Linksys Wireless Router :: E4200 Wake On Lan Doesn't Work Over Internet
Aug 12, 2011
I'm having a problem with Wake on Lan. (I'll bet you never guessed from the title, eh?). I have an E4200 and I can not get WoL to work over the internet.(I'm assuming it's not actually going out to the internet when I wirelessly wake it using shawn.dynamicservice.com and the subnet, but rather the DDNS name is being resolved through the ARP cache, but I don't know. I'm still learning) Consequently, if the sentence above in parenthesis is correct, I am unable to perform WoL from outside my LAN. What am I missing?
I have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
I have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
I have a Motorola Docis Surfboard model Model SB6120 and can connect to the internet with the ethernet cable directly onto the labtop but if I connect it to the E4200 router the range is there but the internet connection is not. This happened 2 days ago and can't get the router to work.
Im trying to bridge my zyxel eq660r-f1 dsl modem so that i can resolve the nat issue im having in my home network. Only problem is that everytime I bridge the modem and hook my E4200 up, I cannot connect to the internet. If i connect my laptop directly to the modem, I do get internet but not through the router itself.
Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7 Linkysy E4200 V1 Century link DSL modem 660 series
Putting this router back in service, I reset (10 and 30 sec hold) until lights flashed. Unplugged it. Came back and connected to computer. Used default u/n = blank and p/w = admin -- doesn't work, can't get to control screen. Tried various combinations and still won't work. How do I get router to respond?
I have a mac 10.7.4 and an xbox 360 slim. Whenever I try to play online like cod or fifa and someone else is on the computer It is super lagy, Laging. Before when I had a **bleep**y netgear 33 mb it worked perfectly fine. Now this router is has 300 +mb and it stil doesnt work. This router cost me $80 dollars. Before cisco linsys I bought a netgear not the **bleep**ty neatgear but a newer one and it still had the same problem.
I just received a new modem from my ISP acanac, the modem model is NetVito5300.When I connect the modem directly to my computer, I can access the internet, but if I connect through my wireless router, there's no wireless internet access. Wireless router model is CISCO Linksys E2000.I tried to download Cisco Connect Setup Software for PC and followed the step until one point it asked for my wireless username and password and I put them in correctly but it said my router was not successfully set up and failed. I should press the reset button and set the router to factory default mode, but I'm afraid I won't be able to set it up properly after doing so.What should I do to connect my new modem and wireless router properly so I have wireless internet access?
Trying to troubleshoot a Cisco Pix 501. We have a cable modem/router that goes to the Cisco box that then goes to my wife's computer. It's worked flawlessly since we hooked it up, even if we unplug/replug the router. Today, we unplugged the Cisco box itself to hook up a newer one. When the newer one didn't work, we tried to hook up the old one again to no avail. The led indicators seem to show that everything's working properly. We've unplugged and rebooted everything. Nothing works. The network monitor on the computer shows that it detects being connected to a network, but it always says no internet access.
I have a new Polycom Soundpoint IP550 VOIP phone that was not connecting via my old WRT54GS router. I purchased a new router, the E4200, thinking it was just the age of my original router. It also will not allow the VOIP traffic through. I can connect the VOIP phone directly to my CenturyLink modem and it works. But when I connect it back to the router it stops.
I contacted Cisco support and they had me upgrade the firmware to 1.0.02 build 13 May 24, 2011 version. Also adjusted down the MTU to 1364. That still did not work so they told me to take the router back to the store. I have not done that yet as I want to ensure that the router is really broken and not that I am missing a setting. The tech said that I should be able to plug the VOIP phone into the router and make NO additional changes.
I've tried to cascade two Linksys routers, but It hasn't worked for me. The first one (which has cable-modem connection) is the brand new E4200, and the second one is the old WRT54GCv3.[code] However, the WRT54GCv3 doesn't get the IP address from the E4200's DHCP. I've also tried to connect them directly (without the PLC), even specifing an static IP on the second router, but I got the same results.I've to state I don't want to change the first router IP/gateway parameters because I have a web and game home server working with an static IP and I don't want to put it offline temporarily because of readjusting network parameters.
U just bought a new E4200 router to enjoy 5ghz band for the first time.I noticed the range at my house of the 5gh is smaller than 2.4 is that right?one of my pc is having trouble keep connected to the 5ghz signal or the router doenst respond to it, is there a way to improve that signal?
Buy new one Linksys E3200. Two day using and now have such problem. Every 30 minutes WiFi connection disappears for 10-15 sec. Then appear, but you can't connect to WiFi network for next 30 seconds. Update firmware of router to last version, but it doesn't work.
I have just upgraded my E3200 to firmware: 1.0.04 build 1 Apr 10, 2012.The guest network SSID didn't show before in my access point list, but now I can't even change the settings on the router.The options are greyed out.
I just purchased a new E4200 router. When I try to set it up, , it says that my software (Lion v. 10.7.2) is unsupported. Is there a download that will allow me to use this router?
I set up my new E4200 to forward port 7300 to a computer on my LAN. I had this working on my Linksys WRT160N and copied all of the settings so they are identical to those on that router but forwarding does not work. I have tried single port forwarding, multiple port forwarding and even DMZ with the same lack of results.
I have an HP LJ4050 plugged right into one of the open LAN ports on my E4200 with a CAT6 cable. Can this router work as a LAN print server? I can't pull up the IP on a browser window or ping it successfully.The 4050 doesn't have USB capability and I don't want to use the parallel port on my PC unless I have to.If possible, I'd like to have wireless computers on the network be able to print to it as well.
why Windows Backup in Windows 7 pro 64 would not backup over the network to a drive I have connected to the 4200s USB port? Everytime I run it I get a Access Denied error at the end, even though data has been transfered. After about 5 hours of searching both here and Microsoft's website, I just get lots of people with the same issue that hasnt been resolved anywhere consistantly.
I'm looking to purchase the E4200 and use an external HDD with enclose as a NAS (probably just a backup drive), specifically this model. [code]The HDD would be a 1TB Samsung Spinpoint F3.Does this router allow for USB 3 connections or at least fallback to USB 2? The first comment on the external enclose says so otherwise.
Model name: Linksys E4200 Model number: E4200 Firmware version: 2.0.36.126507 Operating system: Windows XP SP 3 Software version: 1.4.12005.2 Connection type (WAN): DHCP
My Canon MX882 multifunction printer is connected to the router via USB cable. The printer works. The scanner does not work.
I have tried both old firmware (2.37) then the Cloud firmware and now back to 2.37 again. the parental controls seems kind of fool proof but anyhow they dont work for me.If I set the internet access as denied at certain times, if the client is already connected when that time occours, it can continue to use internet (until it disconnects and tries to reconnect). Happens almost every time. And the biggest problem is that if I try to block internet access for a device like a cell phone, even though the user can not access the internet through the web browser, apps like Facebook, games etc can still access internet. Kind of useless parental control?!But I have tried to reset, reflash etc.Also I find this router pretty unstable, the only device that works flawless is my iPad (3), the laptops and cell phones at home loses internet connection every one and then, even though it seems like they have good connection to the router. Never been a problem with my earlier routers.
I am setting up a new E4200 modem, and have not been able to use the wired connection. The Windows 7 diagnositic on all three computers tells me "Local Area Connection, doesn't have a valid IP configuration."Model: E4200v1..I am using a new E4200 router, along with a new SE1500 5-port switch and a new SE2800 8-port switch.I am using a wired network that consists of two desktop computers, a laptop computer, a network printer, three Direct TV recorders, two Roku streaming video players, a BluRay player, and an XBox gaming console.Here is what I have done so far.
1- I can bypass the router to establish a direct wired connection to the cable modem. This works to access the internet. It establishes a new wired connection called Network 2. 2- I can access the internet using the wireless connection to the router. It shows a valid IPv4 address. 3- With all cables in place, all the lights are flashing on the router and on the computers. 4- I had changed cables and swapped cable ends. 5- Using the wireless connection, I can access the router home page (192.168.1.1). It shows valid IP addresses.
The problem is that my old Linksys BEFSR81 stopped working, with the same eror message for the LAN connection, "Local Area Connection, doesn't have a valid IP configuration."How often does the WAN port go bad? On both a five-year old BEFSR81, and a brand new E4200?
Type: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again.
I recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface. I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work. I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail. The wireless and everything works as it should, I just can't get back into the router to change any of my settings.
I've been trying to port forward my WRT54G2 router.I've tried to update the Firmware, use another computer or another browser.But it still doesn't work!
I have successfully set up a guest network on my EA4500. Guest laptop associates with guest SSID just fine. Then via IE, it gets prompted for the guest password, which is entered and accepted just fine. At this point guest laptop is on the network.
BUT... at some point the guest laptop will need to reauthenticate (I don't know what the timeout is, but maybe one or two days?). Anyway, it's at this point that IE presents the guest network login page. But now after typing in the password, "enter" or clicking on the button does nothing. It looks like the guest web page doesn't get loaded properly or completely, so the reauthentication can't complete, therefore can't get to the internet. So, while in this state, I've also tried Firefox and Chrome, and same thing, no action when trying to submit the guest password. Tried rebooting guest laptop, and still same problem. Only thing I've found so far that works is to reboot the router. So I'm guessing there's a problem with the guest/web server on the router?? It's a real pain to have to reboot the router every day or two, when I've had other Linksys routers run for months without having to touch them.
I was running CCC 2.1.38 when I first noticed the problem. Since then I've downgraded to Classic 2.0.37, but it seems I still have the same problem. Again, I can connect & authenticate just fine initially, but when reprompted after some period of time, it doesn't work.
I've tried contacting Cisco support, but it looks like I'm at 91 days since purchase and thus outside of my 90-day complimentary support, so they happily provided me with the premium support options just to have the honor of talking with them. Guess I shouldn't have spent so much time trying to figure this out myself.
I'm trying to fix the network at a student housing building and the system is kind of a mess. We bought a new E4200 to replace our old Linksys router which no one knows the admin pw to. We have four switches for 50 connections throughout the four story house and when switching the connections over to the new E4200 all of the wired connections no longer work. Switch back to the old router and presto. How do I need to change the settings with the E4200 to get it to work?
Also, as it's a thick old house the E4200's wireless only covers maybe half of it...I purchased two wireless repeaters to put on the 3rd and 4th floors, are these simple to install with the router?
