we have tried updating the firmware, restarting the modem, etc.We are looking to connect our 2 TB WD My Book to our E4200 to share amongst the network to various gaming systems and computers , When we go to storage it says "USB Device is not Supported"
View 1 Replies
I attached WD My Book Mirror 2TB to E4200 with firmware 1.0.01 but it was very UNreliable. It would give I/O errors when I tried to access the harddisk. So I upgraded to firmware 1.0.02. Now E4200 doesn't recognize my hard disk at all. Yes, my hard disk is in the list of tested devices using NTFS.I contacted support but no luck.
I also have bad range with this router where I am only about 20ft from the router (2 walls in between) but I get about 3 bars out of 5 on my Windows 7. Could it be because I purchased a refurbished product directly from Cisco?
E4200 does fail functionality on 2 area's:
- 1) Media Streaming Server
- 2) NAS supporting modern USB devices, which register with multiple personalities/devices in one physical USB device.
1) Is already known by Cisco and hopefully the choose to fix it properly
2) Must be known now. Multiple users are reporting this lack of support.
NAS functionality of E4200 does not work/ gives problems with:
- Toshiba StorE Alu 2S USB 3.0, 1 TB disk. PN: PA4239E-1HJ0
- Iomega eGo 1 TB USB 3.0, (black casing) , PN 31924500, RPHD-UG3
Both drives report themself with 2 devices under Windows 7: 1x USB storage decive + 1x CD readonly device?
Ok this is the send router this has happened to but anyway after a power blink the router no longer recognizes that i have a modem connected to it no matter how many times I reboot both of them it can't recognize that i have a modem connected i know it is not the modem because i'm using it to type this right now directly connected to my desktop
I have windows 7
Linkysy E4200 V1
Century link DSL modem 660 series
I have been trying to resolve what I think is an issue with DNLP or broadcast data getting to computers connected to my E3200. I have been wiresharking my network, trying different configuration, and scouring the web looking for an answer. My network is setup as shown below. The E3200 is on the same subnet and wired to the switch using the LAN port.DHCP is turned off. UPnP is enabled. DHCP is provided by the WRT54GL and turned off on the E3200.
WesternDigital has a program called "WD QuickView" and another called "WD Smartware" which together provide feedback about the drive status and real time backup capability (I prefer not to argue the +/- of these programs if folks don't mind <grin>). I have two computers on the wired LAN at the 16 port switch on which these programs work just fine. I get feedback about the drive status and backups occur. I also have two computers on the wireless LAN through the E3200 which DO NOT get feedback about drive status and appear not to detect the drive through the software. I CAN however access the drive by mapping it on Windows explorer for example.
With wireshark I do see chatter between the NAS and the E3200 (TCP traffic which I am not sure about...dpkeyserv stuff). I see broadcasts from the NAS to 239.255.255.250 often followed by talk between one of the wired computers and the NAS (which I am thinking is the comms for the WD...not sure though). I do not see chatter between wireless connected computers and the NAS (except for SMB or transferring files). It seems that the E3200 is not forwarding broadcasts to the computers connected to it even though it is connects as a switch.
recently my internet got disconnected, they reconnected my internet configured my modem when i tried to connect my router ,it would connect to my comp but it said there was no internet. I reset it to factory settings via ip address and then threw the button on the router when i installed software it keeps saying that the router cannot recognize the internet and i should contact my internet provider, but my internet is working when i connect it to the comp directly?
View 4 Replies View RelatedI had a Sony 8gb usb drive plugged in and was working great with my smart tv and computer..... over last weekend i unplugged the drive and had to format it to my xbox moved what i need to and hen i formatted it back to ntfs the router wont recognize the usb drive. during this i also was facing this bad gateway error 502...i downgraded my router and now using the classic but i still get a non recognizable device error.
View 1 Replies View Related1TB harddisk partitioned into 2, an HFS+ and an exFAT. Could the exFAT partition be the reason? But I do have an HFS+ partition and it's the 1st partition on this disk.
View 1 Replies View RelatedI cannot get my Toshiba Thrive to recognize my router (wrt-1209) or the other way around. I am able to get on a neighbors non-secure network immediately. No problem with the other wi-fi connected computers on my network.
View 1 Replies View RelatedModel E1000
I wrote down the password of my wireless router on installing it. However, each time I want to add a new device to the router, the password that I wrote down does not prompt the router to recognize the new device or equipment. How do I go back into my computer and retrieve the password to my router if I did copy it down wrongly? how to retrieve the password.
I bought a Wireless-N Home Router MODEL WRT120N so that I could use my new Kindle Fire online, since I could never catch an open wi-fi signal in my house. Router IS correctly installed and working fine.....but when I go to use my Kindle, I see it on the list, click on it, enter my password.......and it tells my my password must be incorrect. I KNOW it is correct! I even went and CHANGED the password just in case!
My Kindle keeps giving the message "Unable to connect to the selected Access Point. Please check the password you have provided."
I have a WRT54GS V7 that I have been running for a few years now with no problems until today.My wife used the internet from her laptop through the day but this evening after she moved to the bedroom and booted up the laptop, she found there was no internet connection. I tried what I know in cases like these, unplugging the router or modem for brief periods of time to try and get things going again but to no avail. So I tried using the Easylink Advisor which basically suggested the same process.
At this point, my internet connection is coming in from the cable just fine. I have access on the desktop which is wired and works with no problems. The modem and router lights are both signaling that everything is fine but no wireless internet coming from the router.
Using the desktop I tried looking for some solutions and tried resetting the router. I ultimately called customer support but being out of warranty they wanted too much although she suggested that I needed to reconfigure the router since I had reset it. I followed the online instructions for reconfiguring but still have gotten nowhere.
I am unable to get my E2000 router to recognize my Ipad2 when trying to connect.
View 2 Replies View RelatedWhenever I try to set up a security code for any of the settings (WEP/WPA etc), as soon as I hit save my computer does not recognize it and I get kicked off the internet and have to restart my router. I have the Linksys model number WRT160N V3
View 2 Replies View RelatedI have Linksys E3000 Router and it is connected to 7 Devices at this moment via DHCP. I have got New NAS Enclousre (8th Device) which has got Lan port . I have connected Box to One free Port on E3000 Router. I see DHCP Reservation from 192.168.0.1 assging one IP to My NAS Enclosure Box i.e 192.168.0.13 But when i ping that box . It's not pingable. When i try to browse that NAS Enclosure's setup web page - it's not opening. I can access that box setup page if i connect direct 1:1 Lan cable over private network (169.254.XXX). It means web server is runing on box. I am clueless. E3000 is assigning IP to NAS Enclosure but can't Browse or Ping. I tried to Assign Manual IP address to NAS enclusure and reconnect to router. Still I can't ping or browse.
#arp -a show that box has IP. (Output from MAC os) .
? (192.168.0.13) at (incomplete) on en0 ifscope [ethernet]
Ping test from Router Page.
PING 192.162.0.13 (192.162.0.13): 32 data bytes
40 bytes from 192.162.0.13: icmp_seq=0 ttl=46 time=286.6 ms
40 bytes from 192.162.0.13: icmp_seq=1 ttl=46 time=290.2 ms
[code]....
Set up our E3000 following the set-up guide. However, wireless devices (laptop, iPhone) recognize the network, but cannot connect. There's no prompt for a password or anything.
View 6 Replies View RelatedI'm trying to get my wife's new 'All Fine 7" netbook Windows' connected via wireless connection. I had a muted attempt at it but so did my daughter and her boyfriend. I've got as far as it saying 'connected' but as soon as it does I get a message; Error from RasDial. I think I have created some conflicts perhaps! In the control panel I have done the following:'Internet options' under 'Connection' I've highlighted 'USB 'Network & Dial-up connections I have a choice of 'My connection' 'Main Computer' 'RT28701' & 'ENC28J601' The connection I have so far seems to be using the RT28701.My other option to 'USB is to select 'Desktop @ 19200' but that didn't seem to work either.
View 9 Replies View RelatedIt says I'm connected, but when I try to get online, it says I'm on the local intranet and "THIS PAGE CANNOT BE DISPLAYED". How can I get it to the internet instead of local intranet?
View 3 Replies View RelatedI have a Speedstream 4300 modem in bridge mode and a linksys WRT54G2 router set to PPPoE like I was instructed. On the status page of my router underneath the PPPoE setting it has IP, Subnet Mask, and Gateway all set to 0. The only advice I was able to obrain from my ISP was to powercycle the router and modem, which I did and no change.
View 1 Replies View RelatedAfter reinstalling Vista, Vista does not recognize my wireless network. I know that the wireless network is working because my i-Touch and my blue-ray (internet streaming) still are working with the Cisco/Linksys E2000. I made sure that the wireless switch on my Gateway laptop was in the on position. The wireless hardware does not show up in the hardware control panel. Is this a driver issue or a hardware issue? It does not seem that it would be a hardware problem.
My Gateway is still under warranty thru Best Buy. If it's a hardware problem, it's covered but if it's a software problem(I take it that a driver would be software), they want $100 to fix. This is what brings me to a second question, if it's a driver issue, should I just upgrade to Window 7? Does Window 7 have build in drivers for wireless hardware?
I just bought a Wireless-N PCI adapter (WMP600N) and followed the instructions given by the CD. I installed the card into an empty slot and ran the CD to install the drivers, but error message 221 keep appearing to tell me that the computer can't see the adapter.
My computer runs on Win 7, 32-bit so I have downloaded the latest drivers for Win 7 from your website. Now I want to manually update my adapter to the Win 7-driver, but I don't know how. The adapter won't even show up in the device manager.
I have a recurring issue with my e4200v1. My wired and wireless connections work fine, but I can't get to the administration website. I have https only set up, and after I get thru the 'certificate error' screen, I get an error that says web page is unavailable. Firfefox tells me that the connection was lost - error 101.I have tried wired and wireless, multiple computers, multiple browsers. I even turned the firewall off on one computer (or I think I did anyway).The only way I know how to fix it is by completely resetting then setting up the router all over again.
View 2 Replies View RelatedUpgraded from WRT610N to E4200. Since upgrading to latest firmware the wan just disappears both 5 and 2.5 Ghz bands. Happened with older firmware but not as often. Using it in briged mode. When this happens I can't even get to the management page with a lan connected pc. Have to do a hard reboot to get it to respond again. This is unacceptable for a router at this price point.
View 2 Replies View RelatedI cannot use my AE1000 device for more than twenty minutes connected on windows ultimate 64bit.AE1000 doesn't startup with Windows 7 64bit.The led light still turn on when I turned off my PC.
View 3 Replies View RelatedI am connecting the E4200 to a Sonicwall TZ100. I want the TZ100 to assign IP addresses to devices that connect to the LAN via the E4200.
How do I have the E4200 act as a WAP only or not assign IP addresses and push that responsibility to the TZ100?
I'd still want the E4200 to have a SID key for LAN access security.
I have a 6 month old Cisco e-4200 router that is updated to the latest firmware, connected to a Motorola surfboard modem on Sudden-link in Midland, TX.
I previously used this exact same setup on Cox Cable in Wichita, KS with no problems. Upon setting it up down here I cannot get the router to pickup an IP address. I have Power-cycled everything multiple times, did a complete reset and re-installation of the router software and still no luck. The Sudden-link techs have no idea what is wrong. They said that the modems signal is strong and everything should be working.
Actually I did get it to work once for a couple of days, however when redoing the surround sound system I had to unhook the cable line and it quit working and I haven't gotten it to work again since. I have tried unhooking everything. Turning it all off. Waiting for 5+minutes, and then reconnecting in order: First the modem, then an ethernet cable to the computer which will usually work. But as soon as I unplug the cable from the computer and plug it into the router it stops working.
I bought Linksys E4200, at a time that is the TOP of the line Cisco routers for Home use.I noticed a serious usage issue with it, I could not identify which are the wifi devices connected to choose for access restriction or parental controls, as the dialog box state only as "Network device", and software control by Linksys does not have any provision to use MAC ID or any other option "except " looking at the dialog box as "Network device".
View 4 Replies View RelatedHow to connect the e4200 to a mac via afp? Trying to mount the network drive so the mac see it and can use for time machine backup.
View 3 Replies View RelatedTrying to update it to the new smart Wifi but getting this error "Incorrect Image File".Yes Ive tried redownloading yes ive tried different browers and yes to unziping the file! and Yes Im downloading the correct version I even tried version 1 for the heck of it and still nothing.
View 3 Replies View RelatedI just received by replacement e4200 v1. I updated the firmware to 1.0.03 build 14 and am up and running just fine. The specs say e4200 should be 300+450Mbps. I am using a software "inSSider 2.0" to view my wireless setup. I get 144(N) at 2.4GHz and 450(N) at 5.2GHz. Please note these are max bit rates and not connect speed or throughput rate. The "inSSider" software gives me the following:
2.4GHz - 1/2/5.5/6/7/9/11/12/14/18/22/124/28/29/36/43/44/48/54/58/65/72/86/116/130/144
5.2GHz - 6/9/12/15/18/24/30/36/45/48/54/60/90/120/135/150/180/240/270/300/360/405/450
I get this information by hovering on the max bit rate field on the row displaying my SSID. So is it correct to say that my e4200 is not designed to reach 300Mbps at 2.4GHz. There is an earlier discussion thread about connection maxing out 144. Please note I am not talking about connect speed or thru-put speed. Max design bit rates of dual band router labeled e4200.
Just got a e4200. However I also have a cisco av power line adapter which worked fine. However when connecting to the 4200 it doesn't recognize the Internet. Have rebooted, reset switched ports etc. But it still doesn't work. It sees the network but not the Internet. Have tried everything ikon but no luck. Cannot connect my directive to the Internet. If I can't get it to work will have to run a 50 foot cable.
View 5 Replies View RelatedFirmware 1.0.00 on my E4200 Hardware v1.0 provided a functioning 6to4 tunnel through Comcast's 6to4 facility. Windows and Linux clients on my local network discovered IPv6 addresses and were able to use them successfully.Unfortunately, after the upgrade to 1.0.03 this functionality was gone. I missed reading the ChangeLog, which said that the automatic tunneling feature was removed in 1.0.01. The now provided IPv6 functionality works much less well. First, automatic configuration (discovery of the 6to4 via IPv4 anycast) no longer works with Comcast's gateway. If I configure the tunnel manually, by specifying a 2002/16 prefix, I regain IPv6 connectivity, but only for Linux clients on my local network.
Windows 7 clients suffer from the problem that because the E4200 hands out ULA addresses, they end up preferring those ULA addresses when making global IPv6 connections in the IP 'source' field, which of course does not work. It's like putting your company mailbox code as the return address on a letter you send via US Mail. Other home routers, such as the AVM Fritz! (url,...) suffer from the same problem. However, they provide an option to turn off ULA at the router.Is it possible to turn off ULA for the E4200?
I have a E4200 router v.01 and when i updated the latest firmware (due to security exploit) it seems that whenever i acess the router settings (192.168.1.1) it doesn't ask me nor to input the admin and the password anymore, using wifi or wired.. I want the usual proccess whenever i go to 192.168.1.1 it will ask me to input my admin and password to change my router settings..
View 4 Replies View Related
