. I have tried diff DL managers, and get the same result on different connected PC's. The great thing about the RV016 is it speeds up the connection on this cable modem.What can I change to get downloads working?
View 1 Replies
View Related
Apr 8, 2012
I am a novice with networks but do have a fair understanding of networks. I have a small business network, utilizing a RVS4000 router (Firmware V2.0.27)I am attempting to set up firewall rules to block certain web sites at certain times.I have successfully set up rules using source and destination ranges, to deny service 24 hours a day everyday.
However and here is the problem when I attempt to edit any of the rules (I want to change the time to certain hours of the day) it allows me to edit the rule but when I attempt to save I get an error message up saying there are invalid characters and it will not save the changes?create the whole thing with the changes I want it works fine, is this a known bug?
View 1 Replies
View Related
