Linksys Wireless Router :: Desktops Dropping Wired Connection To E4200
Jan 2, 2012
I lost all Internet connnecitivity on my Linksys e3000. After determining that my cable modem was connected and working correctly, I pulled the e3000 and put my old wrv54g router in place. Wireless worked, but all wired connections showed link but no other apparent connectivity. Neither of my desktops could get a DHCP lease.
At that point, I purchased and manually installed a new e4200 router. All worked fine. Both laptops connected via wireless and both desktops via my house LAN. Until this morning (Monday). Wireless is working just fine, but both wired computers show 100 Mbs connections on an unknown network with no DHCP. Checking status shows packets going out, but nothing coming in. Checking LAN status on the router shows that both ports are connected, but it does not appear to receive anything from either desktop. All was fine last night. Oh, the router is on 1.0.03 firmware.
I have tried about everything I can think of. Configurations both on the router and the desktops (one Windows XP, 64 bit and one Windows 7) and all seems fine. I have disabled and reenabled the network connectors, rebooted both the router and the computers, etc. Nothing seems to work.
View 5 Replies
ADVERTISEMENT
Jan 6, 2012
I have a Linksys WRT120N with two desktops connected via wired connections.In the house, there are two students accessing the Internet through WiFi via the WRT120N.One of the laptops (on an Apple laptop) seems to lose its' connection from time to time.The other laptop (Lenovo) is located the furthest distance from the router and only gets two bars signal strength.Would my best option to improve the signal strength for the Lenovo laptop and hopefully, also increase reliability for the Apple laptop be to purchase a new router such as a Linksys E1500 with speed boost or would it be best to try a Linksys range extender (RE1000)?
View 2 Replies
View Related
Nov 15, 2011
I bought a e4200 router about 3 weeks ago and after a power outage it decided it didnt like being connected to the internet anymore. So i got on the phone with cisco they determined the router was no good, mind you my laptop would connect wired. So they sent me a "refurbished" one, so i set it up. The new setup was wonky because it said the same message "Your connected to your router but..." then after trying to get the connection its self and failing it came up with "congratulations you are now connected to the internet". That lasted 3hrs and 45mins then died, so i went upstairs to power cycle it, it decided to connect with the old settings. That lased 25mins then died, so i reset it and reconfigured the router. Wouldnt connect, i checked my mac address and it was using my wireless one and kept turning on my wireless connection durring the install. So i cloned my wired mac address and got the internet for roughly an hour... then it died. So i reset it again and kept the wifi off got it going and decided to go to sleep. I wake up and its still working after 8hrs, i go down stairs with my tablet and i dies again. This time it refuses to reconnect, refuses to reset back up just doesnt want to work.
View 3 Replies
View Related
Feb 4, 2011
I just got an E4200 and have a SBG6580 cable modem. I cant seem to set this up properly and my connection keeps dropping. What is the proper set up ? I would like to configure it so the cable modem handles the DNS and the E4200 handles the wireless.
View 4 Replies
View Related
Jan 15, 2012
ever since i had a power failure losing all power in my apartment, my router has begun regularily losing connection to the internet, I have to go into the router and renew ip address which is quite annoying
[code]....
View 6 Replies
View Related
Jan 2, 2013
I have e4200 router and i notice sometimes when i am browsing that dops connection.
View 9 Replies
View Related
Jun 10, 2012
my e4200 wireless. I have internet connection speed of 40mb and I have epc 3925 working in bridged mode as modem and E4200 as router. When I connect my laptop with wire on e4200 I am getting 37-38 Mbps on speedtest.net which is perfectly fine. But on wireless I am having a lot of dropping of speed: I have 2mps then jumping to 5-6 Mbps and so on it never goes more than 5-6 Mbps. When I disable WMM Support in QoS I am having perfectly constant 20mbps but... I have only g network 54mbps. [code]
View 9 Replies
View Related
Apr 2, 2012
I have a home network with a Linksys E4200 connected to the ISP's fiber box. The problem is that when I'm connected to the Linksys, either wired or wireless, the connection to the internet will drop after what seems to be a random amount of time (normally anywhere from 2-10 minutes). I can restore the connection by doing any of these things:-reboot Linksys-disconnect and reconnect cable from router to fiber box-if on wireless connection, make changes to the router wifi settings, like change the wifi channel.The internal network stays up, and I can ping both the internal and external ip of the router, but not the fiber box. I have also had the same behavior with an Edimax Wifi AP and less frequently with a Edimax router (once every 1-2 days). I have done everything I can think of:-changed the wifi channels-changed the ip ranges, subnets, turned router DHCP off and back on-booted the fiber box-changed cables-updated all routers to the latest firmware, the network cards with latest drivers...and loads other things that I don't remember right now. For the wifi side of things, there are no other networks in range that could interfere. The same problem occurs on both my and wife's Win 7 laptops and on the iMac (latest OSX). Here's a fun detail: while the Linksys has lost its connection to the internet, I can still access the internet through the old Edimax router connected to the same fiber box, either wired or wireless.
View 1 Replies
View Related
Jul 17, 2012
I've recently picked up a E4200 to build a dual band network which is targeting to link up (TV, media server, ps3, laptops) then (maintaining phones etc which only has b/g). While currently only laptops.Before doing any of these I have another cisco modem router DPC3825 which worked fine with giving wireless access.I first attemped to leave the modem router has is and connected the E4200 (ethernet 1 to internet), and changed ip to x.x.0.1 and x.x.0.2 while disabling wireless on the dpc3825 and the DCHP on the e4200 and have default gateway to x.x.0.1. My laptops can connect to wireless on E4200 but it couldn't get internet access.
Then I tried turning the modem to bridge mode & resetted E4200 (factory setting x.x.1.1, auto DHCP), and then connected my devices to both wireless bands. At this point I see router status obtained ip from ISP and Internet reached full speed per ISP's mark but the connection only held up for about 1 minutes. I noticed all the devices still maintained connection to router wirelessly but the router loses internet connection (lost the ip and couldn't get it back).
View 4 Replies
View Related
Mar 30, 2013
I just had Comcast setup my internet and it is really fast. 30 down, 10 up, 40 ping, my connection to my computer (wireless) is very fast and my online gaming (wired) is not laggy at all.The problem lies with the connection dropping when I am online gaming. I connected directly to the modem and there's no problem at all. I connect to my Linksys EA3500 and once I start playing in an online game, I disconnect from Xbox Live and am dropped from the game... anywhere from right away until about 10-15 minutes into the game. This is the only time where my connection falters at all, otherwise it is great. But I play online a lot, and competitively, so I obviously need a stable connection.I have not had this issue with my previous ISP in New York, Time Warner and that connection was much worse. I'm thinking it must be a setting on the router that is causing this, but I can't pinpoint what. I tried automatic AND static connections from my xbox to the router. On the static connection, I even put a DMZ on it, but to no avail.
View 9 Replies
View Related
Sep 6, 2011
Can we disable wireless totally in E4200 and just use wired connections? I didn't see any configuration for that, but just in case I missed it. I'm also aware we can disable SSID Broadcast.
View 1 Replies
View Related
Feb 13, 2013
I have a strong internet signal with good SNR coming out of my cable modem, then a nice short 3ft cable going to my linksys VOIP router (I think it's a SPA 2102). Whether I have anything downstream plugged in or not, the "phone" light on the VOIP router goes off every once in a while and when I check I find that I've lost both dial tone and Internet - basically everything downstream of the VOIP router. Have tried every variation on configuration you can imagine (feeding just one phone, feeding the entire phone wiring to the house, nothing at all plugged into the phone jack, no computers downstream plugged in, replaced all the cables, ...). I've replaced BOTH the cable modem and the linksys VOIP router and the problem continues. My cable company says my signal is fine. They suggested a signal amplifier but the coax comes straight to the modem, no splitter, and I'm always seeing 6-7dBmV. My phone company says their router must be losing signal upstream and refusing to reconnect, especially now that we've tried replacing their VOIP router with no change. Any chance I got two 'bad' routers in a row? Not sure what they did for setup parameters. I'm not particularly tech-savvy but have read a lot since seeing these issues, have run my own ping and tracert checks and everything seems to be wonderful... but then most of the time everything IS fine. When I have phone it's crystal clear and when I have internet it's nice and fast. I sometimes go 24hrs or so without a drop, but other times I'm resetting 2-3x in a couple of hours. All I do is power off the VOIP router and back on and everything is fine, for a while. After first getting VOIP things were fine for 4-6 weeks.
View 1 Replies
View Related
Feb 4, 2013
For a number of months now, our Internet connection in an office of 5 computers, 2 Macs, 3 windows boxes (1 as dell laptop) has experienced the connection of the Internet dropping off.The timing of the 'drops' is usually in the morning, when the Dell Inspiron M510 either boots up or wakes from sleep. Typically the solution is to turn off the modem, the router and switch, wait a few minutes, then turn the switch, the router, then the modem back on. Our connection via the modem is through AT&T, via a non-static IP addy.Our router is a BEFSR41, v4, with firmware up to date (circa 2006) It's becoming a daily chore now, just about, and is getting to be a bit of a headache on some days.
View 3 Replies
View Related
Apr 21, 2012
I saw one post recommending to changing the MTU from 1500 to 1400. That did absolutely nothing. My comcast internet is now slower than 14.4 dial up modem I had 16 years ago. The strange thing is I can sometimes download at over 2 mbps with torrents. It's mainly loading websites where the speed is so bad.
View 9 Replies
View Related
Oct 21, 2012
I seem to all of a sudden be having some strange issues with my E4200. I am running Firmware Version: 1.0.05 . I am also using a Dlink DAP-1522 gigabit bridge. The main machines I am noticing the dropouts on are my main windows computer (connected to network via ethernet cable plugged into DAP-1522 bridge) and my wifes ipad. What happens is it drops connectin for about 3 minutes then comes right back. I am really perplexed as to what could be causing this. At first I would have thought it was a bridge issue but thats up to date and my wifes ipad dropping (which is connected via wifi) shows there is something else going on here.
View 9 Replies
View Related
Mar 16, 2011
my e4200 updated with latest 1.00.1 firmware is constantly dropping connections from the outside to existant lan servers running low traffic services when my machine is using torrent or internet gaming.( call of duty modern warfare )
View 9 Replies
View Related
Nov 11, 2011
Had E4200 for several months worked great. The last 3 weeks speed drops intermittently through the day.Up graded to latest firm way yesterday 11-10-11 still have the issue, i.e. first thing this am had 15mbps and 1 hour later was below 1mbps. Have not added anything new equipment or software wise in the house during this time.
View 2 Replies
View Related
Apr 1, 2011
e4200 internet keeps dropping
View 9 Replies
View Related
Apr 11, 2011
my E4200 is dropping connections several times a day. I'd be working on my laptop, go to a webpage and bang, no connection. A minute or so later it would reconnect. It even appears to be doing this with a computer that is hardwired to one of the ports. So it doesn't seem limited to just wireless. Happens to both N and g channels as well.
View 9 Replies
View Related
Nov 18, 2011
When watching Netflix, I can get 5 to 15 minutes of a movie no problem. Then I will get an error message:Cannot connect to Netflix. try again later. If the problem persists
- try again
- exit
Then I can watch a few more minutes and it stops again. And again, and again......I have cable inernet service (Brighthouse Communications), with the E42000 connected to the cable modem. Then I have a Panasonic WiFi adaptor (DY-WL10) plugged into a USB port on my Panasonic Viera TV. I have the latest firmware on the router (1.3.03, build 14).I have done the routine of re-cycling the network by re-setting the router (and re-setting it up) and the modem.The chat session guys had me do the following:
1) Uncheck “Filter anonymous request”.
2) Click on Setup Tab - Here you will see MTU.
3) Select Manual & set the size to 1364
4) On Wireless tab, clicked on manual, change the Channel for the 2.4 Ghz network to 9.
5) When we tried it on the 5Ghz wireless they had me set the channel Width to 40MHz Only, and set to channel – 161
I also tried setting up port range forwarding. He knew the port information, and walked me through it.I have re-set the router to factory default settings, re-installed the software, and tried the previous steps twice more (except the port forwarding, because without my friend, I am not sure exactly how) I know enough to not have multiple WiFi devices going at the same time while trying to watch Netflix, but I know that I get good WiFi download speed tests at the location of the TV with an iPad (3.6 MBPS).I have done troubleshooting on the internet service. It has a good, strong continuous uninterrupted speed.I have tried this on two different TVs (similar Panasonic models, bit with the same WiFi adaptor). Problem persists on both TVs.I tested it with a 50’ LAN Cable running from the router to the TV. Netflix worked when wired!Next test I want to do is to stream Netflix on the iPad, right at the TV and ensure that works.To me, this seems like a wireless router setting issue or an issue with the Network Adaptor, or an issue of communicating between the Router and the adaptor.
View 6 Replies
View Related
Jul 30, 2011
I recently bought an E4200 and noticed that the wireless speed keeps dropping as it stays connected.As soon as I power it on, my iPhone and notebook connect at 54Mb, but as they remain connected, the speed keeps dropping to 48, 36 and one morning, my phone was oscillating between 5 and 11. The iPhone was almost at the same spot, and the signal was around 85~95%. On my 3 year old DIR-300, the speed don't change at all, and it's in a place where I can see around 15 connections. On the E4200 I can only see 2 other networks.I've already tried switching channels, fixed and auto channel, updating firmware and a few other common configurations. At first, I thought it was my repeater, but I turned it off and it didn't work. Turn my cordless phone off didn't change it also.
View 3 Replies
View Related
Jan 23, 2012
I just installed a brand new e4200 replacing my WRT54.Wireless works good with a noticable performance improvement over my old wireless.However, the wired conenctions are not solid at all. I am getting over 10% packet loss from the wired conenctions.I can not even connecct to the web ui reliably over wired connections.I upgraded to the latest firmware release with no real change at all.
View 2 Replies
View Related
Sep 28, 2011
I've had my 4200 for about 1.5 months now and it was working great until 8 days ago. I was playing WoW over wireless (like I always have) and noticed that I was lagging a bit. I brushed it off as possibly my internet connection. The next day I was surfing the net and at random times webpages wouldn't load or would take longer to load. I checked my wireless connection properties in windows and noticed that the link speed drops out every now and then. It'll start at 54Gb (only have G in the house, so I disabled the 5GHz and set 2.4GHz to B/G only), then it'll drop to 48, 36, 11, 1. Meanwhile the signal doesn't drop a bit. I'm still connected to the router just the link speed drops out and it just started. It's very annoying having to go old school and hook up wired on my laptops just in order to chat online or anything. I'm still using v 1.0.0 firmware, so I guess I could try upgrading to .03 and see. But I personally doubt that is the issue since this just randomly started happening. I ordered the router through newegg.com and I do not have the box for the router anymore so I don't think I can return it. And I can't be without a router for 4-6 weeks while Linksys/Cisco repairs mine.
View 5 Replies
View Related
Oct 11, 2012
My E4200 router no longer accepts any WIRED connections. I can connect from the modem to the computer and everything works as expected. I can connect other computers wirelessly to the router. I cannot connect any laptops WIRED to the router. Nothing has changed on the systems to restrict internet access. There is something wrong with the router and the WIRED ports. I tried going through the troubleshooting on this site but it was of little to no assistance. The Cisco Connect utility doesn't appear to accomplish anything either. My guess is because I cannot connect to the WIRED ports on the router to connect to the internet to allow for whatever troubleshooting that needs to be done.
View 2 Replies
View Related
Feb 8, 2012
Had an E4200 for a couple of months now and have not been able to resolve an issue with the router dropping an Apple iPad 2 at random times.The E4200 is replacing a Cisco Aironet 1200, which never dropped any clients, iPad 2 or others, and never displayed any of the issues below.
TECH DETAILS:The E4200 is being used purely as an access point. All extras are not in use and are disabled.
Firmware 1.0.03
Hardware version 1.
BASIC ISSUE:The E4200 drops an Apple iPad 2 off the 2.4 Ghz Mixed (B, G, N) network. The user must then select the network to rejoin. Rejoining occurs without incident. The same issue occurs when the network is restricted to B, G. The drops occur at what appears to be random intervals - sometimes 10 minutes apart, sometimes hours apart. We can have as many as 6 drops in an hour. A ping to the apple ipad shows the device stops responding to pings about 10 seconds before the user is prompted to rejoin a network. Meanwhile, a ping to the E4200 itself from a laptop connected via the E4200 on the same radio as the ipad continues to work without fail during this incident.
1. The iPad 2's cannot connect to the 5Ghz radio. I believe iPad 2's are supposed to support 5Ghz.
2. Both our Apple TVs do not connect to the 5Ghz radio: they fail with a "There was an error connecting to the network. Check your settings and try again. (-3914)" error. Apple TV supports 5Ghz.
3. The admin interface for the E4200 is very slow sometimes. Probably over 20 seconds to render some pages when it gets really bad. As a comparison, Internet-based pages on fast sites that delivered via the E4200 itself load in less than 2 seconds.
4. The HTTPS version of the admin interface can only be connected to via Safari browers. Both Internet Explorer 9 and Chrome 16 fail to connect with a "Connection reset" error. In Chome, it says "Error 101 (net::ERR_CONNECTION_RESET): The connection was reset." This is across multiple devices. There is no issue with straight HTTP.
All other devices - including Macs and PCs - connect fine with the E4200 on both 5Ghz and 2.4 Ghz radios, even if they cannot access its admin interface via HTTPS.I've presented quite a few issues above, but the main one is the drop outs for the iPad 2 devices. I'd present logs on drops, but the thing doesn't record any useful logs.
Basic wireless config:
5Ghz:
Network Mode: Wireless-N Only
Channel width: Auto (20 or 40 Mhz)
Channel: Auto (DFS)
SSID Broadcast: Enabled
[URL]
View 9 Replies
View Related
Dec 16, 2012
I got an EDIMAX Nano BRN-6258n Router to replace my glitchy Belkin Wireless-G router about a month ago. My typical network setup involves a desktop computer wired to a router and a laptop connected wirelessly.
Anywhere from once a week to twice a day, the internet connection starts (selectively) dropping off. While I cannot browse the web, some of my browser add-ons and Skype/Dropbox are working fine, and Windows almost always indicates a perfectly working connection.
If I am streaming through YouTube or other sites, the stream continues to play after the connection loss.
For AV, I use a combo of Malwarebytes and AVG Internet Security.
View 2 Replies
View Related
Sep 27, 2011
I have this E4200 for about 3 months and allways has been used as an wireless router. Today i wanted to connect 2 wired computers to it via lan and whatever i do dosnt connect. Dosnt even let me acces the 192.168.1.1 page to router settings.I am on firmware 1.0.02, i also did a full reset and then did set up with cisco connect, did try that thing with the cisco usb connect and still no joy with the LAN conection.
One comp uses win 7 the other is on win xp. I can connect both comps succesfully to other router via the gigabit ports but not to this one.
View 3 Replies
View Related
Aug 10, 2011
I see on the control panel that there is MAC filtering for the wireless connections. I don't see a similar control panel for computers that are wired directly to the router. Where do I find this?
View 3 Replies
View Related
Jan 12, 2013
my general internet connectivity with my e4200.I have a new but similar problem today with the same router.After powering down equipment and moving it around, my wired connections all error. Error in that they will not get an IP address nor will they connect to the internet or each other.My wireless connections still work flawlessly.
I tried powering down the devices over night (to avoid any heating issues) and then powering up but the results are the same. I am obviously missing something, and don't really want to start my network from scratch again...
View 5 Replies
View Related
Dec 8, 2011
I have an E4200 router & am trying to get it to work with ATV2 through HomeSharing & iTunes. It works fine when my PC is wireless & the ATV2 is wireless. BUT, when the ATV2 is wired via ethernet & the PC is wireless -- nothing!
PC is Win 7 64 - SP1
ATV2 is 4.4.3 (3323) and the router is:
E4200 is 1.0.03 build 14
View 4 Replies
View Related
Aug 24, 2011
Installed E4200 with an iMac running MacOS X Version 10.6.8. Wireless connection works great. Also connected a wireless laptop without a problem. But can't connect a 2nd computer is wired. That is a PC running Vista. I know the wiring is good, because the E4200 is a replacement router in a network that was working fine.
View 1 Replies
View Related
Oct 29, 2009
I have a WRT310N wireless router (Ver 1). In the house we've got 1 macbook, 2 laptops running windows vista, and 2 desktops running windows XP.The original problem is that both desktops will not connect wirelessly. All 3 laptops connect but neither desktop wants to connect. Most of the time neither desktop will even recognize the wireless network. On one of the desktops we bought and installed a linksys wireless-n pci adapter. It was installed using the software that came with it and the drivers were updated. It still does not recognize the network or connect (obviously).
This has led me to try to upgrade the firmware on the router. The firmware version it is currently running is 1.0.4 (Jan 3, 2008) and I have been trying to upgrade to 1.0.7. I downloaded the firmware update from the linksys website. I accessed the router via my browser and went to the "Firmware Upgrade" section under Administration. However, the upgrade freezes at 98% every time I try.
I have tried to upgrade the firmware wireless, wired, and wired without internet connectivity and nothing works. Fortunately stopping the upgrade after the freeze at 98% has not had any negative affects on the router as it still works perfectly on the 3 laptops. I even re-downloaded the firmware .bin file before the last attempt and still nothing.The fact that neither desktop will connect wirelessly is baffling, but I don't know what to make of the fact that the firmware update freezes at 98%. I've looked for the intermediary firmware updates to see if I could step my way up to the latest update, but I haven't been able to find them.
View 4 Replies
View Related
Jul 14, 2011
I'm trying to fix the network at a student housing building and the system is kind of a mess. We bought a new E4200 to replace our old Linksys router which no one knows the admin pw to. We have four switches for 50 connections throughout the four story house and when switching the connections over to the new E4200 all of the wired connections no longer work. Switch back to the old router and presto. How do I need to change the settings with the E4200 to get it to work?
Also, as it's a thick old house the E4200's wireless only covers maybe half of it...I purchased two wireless repeaters to put on the 3rd and 4th floors, are these simple to install with the router?
View 4 Replies
View Related
