Linksys Wireless Router :: E4200 / WRT320N Calling With SIP Not Working
Feb 13, 2012
Just recently bought a Linksys E4200 router and it's been rocking so far! I upgraded from a WRT320N. However it seems that calling with SIP (using my Voip Buster account) doesn't work anymore.I don't seem to be able to register with the Voip service. Port is the standard 5060 (if my memory serves me well, I'm not at home now) and I already activated on the router the special tick for Voip ALG calling. Router is upgraded to the latest firmware and it's the V1 router.With all of the above, I still can't connect using SIP to VoiceBuster. It worked like a charm with the WRT320N so it's something with the router?.
View 2 Replies
ADVERTISEMENT
Jul 20, 2011
I have a Linksys WRT320N wireless router at my salon with an Ethernet connection to my POS terminal, and wireless access for my notebook. When it was originally set up (by a technical person), I used a password that is my own personal (private) password. Since then, when my clients have asked to use the wireless network, I have had to enter my password into their device since I can't tell them what it is.
Today I decided to resolve the issue, so I changed the password to something simple. But, now the password only seems to work for me and not anyone else.
I don't understand why this is happening, when my previous password worked fine on other devices.
I hesitate to keep messing with it since I am not a very technical person. For example, just changing the password today and resetting the router, etc, was a challenge and I about had a heart attack when my POS terminal wasn't responding (luckily I got some assistance from my Internet provider, even though its not their router).
I do not have Cisco Connect installed on my Notebook at work (did not have a CD drive at the time). I do have a CD drive now and can install Cisco Connect if necessary. (Again, a bit of concern that I will screw something up in the process and not have POS access.)
View 3 Replies
View Related
Aug 6, 2012
I just upgrade my E4200 V2 from 2.0.37 to 2.1.38 (finally! would be nice if I knew before that I had to unzip the file before I could flash it....)
But when I enable NAT in the settings, there is no way to edit NAT entries that I've set before under firmware 2.0.37.
View 1 Replies
View Related
Nov 14, 2011
Just upgrade my Thinkpad to win7 64bit, but seems the wireless doesn't support by E4200 now, upgraded 1.0.03 and latest intel 14.2.0.10 for wlan card but still not working. Tried the TP with USB WN111v2 is not problem at all.4965AG works perfect in office WPA2 AES LEAP and netgear router.
View 9 Replies
View Related
Jun 24, 2011
I cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies
View Related
Feb 17, 2011
I just upgraded to an E4200 from a D-Link DIR-655. I cannot seem to get my desktop to connect to the E4200 at 1 GBS. My adapter is set to "auto negotiate" but will only connect at 100 MBS. If I try forcing the adapter setting to 1 GBS, it never connects. I can swap out my E4200 with the DIR-655 and it will connect at 1 GBS just fine. I am using a CAT 5E cable. Is there something I'm missing here or is the E4200 just more finicky than the the DIR-655?
View 9 Replies
View Related
Oct 5, 2011
I just bought the E4200 routher at best buy a few weeks ago. I got it all setup how I want it. Its been working fine then about a day ago it started to stop working at random. All internet just stops working. Wired and Wifi. I have to either wait for it to work again or restart the router.
View 7 Replies
View Related
Jul 24, 2011
I have been using the E4200 router with few issues for the past 5 months. I have the latest firmware installed and have 1 pc running Windows 7, a sling box device and USB storage drive connected in the rear and 7 wireless devices.
Over the past week, others in my household have been complaining of not being able to connect wireless. The other day, the connection quit for both wireless and wired connections. I thought it had something to do with my ISP (Comcast), and after I made a direct connect from my modem to my PC, the problem is the E4200. After unsuccessfully troubleshooting, I unplugged the router for a few hours.
Trying a few hours later, I was able to reconnect all connections. However, that lasted for a day and has not been able to connect. I did a reset and when going through the setup process, it says that it cannot connect to the internet. The only time I have any lights or activity on the internet port is when the router is booting up and then it goes off. The rest of the ports are working properly. Likewise, the link light on my modem shows no activity when connected to the E4200. The only connection I can make is to the browser utility.
I am now using another wireless router until I can get this resolved.
View 3 Replies
View Related
Jun 21, 2011
The latest Firmware for the E4200 states that there is now the ability to attach a printer to the USB port of the router. I am using a Mac, so that may be the problem, but I have followed the instructions on how to add the printer and it is not happening. It's possible that the MAC Firmware was not given the ability to add a USB printer like the PC Firmware upgrade.
View 9 Replies
View Related
Dec 8, 2011
I have an E4200 router & am trying to get it to work with ATV2 through HomeSharing & iTunes. It works fine when my PC is wireless & the ATV2 is wireless. BUT, when the ATV2 is wired via ethernet & the PC is wireless -- nothing!
PC is Win 7 64 - SP1
ATV2 is 4.4.3 (3323) and the router is:
E4200 is 1.0.03 build 14
View 4 Replies
View Related
Jun 5, 2012
I am having a trouble with my router, our modem is the one that is connected to a TV box and it comes with a wifi function(a modem with a wifi function). I am not sure how to set it up, so I connected it to E4200 which is located in another room using CAT6 flat cable and set it to "Bridge mode". But whenever I open the TV box, the wifi won't work, and when it's closed, it works. :s how weird is that. Are there any problems? The modem with wifi will always work either way I open/close the TV box, but the E4200 wifi will only work when I close the TV box. I asked my service provider about this and they tell me it's not their problem anymore.
View 2 Replies
View Related
Jun 19, 2011
I installed an E4200 in an outdoor patio area where the ambient temperature can be high (Las Vegas area); however, the router is located in the shade without any direct exposure to the sun. After using the router for about 15 minutes, the router is extremely hot and 2.4GHz band will stop working. In addition, even when the router is working, the 5 GHz band connects at much higher speed than the 2.4 Ghz band. The internet download speed is much higher using 5 GHz compared to 2.4 Ghz.
View 9 Replies
View Related
Mar 9, 2012
I recently upgraded my linksys E1000 to: linksys E4200 ( i needed gb port)
In my QNAP I can scan for upnp routers to set the forwarding port automaticly.
But it keeps telling my, it can't find an upnp router on my network. My E1000 was found without any problem!
If I open the port manually for example FTP 21. I cannot get acces from the internet, it keeps telling me its closed.
I forwarded it to the right ip. an clicked to apply. The website from QNAP says the E4200 is certified for upnp
So tho sum up: I cannot acces my NAS from the internet.
My setup:
Modem/router (ZIGGO) --- Linksys E4200 ---- QNAP 412 turbo
Linksys E4200 firmware 10.04
View 9 Replies
View Related
Oct 27, 2011
I've lost connectivity with all but one of the ethernet ports on my E4200 router. My desktop PC was connected to Port 1 but stopped working. Network troubleshooting via my Windows 7 Dell 8300 said I was not connected and to check the cable. I did that with several different cables and tried the usual router and modem reset. Only through trial and error did I find that I could connect to port 4 which is why I am able to write this post. What could have changed to disable ports 1-3 and can I get them working again? No issues with wireless connectivity.
View 3 Replies
View Related
Feb 3, 2013
I'm having a bit of trouble with my e4200, It keeps on "dropping" connection, and by dropping I mean it constantly around 3-5 minutes the internet stops working with all my computers, it's connected by wifi with 2 PC's, and 1 PC is wired with an ethernet cable, and I also have 2 mobile devices connected at it. The internet would start working again within 30s, to 1m, but that it drops soon.Methods I've done to fix it:
-Updated firmware to the latest one
-Set the MTU to 1400
-Reset it, (30 second press)
-Rebooted, (Cooled down, doesn't really run hot just a little warm)
-Restored to factore defaults
View 4 Replies
View Related
Jul 11, 2012
I purchased an e4200 about 6 months ago and it worked great until the other night the Internet stopped working on my laptop (wireless). I tried unplugging both my modem (Motorola Surfboard) and router and plugging them back in, but no luck. I can accesss the Internet when plugged directly into the router (with both my PC and laptop), so it looks like the issue is with the e4200. To make matters worse (and I fear much worse), I can't even access the admin page to the router through either the Cisco Connect software or through the IP address. I've tried resetting it, I've tried the 30/30/30 reset (holding the reset button while doing an unplug and pluging back in), and reinstalling the Cisco Connect software, all to no avail.
I've found threads where others have not been able to access the admin page, but they still had access to the Internet url... I haven't found a similar thread where the router doesn't seem to work at all. A few other bits of information I can think of (let me know if there's other information I can provide):The Cisco logo light flashes slowly after reset which I believe is expected.The lights in back of the router seem to work as intended.Running Windows 7 Diagnostics finds the connection "doesn't have a valid IP configuration" and "The default gateway is not available."
View 9 Replies
View Related
Jul 31, 2012
My router was working just fine forever, the only computer that will connect VIA wire is my desktop, everything else for it to connect to my network it has to go wireless. Things like my blu ray player just will not connect. I am not an expert at all, but why is only the wireless working? I can use the Cisco connect and adjust the settings if need be.
View 5 Replies
View Related
Aug 21, 2011
I have a E4200 updated to the latest firmware I have problems with the wifi on the 2.4GHz band, in fact, at power on, many times wi-fi on the 2.4GHz band doesn't work but the 5GHz band works normally. After some reboots the wi-fi operating normally on both bands.
View 9 Replies
View Related
Feb 22, 2012
I am trying to set up WRT on my WRT320N access point so I can connect it to my other access point that also doubles as my DSL router.Where can I find the WDS on the WRT320N?
View 1 Replies
View Related
Apr 25, 2013
I have a WRT320N, firmware version 1.0.05., Windows 7 Home Premium SP1, and a Hewlett Packard laptop.I would like to utilize both bands on my router at the same time for internet access, so that I can have the one my kids use shut down at a certain time but mine stay up.If not, what's the closest I can get, even if I have to purchase additional items to do so? Do I have to manually turn their band off when I want it off? And can I even have both bands in use at the same time?
I looked at my Cisco online info by access the IP address. I see the Access Restrictions tab. Can I even set usage by specific computer? If so how do I do that?
View 3 Replies
View Related
Jul 20, 2009
After playing around I cannot get the router to get into the wide 40 MHz mode any more (2.4 GHz)
View 5 Replies
View Related
Dec 6, 2011
I've purchased this router a few weeks ago, but I can't use it as I can't get on the internet with it plus my laptop which as wifi will not recognize it.
I would really like get it going, I've tried live chat but I guess the techy didn't have the patience, I am a slow typer for lack of a better word.
View 1 Replies
View Related
Jul 27, 2012
Just installed linksys wrt320n. Desktop and one laptop (wireless) connect. Both windows 7. A second laptop (Vista) errors out with message "the selected data rate is not correct". This laptop sees the router (since I see the router name and it validates the passphrase) but I cannot ping the router. I saw two messages on this site suggesting to enable WMM and use security WPA2. I have verified that both of these are so set.
View 9 Replies
View Related
Feb 2, 2011
I'm currently using my WRT320N router as an access point (connected to another linksys router), but I've lost my username and password to access the web-based utility. So I need to press the reset button and set it up again. Currently everything is working fine, but I've forgotten how to configure the router for this purpose, and I can't find instructions in the user's guide online. I seem to remember it being troublesome. I know I have to assign a different IP address (currently I'm using 192.168.1.113.) What other settings (if any) need to be changed?
View 2 Replies
View Related
Aug 16, 2011
I want to setup the following:
Internet through DSL-Thompson TG 789 VN router ---> several yards --> Linksys WRT320N --> wired computer netwerk | |with printer
| |
---> Wireless Netwerk --> laptops / phones <--- (WAN depending on strongest signal)
|
---> several servers
The Thompson does the DHCP and routing. It is the gateway through the internet, IP 192.168.2.254 (mask 255.255.255.0).I can't replace the thompson since it is delivered by my provider. SSID = BertB I want to achieve that all the compuers / laptops / phone and printer are in one network and can communicate with each other So the only possibility, as far as I can see, is to set up the Linksys as a bridge.
I have to do the following at the Linksys but have some questions as mentioned below:
SSID = BertB (the same)
channel = different from the channel used by Thompson
DHCP = off
IP = fixed (192.168.2.253)
gateway = 192.168.2.254
[code]....
how the thompson and the Linksys will build a connection with each other, or will this happen automatically through the above setup?Do I have to put the mac address of the thompson in the Linksys and/or vice versa?
View 1 Replies
View Related
Oct 8, 2009
How do I disable the wireless?
View 9 Replies
View Related
Dec 14, 2009
I just bought a Linksys 320N router to replace another competitors router. I am trying to connect to my VPN server from outside my network. I have the external ip to my network. I setup the new 320N router just like the old router. set dmz ip to internal ip of vpn server, set port forwarding to 1723, both, internal ip of vpn server, I have a way to test the vpn while i am inside my network. So, I can watch the VPN server log and see the request come into the server and it times out with the Linksys 320 N hooked up. If I have the old router hooked up, the vpn establishes a connection.
View 9 Replies
View Related
Jul 24, 2011
I have a WRT320N router with firmware version 1.0.01 build 008. I just got an iPad and while it can find my router, I can't access the WiFi when I enter my password. I can use the router with my laptop so I know the connection and password are ok.I've seen two administrators on here suggest the same thing. And one person responded that it worked. The identical directions were:
Try changing some advanced wireless settings on the router.Connect the computer to the router with the Ethernet cable. Open the setup page of the router.Click on wireless tab and set the configuration view to manual. Change the wireless channel to 11. Save the settings.Go to wireless tab and click on Advanced wireless settings.Change Beacon interval to 75, RTS threshold to 2307 and fragmentation threshold to 2306. Save the settings.Try to connect to the wireless network again and see if that works.
1 - I think my computer already is connected to the router with the Ethernet cable - I mean there is an Ethernet cable attached to both my computer and my router - in slot 1 on the router
2 - the only thing I know how to access is the Linksys EasyLink Advisor. What and where is the setup page of the router?
View 4 Replies
View Related
Dec 20, 2011
I am running a WRT320N with Firmware 1.0.04Trying to Upgrade the Firmware to 1.0.05 it always fails at about 24% progress with a message saying an invalid value has been entered.I downloaded the firmware from your homepage twice so that the file is not corrupted
View 4 Replies
View Related
Feb 17, 2010
I have some major problem with my WRT320 router. For some reasonit won't let me connect to Age of Empires 2 (other, newer games work fine) via Hamachi. When i want to connect i can see the game but when i want to join it tries to connect but fails telling me i'm unable to join... I know the problem is in the router because when I connect my modem directly to my computer Age of Empires connects fine!
View 8 Replies
View Related
Oct 19, 2011
We have WRT320N (Model No.) and when I moved i notice that my wirelss network does not have internet connection. Even after I hook everything up it doesn't work, my computer does not recognize the network but the laptop does. I have prior knowledge about computers and the internet but I don't know why I am having a problem. Is it because I moved and the data in my previous home does not match the data here?
View 3 Replies
View Related
Aug 22, 2011
I'm using my WRT320N as a home router, I need more ipadresses to be delivered to my computers, yet I can't get my router to give med wider netmask range. In the list I get 255.255.255.0 - 255.255.255.240 or something like that. I need 255.0.0.0 on my network and that would be perfect if i could get that...
View 5 Replies
View Related
Aug 7, 2011
I've got the below setup, have the wrt320 setup as a switch / wifi ap, i'm totally unable to access its management page from pc1 but am able to via pc 3, why is this, how can i get around this? Routing? Also am unable to access pc3's resources from pc1..When i enter the ip of the wrt320 it thinks about it and before it has come up with the user/password screen but it soon dissapears and firefox comes up with a "Unable to connect Firefox can't establish a connection to the server at 192.168.0.2." message.
View 1 Replies
View Related
