Linksys Wired Router :: RTP300 - VIOP Doesn't Work / Device Not Registered
Dec 30, 2011
I got a brand new wireless router and made it the first in line with my cable modem. This is necessary because I want to take advantage of all the features in the new router. I put the RTP300 behind the first router and switched off DHCP and connected the internet port into one of the 4 regular ports on the back (typical configuration for a pass through router).So everything works perfectly for any computer attached to the router (they can access the internet etc). The only problem I have is the VOIP doesn't work. If I pick up my phone it says this device is not registered to a phone number.
View 1 Replies
ADVERTISEMENT
Feb 22, 2012
I have a situation where a legacy and vestigial Linksys RTP300 that's unconnected to any phones but only to the LAN seems to screw up call transfers between Vonage numbers on phones attached to a single Vonage V-Portal that's also on the same LAN. Inbound and outbound calls are unaffected. Removing the Linksys RTP300 seems to fix the issue.why this would be happening considering the RTP300 isn't connected whatsoever to any phones?
And why only call transfers are affected (attempts to transfer calls just sends calls to voicemail even if the other line isn't off-hook or otherwise in use). The network is flat where the Vonage V-Portal, the Linksys RTP300 and a single small 8-port switch are directly attached to the five built-in switch ports of a firewall router, with the WAN port of the firewall router attached to a T1 CSU/DSU.
View 1 Replies
View Related
Apr 23, 2013
I recently bought a rtp300 and its on the 3.1.24 fw version I have been looking everywhere and i have not found any answer to my problem.It doesnt seem that you can change the pppoe settings (vpi,vci, encapsulation or PPP authentication ) anywhere. Should i return it If i apply the 5.01.04 i could those settings?
View 2 Replies
View Related
Nov 21, 2012
Continued from [URL] which appears to have been closed by a moderator with a reference to Cisco small business website, but the registration there doesn't work, all buttons are inactive etc.
I just need to know what to do with this RV042. I have two modems, a cable and an ADSL. Both are configure correctly, in bridge mode. Both work fine when connected to WAN1, but when connected to WAN2 they never go online (dont' get IP address). The connect lights are on but they never go online.
Firmware Version: 1.3.13.02-tm
View 1 Replies
View Related
Nov 30, 2011
My BEFSR81 is my primary router and has DHCP turned on. The router's DHCP range is set to accommodate 12 devices. I have three computers wired to it and their Host names (as specified in the set-up of each computer) show up in the router's DHCP device table. I also have two printers (one old Brother HL5250DN laser printer and one new HP Photosmart Premier C410a inkjet printer) connected and there are blanks where the Host name should go. I would like to be able to tell which printer is which when I am looking at the DHCP device table. How can I get a names associated with each printer's IP address in the router's DHCP device table? (The real problem is that the router seems to have both printers at the same IP address (192.168.1.100) and if I can get one of them to change I'd like to know which one it was!)
View 1 Replies
View Related
Mar 11, 2013
I tried restarting the router and the computer, but to no avail. I've also tried with another ethernet cable and tried several ports, but that did not work, either. What is interesting is that other computers in the household connect to the router via wire without problems. I suppose that means something's wrong with my computer, however, I do not know what. I have a netgear router which says "N300 Wireless ADSL2+ Modem Router DGN2200v3" on the back. My computer has Windows 7 Home Premium installed. I'm using a DSL connection, and Avast! antivirus.
View 7 Replies
View Related
Mar 28, 2013
I installed Windows 8 on my Dell laptop and my bluetooth device doesn't work properly. When Windows 7 was installed and my laptop and my Samsung Galaxy S3 were paired I could play songs from my phone on my computer. But now it is not possible on Windows 8.
View 1 Replies
View Related
Nov 16, 2011
Cisco LMS 4.0: Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address? • Traps contain the original Device Agent IP to identify the source (Not the IP of LMS)?• Is possible to configure one logical IP address or Domain Name for redundant LMS:Cisco Security Manager 4.1:Is able to forward SNMP traps (ver. 2c) received from device registered with it to a configurable IP address?• Traps contain the original Device Agent IP to identify the source (Not the IP of Security Manager)? • Is possible to configure one logical IP address or Domain Name for redundant Security Manager?
View 0 Replies
View Related
Mar 14, 2008
Just purchased a RVS4000. How to be successfully able to VPN into this device from os/x? If so what software / settings required.
View 6 Replies
View Related
Jul 18, 2011
Comcast sent out a new modem a few days ago. The reason for this was our internet had gone out for a while, they came in and said our modem was fried. I have internet access by directly wiring from the modem to my computer.My router doesn't work anymore. I have a local network, but no internet access. I'm using a Linksys WRT54G, and I don't really know what to do.As far as I remember, setting everything to defaults and factory settings was how I set up my router in the first place and it just worked.
View 11 Replies
View Related
Jun 23, 2010
I've been into the setup page several times over the years but now it won't load. I recently reset it and want to setup security again.
View 6 Replies
View Related
Nov 17, 2011
I have a Cisco linksys router e1550. My wireless network is working fine, but my wired (PC) is not working?
Removing the router and having the modem connected to my PC works but when I put on my router my wired connection only works for a few seconds to none
So I think the router may be causing it, could it be the settings? Even though there at default.
View 1 Replies
View Related
Nov 16, 2011
About 6 months ago I bought a new router (Linksys E1000 v2.1) which worked great right out of the box. A couple months later I tried to setup a home network so that my two laptops could access a shared drive on my wired desktop, but for some reason they didn't show up as being on the same network. All computers involved are running Windows 7 if that matters.
Upon a recommendation from I friend I put DD-WRT on the router and it worked fine. Setup MAC filtering and WPA2 Personal security. This worked fine for about 4 months until today.
When I got home from work today I noticed my laptop wouldn't pull up any web pages, but it said it was connected. Then I noticed my iPhone wasn't connected either. I restarted my laptop and then it wouldn't connect to the wireless either (I could see the wireless, but I would get a Could not Connect error when I tried to connect to it).
I went to my desktop and it is working just fine, it is plugged into the back of the router. I also have an AT&T MicroCell (cell phone booster) that is plugged in to the back of the router and it works fine too.
I removed the encryption and MAC filtering. I then reset to factory (or "factory" DD-WRT) and now the wireless works, but it is MUCH slower than my desktop. I ran a speedtest on my desktop and got 12 Mbps down and 1 Mbps up. On my laptop, I get 0.03 Mbps down and 0.25 Mbps up.
View 4 Replies
View Related
Nov 29, 2012
Putting this router back in service, I reset (10 and 30 sec hold) until lights flashed. Unplugged it. Came back and connected to computer. Used default u/n = blank and p/w = admin -- doesn't work, can't get to control screen. Tried various combinations and still won't work. How do I get router to respond?
View 9 Replies
View Related
Aug 1, 2012
I have a mac 10.7.4 and an xbox 360 slim. Whenever I try to play online like cod or fifa and someone else is on the computer It is super lagy, Laging. Before when I had a **bleep**y netgear 33 mb it worked perfectly fine. Now this router is has 300 +mb and it stil doesnt work. This router cost me $80 dollars. Before cisco linsys I bought a netgear not the **bleep**ty neatgear but a newer one and it still had the same problem.
View 1 Replies
View Related
Nov 7, 2012
I just received a new modem from my ISP acanac, the modem model is NetVito5300.When I connect the modem directly to my computer, I can access the internet, but if I connect through my wireless router, there's no wireless internet access. Wireless router model is CISCO Linksys E2000.I tried to download Cisco Connect Setup Software for PC and followed the step until one point it asked for my wireless username and password and I put them in correctly but it said my router was not successfully set up and failed. I should press the reset button and set the router to factory default mode, but I'm afraid I won't be able to set it up properly after doing so.What should I do to connect my new modem and wireless router properly so I have wireless internet access?
View 6 Replies
View Related
Oct 17, 2011
I have the 1.0.03 firmware installed and URL blocking doesn't work. I assigned the policy to the entire address range and could still access the web site I wanted to block.
View 1 Replies
View Related
Jan 7, 2013
Trying to troubleshoot a Cisco Pix 501. We have a cable modem/router that goes to the Cisco box that then goes to my wife's computer. It's worked flawlessly since we hooked it up, even if we unplug/replug the router. Today, we unplugged the Cisco box itself to hook up a newer one. When the newer one didn't work, we tried to hook up the old one again to no avail. The led indicators seem to show that everything's working properly. We've unplugged and rebooted everything. Nothing works. The network monitor on the computer shows that it detects being connected to a network, but it always says no internet access.
View 1 Replies
View Related
Apr 1, 2011
I have just changed from cable to DSL. I have a LinkSys BEFSR41 router. I can't get my LinkSys BEFSR41 router to work with the DSL.
View 3 Replies
View Related
Jun 6, 2009
I'm trying to upgrade the firmware of a BEFSX41 wired router from version 1.43.3 (apparently the first revision after the original realease) to 1.52.15 (the latest I found), but I can't get it to finish. I'm using a Mac with all the latest versions of OS, Safari, and Firefox. When I use Safari to initiate the upgrade, it get's to the point where it says "Please wait ! Setup will take a few minute _____" and nothing else happens after that, even after waiting 30 minutes or more. When I use Firefox it gets to the same "Please wait" message, then a few minutes later Firefox displays an error message "Connection Interrupted: The connection to the server was reset while the page was loading. The network link was interrupted while negotiating a connection.
View 9 Replies
View Related
Aug 12, 2011
I'm having a problem with Wake on Lan. (I'll bet you never guessed from the title, eh?). I have an E4200 and I can not get WoL to work over the internet.(I'm assuming it's not actually going out to the internet when I wirelessly wake it using shawn.dynamicservice.com and the subnet, but rather the DDNS name is being resolved through the ARP cache, but I don't know. I'm still learning) Consequently, if the sentence above in parenthesis is correct, I am unable to perform WoL from outside my LAN. What am I missing?
View 3 Replies
View Related
Aug 19, 2012
Buy new one Linksys E3200. Two day using and now have such problem. Every 30 minutes WiFi connection disappears for 10-15 sec. Then appear, but you can't connect to WiFi network for next 30 seconds. Update firmware of router to last version, but it doesn't work.
View 3 Replies
View Related
Aug 19, 2012
I have just upgraded my E3200 to firmware: 1.0.04 build 1 Apr 10, 2012.The guest network SSID didn't show before in my access point list, but now I can't even change the settings on the router.The options are greyed out.
View 6 Replies
View Related
Jan 15, 2012
In the next month or so I plan to replace my old desktop PC. It is currently connected to a Linsys E3200 wireless router. I have many other wireless devices also running off the E3200, but my PC is the only wired device connected to it. When I replace the wired PC do I simply switch the new one in with the existing ethernet connection (I'm sure it is not that simple) or do I have to start over again recreating my entire network..security etc.. ? If so what is the process to start over ? Do I have to reset something on the router, reload cisco connect, create a new network name?
View 4 Replies
View Related
May 1, 2013
I have a E4200 v1, connected with a few PCs by ethernet ports and various devices by wifi. Now the wireless devices work perfectly but sometimes the PC via ethernet ports cannot connect to LAN and internet.
View 2 Replies
View Related
Jul 1, 2012
Type: WRVS4400N Wireless-N Gigabit Security Router with VPN.I bought it last week. Its single port forwarding has an issue. I can only use that function for a couple or hours. Then the forwarding does not work. I have to reboot the router to make it available again.
View 1 Replies
View Related
Jan 10, 2012
I recently bought a Cisco E2500 for work, and after setting the router to Bridge Mode, I am unable to access the router web interface. I tried both the old IP address (192.168.1.1) and the IP address that I entered when I was configuring Bridge mode, but I couldn't get either to work. I have always tried resetting the switch to factory defaults and trying again to make sure I didn't type anything wrong, but to no avail. The wireless and everything works as it should, I just can't get back into the router to change any of my settings.
View 4 Replies
View Related
Jan 22, 2012
I've been trying to port forward my WRT54G2 router.I've tried to update the Firmware, use another computer or another browser.But it still doesn't work!
View 1 Replies
View Related
Sep 15, 2012
I have successfully set up a guest network on my EA4500. Guest laptop associates with guest SSID just fine. Then via IE, it gets prompted for the guest password, which is entered and accepted just fine. At this point guest laptop is on the network.
BUT... at some point the guest laptop will need to reauthenticate (I don't know what the timeout is, but maybe one or two days?). Anyway, it's at this point that IE presents the guest network login page. But now after typing in the password, "enter" or clicking on the button does nothing. It looks like the guest web page doesn't get loaded properly or completely, so the reauthentication can't complete, therefore can't get to the internet. So, while in this state, I've also tried Firefox and Chrome, and same thing, no action when trying to submit the guest password. Tried rebooting guest laptop, and still same problem. Only thing I've found so far that works is to reboot the router. So I'm guessing there's a problem with the guest/web server on the router?? It's a real pain to have to reboot the router every day or two, when I've had other Linksys routers run for months without having to touch them.
I was running CCC 2.1.38 when I first noticed the problem. Since then I've downgraded to Classic 2.0.37, but it seems I still have the same problem. Again, I can connect & authenticate just fine initially, but when reprompted after some period of time, it doesn't work.
I've tried contacting Cisco support, but it looks like I'm at 91 days since purchase and thus outside of my 90-day complimentary support, so they happily provided me with the premium support options just to have the honor of talking with them. Guess I shouldn't have spent so much time trying to figure this out myself.
View 9 Replies
View Related
Feb 28, 2012
I was able to install the RV042 router to my ATT DSL line (WAN1 port-INTERNET) and it gets an external IP address automatically and the Internet works. When I connect my Comcast Internet to WAN2 port INTERNTE/DMZ) it doesn't get an IP address. and the Internet goes down and the WAN2 port ip address says 0.0.0.0.I've tried releasing/ renewing and it still says 0.0.0.0.Everything else is set as the default.
View 1 Replies
View Related
Aug 9, 2011
We have three brand new E4200 routers, all using the most current firmware (1.0.02). They are all in bridged mode, however when I attempt to enable the guest network on each of them, the config shows it as active, but it never shows up as visiible SSID. In previous posts, I've seen people saying that I need to do a complete hard reset of the router and re-enter all the configs again to get the guest network active. Is this true? I'd hate to think that I have to hard reset and reconfigure all three of these APs, just to get the guest network enabled.
View 2 Replies
View Related
Feb 23, 2013
Blank user name and admin in password doesn't work. How to reset these ?
View 1 Replies
View Related
Aug 8, 2012
First time VPN newbie. I need to set up vpn for a friends small business using RV082 so, as a test, I set it up here at my home using a very basic config. The network topology looks like:
cloud => cable modem => RV082 => DIR655 => win7 PC
At a remote site, I fire up QUICKVPN, enter necessary data and successfully connect. Bring up Remote Desktop and put in the IP of my home pc and the logon username and, after a minute or two, it says "unable to connect to the computer" (or words to that effect). My home PC has been configured to allow remote desktop connections and this has occured in the past but not since the RV082 installation. There is nothing in the PC's logs nor in the RV082's logs.
View 1 Replies
View Related
