Linksys Wireless Router :: VOIP Does Not Work Via E4200?
Jul 25, 2011
I have a new Polycom Soundpoint IP550 VOIP phone that was not connecting via my old WRT54GS router. I purchased a new router, the E4200, thinking it was just the age of my original router. It also will not allow the VOIP traffic through. I can connect the VOIP phone directly to my CenturyLink modem and it works. But when I connect it back to the router it stops.
I contacted Cisco support and they had me upgrade the firmware to 1.0.02 build 13 May 24, 2011 version. Also adjusted down the MTU to 1364. That still did not work so they told me to take the router back to the store. I have not done that yet as I want to ensure that the router is really broken and not that I am missing a setting. The tech said that I should be able to plug the VOIP phone into the router and make NO additional changes.
How to set up RVS4000 QOS settings to work with a VOIP phone system? I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection.
I just purchased a new E4200 router. When I try to set it up, , it says that my software (Lion v. 10.7.2) is unsupported. Is there a download that will allow me to use this router?
I set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
I have an HP LJ4050 plugged right into one of the open LAN ports on my E4200 with a CAT6 cable. Can this router work as a LAN print server? I can't pull up the IP on a browser window or ping it successfully.The 4050 doesn't have USB capability and I don't want to use the parallel port on my PC unless I have to.If possible, I'd like to have wireless computers on the network be able to print to it as well.
why Windows Backup in Windows 7 pro 64 would not backup over the network to a drive I have connected to the 4200s USB port? Everytime I run it I get a Access Denied error at the end, even though data has been transfered. After about 5 hours of searching both here and Microsoft's website, I just get lots of people with the same issue that hasnt been resolved anywhere consistantly.
I have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
I'm looking to purchase the E4200 and use an external HDD with enclose as a NAS (probably just a backup drive), specifically this model. [code]The HDD would be a 1TB Samsung Spinpoint F3.Does this router allow for USB 3 connections or at least fallback to USB 2? The first comment on the external enclose says so otherwise.
Model name: Linksys E4200 Model number: E4200 Firmware version: 2.0.36.126507 Operating system: Windows XP SP 3 Software version: 1.4.12005.2 Connection type (WAN): DHCP
My Canon MX882 multifunction printer is connected to the router via USB cable. The printer works. The scanner does not work.
I have tried both old firmware (2.37) then the Cloud firmware and now back to 2.37 again. the parental controls seems kind of fool proof but anyhow they dont work for me.If I set the internet access as denied at certain times, if the client is already connected when that time occours, it can continue to use internet (until it disconnects and tries to reconnect). Happens almost every time. And the biggest problem is that if I try to block internet access for a device like a cell phone, even though the user can not access the internet through the web browser, apps like Facebook, games etc can still access internet. Kind of useless parental control?!But I have tried to reset, reflash etc.Also I find this router pretty unstable, the only device that works flawless is my iPad (3), the laptops and cell phones at home loses internet connection every one and then, even though it seems like they have good connection to the router. Never been a problem with my earlier routers.
I'm having a problem with Wake on Lan. (I'll bet you never guessed from the title, eh?). I have an E4200 and I can not get WoL to work over the internet.(I'm assuming it's not actually going out to the internet when I wirelessly wake it using shawn.dynamicservice.com and the subnet, but rather the DDNS name is being resolved through the ARP cache, but I don't know. I'm still learning) Consequently, if the sentence above in parenthesis is correct, I am unable to perform WoL from outside my LAN. What am I missing?
I'm trying to fix the network at a student housing building and the system is kind of a mess. We bought a new E4200 to replace our old Linksys router which no one knows the admin pw to. We have four switches for 50 connections throughout the four story house and when switching the connections over to the new E4200 all of the wired connections no longer work. Switch back to the old router and presto. How do I need to change the settings with the E4200 to get it to work?
Also, as it's a thick old house the E4200's wireless only covers maybe half of it...I purchased two wireless repeaters to put on the 3rd and 4th floors, are these simple to install with the router?
I just got the e4200 the other day and everything has been great except I can't seem to get my ABS megacam 4 ethernet camera to work.It was working fine with my old router, and if I plug directly into it it works, but I can't access it through the router at all. I can see the camera in my routers client list, the camera is set to DHCP and it is assigning it an IP address but I can't connect to it. From my desktop pc (wired) I can using the IPwizard software that came with the camera and it will see the camera on the network but it wont connect to it, my wireless clients can't even see the camera using the same software.
I recently bought myself the E4200v1 router, and have had several issues with it. One issue I cannot seem to find a workaround for is the wifi bandwidth problem.I have a 100/10 mbitl internet connection. The router claims to support 300/450 mbit speeds over wifi, so that should be plenty. in reality however, that isnt so.Even though my N-standard wifi adapter on my machine states it has a 130 mbit connection to the router, I consistently test the internet throughput when using wifi and speedtest.net to around 20-21 mbit. If I put in a cable, I instantly get full speed, 100/10 mbit.
Have to add; I am not new to the networking game, I have a CCNA and a degree in computer sciences, and work with hosting web sites using cloud tech every day. At this point, I have tried everything related to settings on the router, so I can only conclude that there's some kind of bug in the firmware. I would expect the standard firmware to work, and not having to install DDWRT or other custom firmware.
I have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
On my new E4200v2, after I tried to move beyond the disappointment of Cisco removing Internet Access Policy entirely, I decided to give the stripped down Parental Controls a try.
Sadly, I didn't have any luck doing what I needed to do... block my Tivo's from accessing Youtube.
I enabled Parental Controls, Added the Target Devices (my Tivo's did show up), and added "Youtube.com" as blocked site #1. Saved. Entered the parental password when prompted. Even rebooted the router.
But Youtube wasn't blocked. So I added to the target list a non-Tivo device (a Macbook) for a reality check, and rebooted the router again... still no luck. Youtube still not blocked.
So then I started to wonder if their Parental Control depends somehow on the local DHCP server & Client list. Because my E4200 has DHCP Server = OFF (I have always used a Windows Server for DHCP).
I tried to call Linksys support to get this working, but after 45 mins, including escalation to senior engineer, they really were pretty useless (no real familiariarity with my problem) then they disconnected my call!
I have Linksys configured with IP 192.168.0.x and my local network ip 192.168.1.x have firewall connected to Adtrans box that gives us internet access via T1 line and other port is connected to the switch. Wireless router is connected to the switch using internet port.I can connect to wireless using iphone but emails don't work when connected to wireless. I tried to connect laptop to wireless is does not connect.
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
I have the e4200 and I am having trouble getting DHCP reservation to work properly with my Windows 7 machines. Perhaps there is a step that I am missing. Basically I go to the DHCP reservation setup page, select my machine and add it to the reservation table. Then I save the changes. As soon as I do this my computer goes offline. If I reboot my machine, it is still offline. I've tried the same procedure to reserve the IP address for my phone and it works fine so I wonder if the problem is with Win7.
Is there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
I have a E4200 router and I was using it with a 1st generation MacBook Air for internet and also had my Samsung laser printer hooked up (USB) for wireless printing. It worked perfectly. Now I have upgraded to a new MacBook Air. The internet connection works fine, but printing won't work. Same printer. Same connections.
Do I need to refresh/reboot something? My new Mac has the printer driver. I get a message "printer if offline" "printer is not connected" -I feel like the router now does not recognize the new Mac's command to print.The older macbook air still works and prints wirelessly. The new one does not.
I purchased Linksys WAG160N (from a store) and I also have 7 Linksys SPA962 VOIP phones provided by MyNetPhone with service included. All tests we found out that this modem doesn't work with this VOIP phones. Somehow probably doesn't give access to MyNetPhone servers to get connection with this phones.I purchased an other one from DLINK and works perfect?
I have a DIR-825 since a couple of days, Hardware version B1, firmware 2.01EU (date Fri, 12, Jun, 2009 = latest european firmware) Have portforwarding for ports 25, 80, 443, 143, 993 via virtual server to a local linux server (192.168.0.3)
My (SIP protocol) VOIP phone (192.168.0.100) does not work anymore since I use this router. It worked fine on my old WRT54G. The phone logs-in normally at the voip provider but when I make a call, it seems that the ports are not forwarded or are blocked by the firewall. I have tried to manually setup portforwarding and virtual server instead of portforwarding.
I have tried many things, from disabling QOS, SPI, end point filtering and more but it does not work. I have also programmed DMZ for my ip-phone, but it does not work. Nothing found in the logfiles about frame drops. (I have setup a syslog on my linux-server)
There seems to be a bug causing frames dropped, as my setup has always worked with my WRT54, and should work with DMZ set, but it does not. The same setup works fine on a DIR-655 of a friend.
I have a VOIP WiFi phone (MIC505W) I have configure it according to the user manual.I get access to WiFi, but when I dial a number I get busy signal with the message "disconnet".
I have a static IP on the ATA (Linksys PAP-2T) ...the router will only pick it up occasionally...most times it does not. The ATA is on and working (I can call in/out) but I can't see how the router can't find/see it. I have added the ATA to the DHCP reseve list but still nothing. I have the port fowarded for the ATA but when I go to canyouseeme.org it comes up as "Connection timed out"...becuase I think it can't see the ATA behind the Router.
I can't get my VOIP ATA (linksys SPA-2102) to work properly with the shiny new DIR-835. I updated the firmware to 1.02 and messed around with various settings but it just won't work. Well, I can get registered and everything looks ok but, when I receive a call, the person at the other end can't hear me. I can hear them fine, but they can't hear me. I don't have any problem when I call someone. Still, it is frustrating. The problem persist even though I put the ATA in the DMZ.
A client is using Tmobile VOIP using the aforementioned WRTU54G-TM 2-line VOIP wireless router with 4-port hub. What they would like to do is to place this in their network and NOT have it change (route) the network addresses being assigned to devices 'behind' this router so even their wireless devices are all "on the same network" as the wired devices BEFORE this unit, In essence, preserve the same 'network and subnet mask' that is being issued by their DSL router via it's integrated DHCP server. ... Rather like operating this unit like an 'access point' instead of a router.Under most circumstances, I might try to assign this router a static IP outside the scope of the DHCP range the DSL router would supply, then plug the (gigabit) Ethernet network cable into one of the 4 Ethernet ports on the rear of this router - but apparently this does not 'facilitate' a connection to Tmobile's VOIP service.When attempting to do this, the connected telephone devices do not get a phone line connection and the status light(s) that normally indicate proper operation do not illuminate.
I have installed the LinkSys E3000 Router, but I am still struggling because the device Gigaset Siemens C410 (that is the VoIP base) does not work.Before the E3000 I had an WRT160Nv2, with this router the Voip Devise works properly. If I link the WRT160Nv2 to the E3000 and the VoIp device to the WRT160Nv2 it works.
I use in my network Linksys 4200v1 (newest firmware) and Sipura SPA 3000 ( 3.1.20(GW)firmware) and SPA 122 (1.1.0(011) software version as my phone adapters.My voip phones are working great until I start to download or upload some files, watching on-line tv.How and where should I set up above routers to have the same great quality voip while uploading and downloading at the same time?
