Linksys Wireless Router :: New Modem Doesn't Work With E2000?
Nov 7, 2012
I just received a new modem from my ISP acanac, the modem model is NetVito5300.When I connect the modem directly to my computer, I can access the internet, but if I connect through my wireless router, there's no wireless internet access. Wireless router model is CISCO Linksys E2000.I tried to download Cisco Connect Setup Software for PC and followed the step until one point it asked for my wireless username and password and I put them in correctly but it said my router was not successfully set up and failed. I should press the reset button and set the router to factory default mode, but I'm afraid I won't be able to set it up properly after doing so.What should I do to connect my new modem and wireless router properly so I have wireless internet access?
View 6 Replies
ADVERTISEMENT
Mar 11, 2013
I tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
View 7 Replies
View Related
Aug 3, 2011
I've just bought an E2000 and I Cisco Connect doesn't run on OSX-Lion, and I was unable to find it on support downloads. But this is only a comment, my concern is that I'm not able to see on main menu how many DHCP clients are connected nor of course to check their traffic. Other routers usually provide at least DHCP clients
View 4 Replies
View Related
Oct 8, 2011
I'm trying to register my new linksys e2000-ew wireless router but it doesn't show up in the selection pull down menu. When I try the e2500 it says my serial# isn't correct.
View 5 Replies
View Related
Aug 30, 2011
I am using a E2000 connected to a DSL modem via the internet port. My modem is able to connect at gigabit speed but it doesn't seem to be the case with the E2000. All other ports are running at gigabit speed without problem. Is there any parameter that can be modified or is it a router limit?
View 2 Replies
View Related
Dec 25, 2011
So my family has an E2000 setup near the modem in a room that litterally is a DEADZONE, signal bearly gets in or out of this room. I've argued until I was blue in the face that we ned to rewire the internets inlet to the house in to another room that isn't a deadzone and rune a router from there.They IT disadvantaged refused. We have also an E2500 they say hook it up, maybe it will work better (when your in a concrete and mettal room with a router sitting on a shelf surrounded by book and with a corless phone system hooks up and sitting on top of it... its jsut not going to work. is there a way i can take the E2500 and make it an access point for the E2000?
I figure if I can I would take the E2500 and put int in a better location and jsut have it relay the E2000 internet. Because of the IT limited thought process of most of the people living here I'd prefer that they share the same SSID or atleast make for a simple transition for the apes I live with.
View 6 Replies
View Related
Jan 23, 2012
I bought an E2000 router with modem Dlink DSL-320B in PPPoA mode. I have already spent much time for to configure the router with-out any positive feedback . I've selected Automatic configuration with dhcp , static ip 192.168.1.2 and dhcp and modem with 192.168.0.1 and dhcp . If i view the status windows (internet connection) in router i see the right address for gateway and internet Ip , but is not allow to navigate by other PC linked with internal switch of E2000. Do you Know some particluar set-up for PPPoA mode ?
View 5 Replies
View Related
Feb 27, 2012
Using a Linksys E2000 and Linksys WRT54GL (both flashed to most recent firmware), I am trying to set up Network "A" and Network "B" on one modem. I do not want either A or B to be able to see each other for security purposes. Both are secured networks for the wireless connections and have different SSIDs.
After online research, and the inability to find my exact question answered, this is what I did and I'd like to know if I'm missing anything to keep A and B completely separate. Or, if I've done anything that will cause any problems on my network. [code]
I disabled the ability to change settings using wireless connection on both routers.
View 9 Replies
View Related
Jun 10, 2011
I recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
View 2 Replies
View Related
Jun 23, 2010
I've been into the setup page several times over the years but now it won't load. I recently reset it and want to setup security again.
View 6 Replies
View Related
Nov 29, 2012
Putting this router back in service, I reset (10 and 30 sec hold) until lights flashed. Unplugged it. Came back and connected to computer. Used default u/n = blank and p/w = admin -- doesn't work, can't get to control screen. Tried various combinations and still won't work. How do I get router to respond?
View 9 Replies
View Related
Aug 1, 2012
I have a mac 10.7.4 and an xbox 360 slim. Whenever I try to play online like cod or fifa and someone else is on the computer It is super lagy, Laging. Before when I had a **bleep**y netgear 33 mb it worked perfectly fine. Now this router is has 300 +mb and it stil doesnt work. This router cost me $80 dollars. Before cisco linsys I bought a netgear not the **bleep**ty neatgear but a newer one and it still had the same problem.
View 1 Replies
View Related
Oct 17, 2011
I have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
View 1 Replies
View Related
Jan 7, 2013
Trying to troubleshoot a Cisco Pix 501. We have a cable modem/router that goes to the Cisco box that then goes to my wife's computer. It's worked flawlessly since we hooked it up, even if we unplug/replug the router. Today, we unplugged the Cisco box itself to hook up a newer one. When the newer one didn't work, we tried to hook up the old one again to no avail. The led indicators seem to show that everything's working properly. We've unplugged and rebooted everything. Nothing works. The network monitor on the computer shows that it detects being connected to a network, but it always says no internet access.
View 1 Replies
View Related
Aug 12, 2011
I'm having a problem with Wake on Lan. (I'll bet you never guessed from the title, eh?). I have an E4200 and I can not get WoL to work over the internet.(I'm assuming it's not actually going out to the internet when I wirelessly wake it using shawn.dynamicservice.com and the subnet, but rather the DDNS name is being resolved through the ARP cache, but I don't know. I'm still learning) Consequently, if the sentence above in parenthesis is correct, I am unable to perform WoL from outside my LAN. What am I missing?
View 3 Replies
View Related
Aug 19, 2012
Buy new one Linksys E3200. Two day using and now have such problem. Every 30 minutes WiFi connection disappears for 10-15 sec. Then appear, but you can't connect to WiFi network for next 30 seconds. Update firmware of router to last version, but it doesn't work.
View 3 Replies
View Related
Aug 19, 2012
I have just upgraded my E3200 to firmware: 1.0.04 build 1 Apr 10, 2012.The guest network SSID didn't show before in my access point list, but now I can't even change the settings on the router.The options are greyed out.
View 6 Replies
View Related
Mar 15, 2011
Hardware: Modem-Motorola SBV5222 Router-Linksys E2000(Cisco brand name? I didn't buy the router) I use a PC with windows xp with sp 2 and 3 installed.Problem: I can use the internet just fine when I am connected to the router, my pc is connected directly to the router via cat 5 but when I directly connect to the modem I get limited to no connectivity. I'm not using a proxy server and before the router was set up(I live with roommates who set up the wireless network.) I could connect to the modem just fine. I can't repair the connection since it seems to be unable to renew the ip address. I've also tried to manually configure my ip address though I'm sure it wasn't the issue.I've racked my brain to think of a simple solution and it doesn't seem one is apparent and I'm almost sure it's something to do with xp and I'm not so great with software.
View 4 Replies
View Related
May 1, 2013
I have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
View 2 Replies
View Related
Jul 1, 2012
Type: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again.
View 1 Replies
View Related
Jan 10, 2012
I recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface. I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work. I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail. The wireless and everything works as it should, I just can't get back into the router to change any of my settings.
View 4 Replies
View Related
Jan 22, 2012
I've been trying to port forward my WRT54G2 router.I've tried to update the Firmware, use another computer or another browser.But it still doesn't work!
View 1 Replies
View Related
Sep 15, 2012
I have successfully set up a guest network on my EA4500. Guest laptop associates with guest SSID just fine. Then via IE, it gets prompted for the guest password, which is entered and accepted just fine. At this point guest laptop is on the network.
BUT... at some point the guest laptop will need to reauthenticate (I don't know what the timeout is, but maybe one or two days?). Anyway, it's at this point that IE presents the guest network login page. But now after typing in the password, "enter" or clicking on the button does nothing. It looks like the guest web page doesn't get loaded properly or completely, so the reauthentication can't complete, therefore can't get to the internet. So, while in this state, I've also tried Firefox and Chrome, and same thing, no action when trying to submit the guest password. Tried rebooting guest laptop, and still same problem. Only thing I've found so far that works is to reboot the router. So I'm guessing there's a problem with the guest/web server on the router?? It's a real pain to have to reboot the router every day or two, when I've had other Linksys routers run for months without having to touch them.
I was running CCC 2.1.38 when I first noticed the problem. Since then I've downgraded to Classic 2.0.37, but it seems I still have the same problem. Again, I can connect & authenticate just fine initially, but when reprompted after some period of time, it doesn't work.
I've tried contacting Cisco support, but it looks like I'm at 91 days since purchase and thus outside of my 90-day complimentary support, so they happily provided me with the premium support options just to have the honor of talking with them. Guess I shouldn't have spent so much time trying to figure this out myself.
View 9 Replies
View Related
Oct 5, 2012
Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
View 9 Replies
View Related
Aug 9, 2011
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies
View Related
Feb 23, 2013
Blank user name and admin in password doesn't work. How to reset these ?
View 1 Replies
View Related
Sep 26, 2012
Attempting to get EA6500 working with TWC Motorola Surfboard SBV5220 modem, which has been working just fine for the last 2 years with a Linksys E3000 router. DHCP client in the EA6500 either doesn't ask for an IP address from the cable modem or the modem just isn't supplying one. With the E3000, you could see the IP address assigned by the cable modem and the primary and secondary DNS server addresses provided, and if the DHCP request didn't work, these addresses would be all zeroes. But, with the EA6500, I can't find an equivalent screen that shows these assignments, or zeroes when the DHCP request fails.
View 1 Replies
View Related
Oct 29, 2012
I just got an used Pc from auction today.I installed it with Xp Pro. I am trying to connect it to my wire modem but it doesn't work.
View 4 Replies
View Related
Feb 26, 2011
I have a Netgear WRG614 and a Westell 610015 Modem. I need Port Forwarding. I have tried setting up a static IP then Port Forwarding but it doesn't work. I have tried port forwarding from the modem but it doesn't work. I wanna forward ports "80, 9958, and 5816". The reason is because I am gonna host a game server on my computer.
View 14 Replies
View Related
Jul 18, 2011
Comcast sent out a new modem a few days ago. The reason for this was our internet had gone out for a while, they came in and said our modem was fried. I have internet access by directly wiring from the modem to my computer.My router doesn't work anymore. I have a local network, but no internet access. I'm using a Linksys WRT54G, and I don't really know what to do.As far as I remember, setting everything to defaults and factory settings was how I set up my router in the first place and it just worked.
View 11 Replies
View Related
Nov 21, 2012
Continued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
View 1 Replies
View Related
Dec 30, 2011
I got a brand new wireless router and made it the first in line with my cable modem. This is necessary because I want to take advantage of all the features in the new router. I put the RTP300 behind the first router and switched off DHCP and connected the internet port into one of the 4 regular ports on the back (typical configuration for a pass through router).So everything works perfectly for any computer attached to the router (they can access the internet etc). The only problem I have is the VOIP doesn't work. If I pick up my phone it says this device is not registered to a phone number.
View 1 Replies
View Related
Jan 29, 2013
The latest driver is version 3.2.7 for Windows 7. I am still on the 3.0.2.0 driver which works fine for me. I just wanted to note that the 3.2.7 driver obtained from Windows Update doesn't work well, drops connections and takes longer to establish a connection. I've tried to update twice and each time I go back to the older driver.Can someone at Linksys examine the performance of this driver?
View 9 Replies
View Related
