I have an E4200 router & am trying to get it to work with ATV2 through HomeSharing & iTunes. It works fine when my PC is wireless & the ATV2 is wireless. BUT, when the ATV2 is wired via ethernet & the PC is wireless -- nothing!
PC is Win 7 64 - SP1
ATV2 is 4.4.3 (3323) and the router is:
E4200 is 1.0.03 build 14
My router was working just fine forever, the only computer that will connect VIA wire is my desktop, everything else for it to connect to my network it has to go wireless. Things like my blu ray player just will not connect. I am not an expert at all, but why is only the wireless working? I can use the Cisco connect and adjust the settings if need be.
View 5 Replies View RelatedMy E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.
View 2 Replies View RelatedI have this E4200 for about 3 months and allways has been used as an wireless router. Today i wanted to connect 2 wired computers to it via lan and whatever i do dosnt connect. Dosnt even let me acces the 192.168.1.1 page to router settings.I am on firmware 1.0.02, i also did a full reset and then did set up with cisco connect, did try that thing with the cisco usb connect and still no joy with the LAN conection.
One comp uses win 7 the other is on win xp. I can connect both comps succesfully to other router via the gigabit ports but not to this one.
I see on the control panel that there is MAC filtering for the wireless connections. I don't see a similar control panel for computers that are wired directly to the router. Where do I find this?
View 3 Replies View Relatedmy general internet connectivity with my e4200.I have a new but similar problem today with the same router.After powering down equipment and moving it around, my wired connections all error. Error in that they will not get an IP address nor will they connect to the internet or each other.My wireless connections still work flawlessly.
I tried powering down the devices over night (to avoid any heating issues) and then powering up but the results are the same. I am obviously missing something, and don't really want to start my network from scratch again...
Installed E4200 with an iMac running MacOS X Version 10.6.8. Wireless connection works great. Also connected a wireless laptop without a problem. But can't connect a 2nd computer is wired. That is a PC running Vista. I know the wiring is good, because the E4200 is a replacement router in a network that was working fine.
View 1 Replies View RelatedI'm trying to fix the network at a student housing building and the system is kind of a mess. We bought a new E4200 to replace our old Linksys router which no one knows the admin pw to. We have four switches for 50 connections throughout the four story house and when switching the connections over to the new E4200 all of the wired connections no longer work. Switch back to the old router and presto. How do I need to change the settings with the E4200 to get it to work?
Also, as it's a thick old house the E4200's wireless only covers maybe half of it...I purchased two wireless repeaters to put on the 3rd and 4th floors, are these simple to install with the router?
I lost all Internet connnecitivity on my Linksys e3000. After determining that my cable modem was connected and working correctly, I pulled the e3000 and put my old wrv54g router in place. Wireless worked, but all wired connections showed link but no other apparent connectivity. Neither of my desktops could get a DHCP lease.
At that point, I purchased and manually installed a new e4200 router. All worked fine. Both laptops connected via wireless and both desktops via my house LAN. Until this morning (Monday). Wireless is working just fine, but both wired computers show 100 Mbs connections on an unknown network with no DHCP. Checking status shows packets going out, but nothing coming in. Checking LAN status on the router shows that both ports are connected, but it does not appear to receive anything from either desktop. All was fine last night. Oh, the router is on 1.0.03 firmware.
I have tried about everything I can think of. Configurations both on the router and the desktops (one Windows XP, 64 bit and one Windows 7) and all seems fine. I have disabled and reenabled the network connectors, rebooted both the router and the computers, etc. Nothing seems to work.
Can we disable wireless totally in E4200 and just use wired connections? I didn't see any configuration for that, but just in case I missed it. I'm also aware we can disable SSID Broadcast.
View 1 Replies View RelatedI just bought a new Linksys E4200, and connected it about an hour ago. I have a 30Mbps internet connection when connected direct to the modem, but when connected wired to the router, max speeds are 8Mbps.
View 2 Replies View RelatedI just upgrade my E4200 V2 from 2.0.37 to 2.1.38 (finally! would be nice if I knew before that I had to unzip the file before I could flash it....)
But when I enable NAT in the settings, there is no way to edit NAT entries that I've set before under firmware 2.0.37.
I saw one post recommending to changing the MTU from 1500 to 1400. That did absolutely nothing. My comcast internet is now slower than 14.4 dial up modem I had 16 years ago. The strange thing is I can sometimes download at over 2 mbps with torrents. It's mainly loading websites where the speed is so bad.
View 9 Replies View RelatedAs soon as i modify my wireless to be unsecured, I looy ability to usse me the internet on all wired ports as well as all wireless. From the routers point of view it still has a good solid internet connection. Passes traceroute, but wont allow any wired or wireless connections on the internet. I'm trying to get a Linksys WRE54G v1 to work with this so my parents can have internet once more. If i manualy remove the security to allow the one touch Auto configuration button to work i loose my ability to surf until i run the Cisco Connection software to turn back on the passwords.
View 7 Replies View RelatedJust upgrade my Thinkpad to win7 64bit, but seems the wireless doesn't support by E4200 now, upgraded 1.0.03 and latest intel 14.2.0.10 for wlan card but still not working. Tried the TP with USB WN111v2 is not problem at all.4965AG works perfect in office WPA2 AES LEAP and netgear router.
View 9 Replies View RelatedI own a E4200 v1 router and recently discovered that wired and wireless devices cannot talk to each other.Their IP address are acquired through DHCP and inside the same network, but cannot talk to each other by any means, such as ping or http connection.I tried switching wired device to wireless and this actually solve the problem. I've searched and seen thread talking about "AP isolation" settings in advanced wireless setting, but there's no such setting page in my router (running on v1.0.5 firmware). I've already disabled any filtering and firewall function on the router, but still no good.
View 1 Replies View RelatedI cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies View RelatedI just upgraded to an E4200 from a D-Link DIR-655. I cannot seem to get my desktop to connect to the E4200 at 1 GBS. My adapter is set to "auto negotiate" but will only connect at 100 MBS. If I try forcing the adapter setting to 1 GBS, it never connects. I can swap out my E4200 with the DIR-655 and it will connect at 1 GBS just fine. I am using a CAT 5E cable. Is there something I'm missing here or is the E4200 just more finicky than the the DIR-655?
View 9 Replies View RelatedI just bought the E4200 routher at best buy a few weeks ago. I got it all setup how I want it. Its been working fine then about a day ago it started to stop working at random. All internet just stops working. Wired and Wifi. I have to either wait for it to work again or restart the router.
View 7 Replies View RelatedI have been using the E4200 router with few issues for the past 5 months. I have the latest firmware installed and have 1 pc running Windows 7, a sling box device and USB storage drive connected in the rear and 7 wireless devices.
Over the past week, others in my household have been complaining of not being able to connect wireless. The other day, the connection quit for both wireless and wired connections. I thought it had something to do with my ISP (Comcast), and after I made a direct connect from my modem to my PC, the problem is the E4200. After unsuccessfully troubleshooting, I unplugged the router for a few hours.
Trying a few hours later, I was able to reconnect all connections. However, that lasted for a day and has not been able to connect. I did a reset and when going through the setup process, it says that it cannot connect to the internet. The only time I have any lights or activity on the internet port is when the router is booting up and then it goes off. The rest of the ports are working properly. Likewise, the link light on my modem shows no activity when connected to the E4200. The only connection I can make is to the browser utility.
I am now using another wireless router until I can get this resolved.
The latest Firmware for the E4200 states that there is now the ability to attach a printer to the USB port of the router. I am using a Mac, so that may be the problem, but I have followed the instructions on how to add the printer and it is not happening. It's possible that the MAC Firmware was not given the ability to add a USB printer like the PC Firmware upgrade.
View 9 Replies View RelatedI am having a trouble with my router, our modem is the one that is connected to a TV box and it comes with a wifi function(a modem with a wifi function). I am not sure how to set it up, so I connected it to E4200 which is located in another room using CAT6 flat cable and set it to "Bridge mode". But whenever I open the TV box, the wifi won't work, and when it's closed, it works. :s how weird is that. Are there any problems? The modem with wifi will always work either way I open/close the TV box, but the E4200 wifi will only work when I close the TV box. I asked my service provider about this and they tell me it's not their problem anymore.
View 2 Replies View RelatedJust recently bought a Linksys E4200 router and it's been rocking so far! I upgraded from a WRT320N. However it seems that calling with SIP (using my Voip Buster account) doesn't work anymore.I don't seem to be able to register with the Voip service. Port is the standard 5060 (if my memory serves me well, I'm not at home now) and I already activated on the router the special tick for Voip ALG calling. Router is upgraded to the latest firmware and it's the V1 router.With all of the above, I still can't connect using SIP to VoiceBuster. It worked like a charm with the WRT320N so it's something with the router?.
View 2 Replies View RelatedI installed an E4200 in an outdoor patio area where the ambient temperature can be high (Las Vegas area); however, the router is located in the shade without any direct exposure to the sun. After using the router for about 15 minutes, the router is extremely hot and 2.4GHz band will stop working. In addition, even when the router is working, the 5 GHz band connects at much higher speed than the 2.4 Ghz band. The internet download speed is much higher using 5 GHz compared to 2.4 Ghz.
View 9 Replies View RelatedI recently upgraded my linksys E1000 to: linksys E4200 ( i needed gb port)
In my QNAP I can scan for upnp routers to set the forwarding port automaticly.
But it keeps telling my, it can't find an upnp router on my network. My E1000 was found without any problem!
If I open the port manually for example FTP 21. I cannot get acces from the internet, it keeps telling me its closed.
I forwarded it to the right ip. an clicked to apply. The website from QNAP says the E4200 is certified for upnp
So tho sum up: I cannot acces my NAS from the internet.
My setup:
Modem/router (ZIGGO) --- Linksys E4200 ---- QNAP 412 turbo
Linksys E4200 firmware 10.04
I've lost connectivity with all but one of the ethernet ports on my E4200 router. My desktop PC was connected to Port 1 but stopped working. Network troubleshooting via my Windows 7 Dell 8300 said I was not connected and to check the cable. I did that with several different cables and tried the usual router and modem reset. Only through trial and error did I find that I could connect to port 4 which is why I am able to write this post. What could have changed to disable ports 1-3 and can I get them working again? No issues with wireless connectivity.
View 3 Replies View RelatedI'm having a bit of trouble with my e4200, It keeps on "dropping" connection, and by dropping I mean it constantly around 3-5 minutes the internet stops working with all my computers, it's connected by wifi with 2 PC's, and 1 PC is wired with an ethernet cable, and I also have 2 mobile devices connected at it. The internet would start working again within 30s, to 1m, but that it drops soon.Methods I've done to fix it:
-Updated firmware to the latest one
-Set the MTU to 1400
-Reset it, (30 second press)
-Rebooted, (Cooled down, doesn't really run hot just a little warm)
-Restored to factore defaults
I purchased an e4200 about 6 months ago and it worked great until the other night the Internet stopped working on my laptop (wireless). I tried unplugging both my modem (Motorola Surfboard) and router and plugging them back in, but no luck. I can accesss the Internet when plugged directly into the router (with both my PC and laptop), so it looks like the issue is with the e4200. To make matters worse (and I fear much worse), I can't even access the admin page to the router through either the Cisco Connect software or through the IP address. I've tried resetting it, I've tried the 30/30/30 reset (holding the reset button while doing an unplug and pluging back in), and reinstalling the Cisco Connect software, all to no avail.
I've found threads where others have not been able to access the admin page, but they still had access to the Internet url... I haven't found a similar thread where the router doesn't seem to work at all. A few other bits of information I can think of (let me know if there's other information I can provide):The Cisco logo light flashes slowly after reset which I believe is expected.The lights in back of the router seem to work as intended.Running Windows 7 Diagnostics finds the connection "doesn't have a valid IP configuration" and "The default gateway is not available."
I have the WRT54G router for years and use it to provide both a wireless network for our home computers and a wired network for by internet phone that connects me to my office phone system and for my work computer and printer. Last week, the wired network stopped working. I checked the wiring and plugged my wire into all four of the ports in the back of the router with no success. I followed the troubleshooting procedure that I found and changed the MTU setting. I tried to update the firmware but the screen seemed to lock up and I was unable to complete the task.
View 9 Replies View RelatedThe router stopped working for wired connections. I can still go online using my laptop via wifi, but when I connect a network cable to the laptop and turn off wi fi, connection does not work. Can't go online with a desktop with a wired connection to router.Everything else works via wi fi: iPad, android phone, tv with wifi.
View 1 Replies View RelatedI have a E4200 updated to the latest firmware I have problems with the wifi on the 2.4GHz band, in fact, at power on, many times wi-fi on the 2.4GHz band doesn't work but the 5GHz band works normally. After some reboots the wi-fi operating normally on both bands.
View 9 Replies View RelatedI'm currently using onboard lan card of P6X58D Premium. However in the Cisco web setup page or even in my Windows 7, it shows only 100Mbps connection. I tried to force to 1000Mbps but it failed to get an IP. I did a google and found that may be the router doesn't do well with Intel card, but I use another onboard lan card with Nivida chip+AMD CPU, it's still only have 100Mbps. What can I do to have a 1000Mbps connection?
View 5 Replies View RelatedSo I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View Related