I set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
View 9 RepliesI use modem and router to connect to the internet.When I connect my PC directly to modem port forwarding is working.When I connect my PC through my router the port is closed. I followed instruction for port forwarding.
View 9 Replies View RelatedI am trying to port forward my Linksys e4200 router v 1.0.04. However, it is not successful for when ever I check if the ports are open they fail they test.
I am sure that I am doing the actual port forwarding correctly (I hope), but something is refraining the ports from being open.
I'm a happy user of the E4200 for a few weeks now, and all in all it's a very robust and useful router.Within my network I have a webserver running using both HTTP (TCP 80) and HTTPS (TCP 443). I want to make this webserver available to the internet and so I configure port forwarding to forward port TCP 80 and TCP 443 to my internal webserver. As soon as I now apply these settings, I loose connection to the webinterface of the E4200 and get connected to my internal webserver. I would expect the router would only forward connections coming in through the external interface of the router, however this is apparently not the case (or at least not in my setup). So I tried setting up remote management on a different port to at least allow me to remotely manage the router, but this does not work from my internal network.
Right now, I'm assuming I'm doing something wrong, or have miss-configured something. Is it possible to switch the webadmin port to a different port (like 8080 and 8443)?
I have a Cisco E4200 with a Thecus NAS behind it. I configured port forwarding on port 80, 1080 and 4433 to access the NAS. However it's not working. Also tried to place the NAS in DMZ, but also I cannot connect it from outside my network. Inside my network, there is no problem.I also connected the NAS directly to the internet, and then I can access it from outside my network.I already tried a factory reset, disabled UPnP and IPv6, but nothing seems to work. I also replaced the router with a Cisco E3200, but it makes no difference.
View 9 Replies View RelatedI have a e4200 router, And a 660 series modem, I'm trying to portforward for a game called minecraft, I cannot seem to get the ports to open, I've called Century link they told me to put my modem in to bridge mode, So I did they said my IP should be public not private now, It is still private
View 6 Replies View RelatedTrying to setup port forwarding for an XBox 360. Set fixed IP on XBox using IP outside DHCP range. DHCP range is .50 to .80. Set XBox to .49. Gateway is .1. Mask is 255.255.255.0.Added four port forwarding rules per directions on xbox site and also portforwarding.com for ports 53, 80, 88, 1074 to the static IP Turned off DMZ, Turned off UPnP, Turned off SPI. Windows firewall is on, running XP Pro SP3 and Win 7 Pro on other devices.Making the rules active for the fixed IP shuts off internet access for other devices.Single router (E4200 V2), switch, then remaining devices. Private IP addresses in the 192.168.xxx.xxx range. Rebooted router, same issue. What am I missing?
View 9 Replies View RelatedAt the E4200 there is a limit of (free to make) 15 Single port forwarding and 15 port range forwarding to fill in.I get as suggestion that I must give up a total range of ports where all the ports I use where in.But for security reasons I will not do that.
View 1 Replies View RelatedIPort forwarding simply does not work with this rounter on Comcast. I called comcast to see if they were blocking ports and they insist they ARE NOT.So what can it be? Was on FIOS with their modem/router combo and port forwarding worked like a charm with them.I've tried single port forwarding, port range forwarding, yada.
I am using the correct internal IP address on the machine I want to enable port forwarding on..Latest firmware is installed 1.04 or whatever (just purchased the router and updated during the Cisco Connect install on the 29th). Guess I should go find a cheaper router that actually works...
i have a WRT160N V3 and DMZ or Portforwarding dont work.i tried locally following
WAN_PC-> WAN-PORT -> WRT160N V3 -> LOCAL-PORT -> LOCAL_PC
The WAN_PC has a Static-IP 192.168.1.2, Subnet 255.255.255.0
The WAN-PORT has a Static-IP 192.168.1.1, Subnet 255.255.255.0
ON the WRT160N V3 i configured a DMZ on 192.168.0.100.and Disabled the Firewall.
On the LOCAL_PC (192.168.0.100:8888) is a Apache
So when i type 192.168.1.1:8888 on the WAN_PC i get NOOO Website from the Apache on 192.168.0.100:8888?
I have done this before on this exact model about a month ago, so it's still fresh in my mind on port forwarding. (note, I'm using firmware version: 1.0.00) I am running a windows 7 computer wirelessly using this router.What I do for port forwarding is type in router IP (192.168.2.1) in internet explorer, type in "default" as username and "admin" as password. I click the "applications and gaming" link which brings me to port range forwarding.
I fill in my port info, in this case a mine craft server running on 25565. I set up two of the same ports, different names both at the same port, one running TCP and the other UDP, when it worked previously the "both" option did not work correctly. (I used to have a private network that a buddy of mine set up a while back, and I doubt he remembers what to do and I don't know where the manual is to make a new one, searching the internet sends me spam of people asking questions.)
I read somewhere it may have something to do with DHCP server settings conflicting with my IP. My IPv4 address reads 192.168.2.100, and the DHCP settings says the same.
Type: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again.
View 1 Replies View RelatedI am having a NAT issue with my two xboxes. The router is an e1000 v2.1 firmware 2.1.02. One xbox is wired into the router and the other has a wireless adapter. The wireless xbox gets open nat automatically, while the wired one's nat is strict. If i mess with DMZ and turn UPnP off i can get the wired to be open but the wireless one to be strict. Also port forwarding does not seem to work because only one or the other xboxes will get an open NAT. I do have the the correct ports in the port triggering section set to on but that does not seem like it works.
View 5 Replies View RelatedI have always used netgear routers in the past. After a series of issues regarding configurations not working correctly I invested in what appeared to be a semi pro router, the cisco linksys e4200.
I have a centralized server which I use to access a mass of different services such as mail, dns, VPN, FTP, Kerberos, http and many more. While I am not a massive networking ****, this server setup is like my garage project. To access these services externally to my LAN as far as I understand I would need to configure port forwarding for each service to my server. Unfortunately the control panel for the linksys E4200 only offers about 15 custom port fields for forwarding, and some documentation I have read shows that with it's basic install my server could be using up to 60 ports at once.
Is this router just not suitable for this sort of network. If so I will be very disappointed because I have spent a quarter of the price on netgear routers with more control than this.
Region : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version : TL-MR3420_V2_121206
ISP : 3
I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.
Region : Italy
Model : TD-W8961ND
Hardware Version : V3
Firmware Version : 3.0.0 Build 120720 Rel.09287
ISP : alice
A couple of weeks ago I have bought a TD-W8961ND in replacement of my old modem/router (of another brand, to upgrade from Wireless G to N). I tried to replicate in the new router something similar to my old setup, so I programmed Virtual Servers (under the NAT menu) with the following rules: NATRules.jpg in an attempt to:
- grant access from "outside" Internet to my web server
- have a Wakeup-On-LAN from "outside" Internet ..etc.. without success. Please note that:
- I have successfully setup a DDNS server to reach my modem router from outside
- as for WOL, I defined my subnet mask as 255.255.255.128
- I have not set any other rule, nor in NAT, nor in routing or other
- I tried also with firewall disabled
- I do my testing by means of a smartphone with wireless disabled and Internet connection via mobile service provider
- Both the above mentioned functions were working with my old modem/router (and still work on LAN), and I have not changed other things (PC setup etc)
I have a new Polycom Soundpoint IP550 VOIP phone that was not connecting via my old WRT54GS router. I purchased a new router, the E4200, thinking it was just the age of my original router. It also will not allow the VOIP traffic through. I can connect the VOIP phone directly to my CenturyLink modem and it works. But when I connect it back to the router it stops.
I contacted Cisco support and they had me upgrade the firmware to 1.0.02 build 13 May 24, 2011 version. Also adjusted down the MTU to 1364. That still did not work so they told me to take the router back to the store. I have not done that yet as I want to ensure that the router is really broken and not that I am missing a setting. The tech said that I should be able to plug the VOIP phone into the router and make NO additional changes.
I just purchased a new E4200 router. When I try to set it up, , it says that my software (Lion v. 10.7.2) is unsupported. Is there a download that will allow me to use this router?
View 2 Replies View RelatedI have an HP LJ4050 plugged right into one of the open LAN ports on my E4200 with a CAT6 cable. Can this router work as a LAN print server? I can't pull up the IP on a browser window or ping it successfully.The 4050 doesn't have USB capability and I don't want to use the parallel port on my PC unless I have to.If possible, I'd like to have wireless computers on the network be able to print to it as well.
View 5 Replies View Relatedwhy Windows Backup in Windows 7 pro 64 would not backup over the network to a drive I have connected to the 4200s USB port? Everytime I run it I get a Access Denied error at the end, even though data has been transfered. After about 5 hours of searching both here and Microsoft's website, I just get lots of people with the same issue that hasnt been resolved anywhere consistantly.
View 1 Replies View RelatedI have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
View 1 Replies View RelatedI'm looking to purchase the E4200 and use an external HDD with enclose as a NAS (probably just a backup drive), specifically this model. [code]The HDD would be a 1TB Samsung Spinpoint F3.Does this router allow for USB 3 connections or at least fallback to USB 2? The first comment on the external enclose says so otherwise.
View 3 Replies View RelatedModel name: Linksys E4200
Model number: E4200
Firmware version: 2.0.36.126507
Operating system: Windows XP SP 3
Software version: 1.4.12005.2
Connection type (WAN): DHCP
My Canon MX882 multifunction printer is connected to the router via USB cable. The printer works. The scanner does not work.
I have tried both old firmware (2.37) then the Cloud firmware and now back to 2.37 again. the parental controls seems kind of fool proof but anyhow they dont work for me.If I set the internet access as denied at certain times, if the client is already connected when that time occours, it can continue to use internet (until it disconnects and tries to reconnect). Happens almost every time. And the biggest problem is that if I try to block internet access for a device like a cell phone, even though the user can not access the internet through the web browser, apps like Facebook, games etc can still access internet. Kind of useless parental control?!But I have tried to reset, reflash etc.Also I find this router pretty unstable, the only device that works flawless is my iPad (3), the laptops and cell phones at home loses internet connection every one and then, even though it seems like they have good connection to the router. Never been a problem with my earlier routers.
View 9 Replies View RelatedI am finding it impossible to set up port forwarding. No matter what I do I remain completely stealthed when I do a port probe via [URL]... The only way I seem to be able to open a port is if I enable remote management. When I do that, whatever port I specifiy as the remote management port is then fully open. Obviously, I can't leave a port exposed like this and, anyway, I need to open multiple ports for my purposes.
View 9 Replies View RelatedI'm trying to port forward with the Linksys BEFW11S4, I've followed all the instruction from support website. I went to the Application & Gaming then Port Range Forwarding. I changed the settings so I can access this IP remotely. When I try to log into this IP from a different network it wont let me.
View 5 Replies View RelatedI am trying to install and use EchoLink on my pc's and they require port forwarding for 5198-5200 but I'm having trouble with theTo IP Address" as I don't know what # to use. It says I can't use 192.168.1.1 since it's the same as the LAN IP address so what do I use? I am trying to follow the instructions on [URL] If I leave it just as 192.168.1. it won't accept it and if I use any other number, it accepts it but I still can't get through.
View 3 Replies View RelatedMy first issue with this device is when I try to untick NAT to disable it I lose my internet connection. This also disables access to router's address 192.168.1.1 forcing me to reset the device and set it up all over again. Why is this happening? I tried this at least five times with the same result. Second question I have is if the DHCP reservation is the right option if I want to forward ports for certain applications like Vuze? When the DHCP reservation window opens I see all my wireless devices in the list (laptop, phone) but not the main computer which is connected through ethernet port. But that is yet another problem.
I've got a cable modem, connection is set to Automatic DHCP and I all want is to disable all firewalls, NAT and other unnecessary protection that's slowing my internet speed, set up MAC address filtering, port forwarding and close this terrible software so I never have to see it or think about it ever again.
I just bought a WRT120N wireless router, and have run into some strange problems with port forwarding. I have a two router setup, because my ISP have set it up so i can only use my router from them to get my connection, and then i just have that one connected to my WRT120N. So my setup looks like the following:
The problem is that ONLY the three first ports works. I have forwarded them in the exact same manner, give it a name, put in the same external and internal port, and enable the port forwarding, but according ot can you seeme.org, only 4667, 6112, and 4669 can be seen, the rest is not responding. I even tried to enable port 21, which is a default setting in the router, but it will just not work.I have of course tried to reboot both router and PC, upgraded the routers firmware, but no luck.
I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500. I have tried both the single port forwarding and the multi port range forwarding, and neither works. I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.I'm running the latest firmware provided by Linksys/Cisco.
View 1 Replies View RelatedI recently got a e2500 router and set up the port forwarding for my ps3. But then i go to check the ports to see if they are open and they all stay closed.I have no clue whats wrong as I have entered the port forwarding info correctly as I got guideline from portforward.com but still no luck
View 2 Replies View RelatedI'm trying to forward my ports and I've been following a guide from [URL]. It's simple, but it's not working for me. I couldn't find my router on their list, so I'm assuming the worst and that it's not supported for the Port Forwarding. I just went with the normal WRT54G without the version 8 and tried it that way, I didn't get anything out of that either. It keeps telling me that the port isn't open and I can't receive the information packets that they're sending me.
View 3 Replies View RelatedIm going to change my NAT status to "open" on my xbox 360, but I don't have access to the router I think. Its my grandmas internet and im going to be here for 10 days so it could be nice if you could tell me the username and password so i can open the ports?
Model:Cisco EPC3925Vendor:CiscoHardware Revision:1.0 MAC Address:18:59:33:ad:b0:a0Bootloader Revision:2.3.0_R1Current Software Revision:EPC3925-ESIP-16-v302r125532-110504cFirmware Name:epc3925-ESIP-16-v302r125532-110504c.binFirmware Build Time:May 4 17:40:26 2011Cable Modem Status:OperationalWireless Network:Enable