Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
Region : Others
Model : TL-MR3040
Firmware Version: 3.14.4 Build 121017 Rel.62268n
I have purchased TL-MR3040 especial for share my 3G account . I have connect it by ethernet port and made setups and it is in 3g/4g only mode. In system checks my modem indicated as " Identified" the modem is a Huawei E160E . My notebook and tablet connects by wireless connection to TL-MR3040 but the router does not dial ISP number *99# . The led on usb modem continues flashing. the 3G modem works perfectly with my notebook and tablet and I use the same parameters for TL-MR3040 with tablet. But most of the parameters don't exist on setup pages of TL-MR3040 . [code]
we have tried updating the firmware, restarting the modem, etc.We are looking to connect our 2 TB WD My Book to our E4200 to share amongst the network to various gaming systems and computers , When we go to storage it says "USB Device is not Supported"
View 1 Replies View RelatedE4200 does fail functionality on 2 area's:
- 1) Media Streaming Server
- 2) NAS supporting modern USB devices, which register with multiple personalities/devices in one physical USB device.
1) Is already known by Cisco and hopefully the choose to fix it properly
2) Must be known now. Multiple users are reporting this lack of support.
NAS functionality of E4200 does not work/ gives problems with:
- Toshiba StorE Alu 2S USB 3.0, 1 TB disk. PN: PA4239E-1HJ0
- Iomega eGo 1 TB USB 3.0, (black casing) , PN 31924500, RPHD-UG3
Both drives report themself with 2 devices under Windows 7: 1x USB storage decive + 1x CD readonly device?
I have a WRT54GS V7 that I have been running for a few years now with no problems until today.My wife used the internet from her laptop through the day but this evening after she moved to the bedroom and booted up the laptop, she found there was no internet connection. I tried what I know in cases like these, unplugging the router or modem for brief periods of time to try and get things going again but to no avail. So I tried using the Easylink Advisor which basically suggested the same process.
At this point, my internet connection is coming in from the cable just fine. I have access on the desktop which is wired and works with no problems. The modem and router lights are both signaling that everything is fine but no wireless internet coming from the router.
Using the desktop I tried looking for some solutions and tried resetting the router. I ultimately called customer support but being out of warranty they wanted too much although she suggested that I needed to reconfigure the router since I had reset it. I followed the online instructions for reconfiguring but still have gotten nowhere.
I usually connect my PS3 to a switch which then goes to the BuT Home Hub and it works fine. However, I want to connect the PS3 directly to my Hub but when I plug it in to the Hub, it doesn't connect to the internet at all. Is there something I have to configure in order to get it to work?It is a PS3 160 GB Slim with Firmware 4.0.
View 2 Replies View RelatedI cannot use my AE1000 device for more than twenty minutes connected on windows ultimate 64bit.AE1000 doesn't startup with Windows 7 64bit.The led light still turn on when I turned off my PC.
View 3 Replies View RelatedI purchased a new router and it doesn't have a security key. I can't connect my blue ray or roku.
View 1 Replies View RelatedI have a Speedstream 4300 modem in bridge mode and a linksys WRT54G2 router set to PPPoE like I was instructed. On the status page of my router underneath the PPPoE setting it has IP, Subnet Mask, and Gateway all set to 0. The only advice I was able to obrain from my ISP was to powercycle the router and modem, which I did and no change.
View 1 Replies View RelatedI have a Motorola Docis Surfboard model Model SB6120 and can connect to the internet with the ethernet cable directly onto the labtop but if I connect it to the E4200 router the range is there but the internet connection is not. This happened 2 days ago and can't get the router to work.
View 4 Replies View RelatedI can't connect with putty to E4200.I tried different ways - telnet, ssh, etc.
View 1 Replies View RelatedI have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
View 1 Replies View RelatedI'm having a problem with Wake on Lan. (I'll bet you never guessed from the title, eh?). I have an E4200 and I can not get WoL to work over the internet.(I'm assuming it's not actually going out to the internet when I wirelessly wake it using shawn.dynamicservice.com and the subnet, but rather the DDNS name is being resolved through the ARP cache, but I don't know. I'm still learning) Consequently, if the sentence above in parenthesis is correct, I am unable to perform WoL from outside my LAN. What am I missing?
View 3 Replies View RelatedIm trying to bridge my zyxel eq660r-f1 dsl modem so that i can resolve the nat issue im having in my home network. Only problem is that everytime I bridge the modem and hook my E4200 up, I cannot connect to the internet. If i connect my laptop directly to the modem, I do get internet but not through the router itself.
View 8 Replies View RelatedI've tried to cascade two Linksys routers, but It hasn't worked for me. The first one (which has cable-modem connection) is the brand new E4200, and the second one is the old WRT54GCv3.[code] However, the WRT54GCv3 doesn't get the IP address from the E4200's DHCP. I've also tried to connect them directly (without the PLC), even specifing an static IP on the second router, but I got the same results.I've to state I don't want to change the first router IP/gateway parameters because I have a web and game home server working with an static IP and I don't want to put it offline temporarily because of readjusting network parameters.
View 9 Replies View RelatedI have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
View 2 Replies View RelatedU just bought a new E4200 router to enjoy 5ghz band for the first time.I noticed the range at my house of the 5gh is smaller than 2.4 is that right?one of my pc is having trouble keep connected to the 5ghz signal or the router doenst respond to it, is there a way to improve that signal?
View 2 Replies View RelatedJust swapped to an ActionTec modem with a very nice GUI on it. I would like to be able to access the GUI from any computer on my network. The modem is in bridge mode, with it's DHCP server turned off. My e4200v2 has a base address of 192.168.1.1, is running DHCP and NAT is enabled. The modem is attached to the WAN port.I would like to enter a static route to get to the router, but I keep getting "invalid static route".
View 2 Replies View RelatedWe have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies View RelatedI am setting up a new E4200 modem, and have not been able to use the wired connection. The Windows 7 diagnositic on all three computers tells me "Local Area Connection, doesn't have a valid IP configuration."Model: E4200v1..I am using a new E4200 router, along with a new SE1500 5-port switch and a new SE2800 8-port switch.I am using a wired network that consists of two desktop computers, a laptop computer, a network printer, three Direct TV recorders, two Roku streaming video players, a BluRay player, and an XBox gaming console.Here is what I have done so far.
1- I can bypass the router to establish a direct wired connection to the cable modem. This works to access the internet. It establishes a new wired connection called Network 2.
2- I can access the internet using the wireless connection to the router. It shows a valid IPv4 address.
3- With all cables in place, all the lights are flashing on the router and on the computers.
4- I had changed cables and swapped cable ends.
5- Using the wireless connection, I can access the router home page (192.168.1.1). It shows valid IP addresses.
The problem is that my old Linksys BEFSR81 stopped working, with the same eror message for the LAN connection, "Local Area Connection, doesn't have a valid IP configuration."How often does the WAN port go bad? On both a five-year old BEFSR81, and a brand new E4200?
I just received a new modem from my ISP acanac, the modem model is NetVito5300.When I connect the modem directly to my computer, I can access the internet, but if I connect through my wireless router, there's no wireless internet access. Wireless router model is CISCO Linksys E2000.I tried to download Cisco Connect Setup Software for PC and followed the step until one point it asked for my wireless username and password and I put them in correctly but it said my router was not successfully set up and failed. I should press the reset button and set the router to factory default mode, but I'm afraid I won't be able to set it up properly after doing so.What should I do to connect my new modem and wireless router properly so I have wireless internet access?
View 6 Replies View RelatedOne of the many things that I liked about the e4200 over my olg 54GL was the fact that I could reboot it remotely. However, I've recently had a few problems that only a full power down would fix. In addition, I've noticed that the DCHP client table doesn't reset when I do a soft reboot. Is this intentional? Is the soft reboot not really a full reboot? Can it be made a real reboot?
View 7 Replies View RelatedI recently installed some wireless IP cameras and when attempting to re-install a camera I went into the DHCP Client table to verify which IP a camera was using to set it up, but I could not...and still cannot see any of my cameras in the table even though I can access three of them directly through the IE web browser. I initially power cycled both the E4200 router and Motorola cable modem, and then later just the wireless router...but I still do not see the devices connected. I currently have 2.0.37 firmware even though I was told by Cisco support that there was a later version available, just before being informed that I do not have support available and could purchase it. I attempted to locate a newer version, but the online upgrade portion of the Cisco Connect software searched the net and then states that I have the latest version available. I also opened a Firefox browser to see if maybe my browser was causing issues, but the same limited table appears without all entries available. I even opened the Cisco Connect software on another laptop with the same limited results. Other than a factory reset, get me E4200 dual band wireless router to show all attached devices through the DHCP Client table as it previously did approximately two weeks ago?
View 2 Replies View RelatedAttempting to get EA6500 working with TWC Motorola Surfboard SBV5220 modem, which has been working just fine for the last 2 years with a Linksys E3000 router. DHCP client in the EA6500 either doesn't ask for an IP address from the cable modem or the modem just isn't supplying one. With the E3000, you could see the IP address assigned by the cable modem and the primary and secondary DNS server addresses provided, and if the DHCP request didn't work, these addresses would be all zeroes. But, with the EA6500, I can't find an equivalent screen that shows these assignments, or zeroes when the DHCP request fails.
View 1 Replies View RelatedOnce in a while, I lose Internet connection and at the same time cannot reach my Siemens Speetstream 4100b DSL modem's setup page 192.168.0.1 ; it happened again this morning (from both wired and wirelessy connected computers). When I go to the router's setup page 192.168.1.1 , it would usually in that situation show that the router has not acquired the Internet IP Address; I power-recycle (a few times) both modem and router and eventually the router reports that it has acquired the Internet IP Address, but there is still no Internet, and the DSL modem's setup page 192.168.0.1 is unreacheable.The situation usually self-resolves only in an hour or so after the time the router has acquired the Internet IP Address: Internet starts working, and the DSL modem's setup page 192.168.0.1 becomes reacheable.
View 2 Replies View RelatedMy internet modem won't read my E4200 router. How do you reconfigure the settings?
View 2 Replies View RelatedI have an E4200 with a USB hard drive connected to its USB port. I want to use the E4200 media server to stream divx and other video files on my Sharp Aquos HDTVs.I have an LC-70LE732U and a LC-52LE832U wired to my network. Both of them seem to discover and successfully connect to my media server however only MP3s and certain MPG files are detected. None of the AVI files show up.I have upgraded my E4200 firmware to 1.0.03 hoping that would fix the problem but it didn't. I don't want to run a Windows based media server as I don't have a computer that I can leave on all the time.
View 3 Replies View Relatedif it is possible to access a modem setup page with a E4200 router? My router is on 192.168.254.200 and modem(WAG-200G) is on 192.168.254.100, ethernet cable is on internet port on the e4200 and on port1 on the modem. Modem is set is bridge and I set up a ppoe and dhcp on router. Everything is ok, except that i can not access modem setup page to see adsl conection speed and settings.
View 1 Replies View RelatedI have a e4200 router, And a 660 series modem, I'm trying to portforward for a game called minecraft, I cannot seem to get the ports to open, I've called Century link they told me to put my modem in to bridge mode, So I did they said my IP should be public not private now, It is still private
View 6 Replies View RelatedI reset my WAP54g v3.05 to factory default to allow an older computer access to my network.
Now I've reinstalled it for better security using my newer laptop: no SSID broadcast and encryption set for WPA2-personal. However, when I enable Mac filtering and permit my newer laptop, the WAP54g does not recognize it.
Disable Mac filtering and my laptop is back on the network.
I have a d-link dsl modem that reports it's getting the full 6 meg download speed from AT&T. I put the dsl modem in bridge mode so the E4200 will do the logon to AT&T with my credentials. If i do a speed check using CNET internet speed test, from both a desktop (wired 1gb card) and any laptop in the house (all draft n 2.4 or 5.0), it ranges anywhere from 3 meg to 4.3 meg. I have 6 cat-e ethernet cords everywhere. I do have 2 switches but have tried to unplug those to see if any difference
View 1 Replies View RelatedMy computer suddenly doesnt recognize my router.it recognizes othrer routers, and my other PC's are recognizing the router.the router is located very close to the PC, and no other electronic devices located near by.
View 2 Replies View RelatedMy Dell destop with Windows 7 all of a sudden doesn't seem to recognize my router, yet my laptop works fine (which I'm using now). After reading other posts, I reset the router with no results, used a new cable from the Belkin to the computer, changed ports, checked connections, restarted; nothing. When I do an ipconfig, a small window pops open and goes off before I can make anything out. I undestand Belkin's IP address is 192.168.2.1 and I'm showing that my IPv4DHCP Server is that, as is my DNS server. The IPv4WINS server shows nothing.
View 9 Replies View Related