Linksys Wireless Router :: E2000 With Modem DSL PPPoA Mode?
Jan 23, 2012
I bought an E2000 router with modem Dlink DSL-320B in PPPoA mode. I have already spent much time for to configure the router with-out any positive feedback . I've selected Automatic configuration with dhcp , static ip 192.168.1.2 and dhcp and modem with 192.168.0.1 and dhcp . If i view the status windows (internet connection) in router i see the right address for gateway and internet Ip , but is not allow to navigate by other PC linked with internal switch of E2000. Do you Know some particluar set-up for PPPoA mode ?
View 5 Replies
ADVERTISEMENT
Jul 11, 2011
I have a e2000 router and a wmp600n wireless card in my desktop pc. Everything works fine until I enable 40 mhz for faster speeds in the e2000 router. When I do this the router switches from 20 mhz to 40 mhz and I get the faster speed. But the effect of this is that my pc gets all "choppy". What I mean is that everything freezes up every few sec. For example when im minimizing windows, the windows freeze half way for about a sec then unfreezes. My mouse does the same thing, even my sound is choppy. I have to switch my router back to 20 mhz and then everything is fine again.
Using windows 7 64 bit
Using newest dirvers and firmware from Linksys.
View 4 Replies
View Related
Aug 30, 2011
I am using a E2000 connected to a DSL modem via the internet port. My modem is able to connect at gigabit speed but it doesn't seem to be the case with the E2000. All other ports are running at gigabit speed without problem. Is there any parameter that can be modified or is it a router limit?
View 2 Replies
View Related
Nov 7, 2012
I just received a new modem from my ISP acanac, the modem model is NetVito5300.When I connect the modem directly to my computer, I can access the internet, but if I connect through my wireless router, there's no wireless internet access. Wireless router model is CISCO Linksys E2000.I tried to download Cisco Connect Setup Software for PC and followed the step until one point it asked for my wireless username and password and I put them in correctly but it said my router was not successfully set up and failed. I should press the reset button and set the router to factory default mode, but I'm afraid I won't be able to set it up properly after doing so.What should I do to connect my new modem and wireless router properly so I have wireless internet access?
View 6 Replies
View Related
Dec 25, 2011
So my family has an E2000 setup near the modem in a room that litterally is a DEADZONE, signal bearly gets in or out of this room. I've argued until I was blue in the face that we ned to rewire the internets inlet to the house in to another room that isn't a deadzone and rune a router from there.They IT disadvantaged refused. We have also an E2500 they say hook it up, maybe it will work better (when your in a concrete and mettal room with a router sitting on a shelf surrounded by book and with a corless phone system hooks up and sitting on top of it... its jsut not going to work. is there a way i can take the E2500 and make it an access point for the E2000?
I figure if I can I would take the E2500 and put int in a better location and jsut have it relay the E2000 internet. Because of the IT limited thought process of most of the people living here I'd prefer that they share the same SSID or atleast make for a simple transition for the apes I live with.
View 6 Replies
View Related
Feb 27, 2012
Using a Linksys E2000 and Linksys WRT54GL (both flashed to most recent firmware), I am trying to set up Network "A" and Network "B" on one modem. I do not want either A or B to be able to see each other for security purposes. Both are secured networks for the wireless connections and have different SSIDs.
After online research, and the inability to find my exact question answered, this is what I did and I'd like to know if I'm missing anything to keep A and B completely separate. Or, if I've done anything that will cause any problems on my network. [code]
I disabled the ability to change settings using wireless connection on both routers.
View 9 Replies
View Related
Jun 10, 2011
I recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
View 2 Replies
View Related
Mar 15, 2011
Hardware: Modem-Motorola SBV5222 Router-Linksys E2000(Cisco brand name? I didn't buy the router) I use a PC with windows xp with sp 2 and 3 installed.Problem: I can use the internet just fine when I am connected to the router, my pc is connected directly to the router via cat 5 but when I directly connect to the modem I get limited to no connectivity. I'm not using a proxy server and before the router was set up(I live with roommates who set up the wireless network.) I could connect to the modem just fine. I can't repair the connection since it seems to be unable to renew the ip address. I've also tried to manually configure my ip address though I'm sure it wasn't the issue.I've racked my brain to think of a simple solution and it doesn't seem one is apparent and I'm almost sure it's something to do with xp and I'm not so great with software.
View 4 Replies
View Related
Dec 21, 2011
I have a d-link dsl modem that reports it's getting the full 6 meg download speed from AT&T. I put the dsl modem in bridge mode so the E4200 will do the logon to AT&T with my credentials. If i do a speed check using CNET internet speed test, from both a desktop (wired 1gb card) and any laptop in the house (all draft n 2.4 or 5.0), it ranges anywhere from 3 meg to 4.3 meg. I have 6 cat-e ethernet cords everywhere. I do have 2 switches but have tried to unplug those to see if any difference
View 1 Replies
View Related
Apr 27, 2011
I plug my modem into the router, and apparently to configure it I need to put my settings into the router, but PPPoA is not in the dropdown, only PPPoE and PPTP. What do I do?
View 1 Replies
View Related
Jul 24, 2011
we are trying to configure PPPOA over Ethernet on Cisco 1812 Router, we have 2 ethernet ports and no ATM ports, hence PPPOA must be applied at a global setting.
View 3 Replies
View Related
Mar 23, 2012
I can't get a new IP from my ISP when my Cable modem router(EPC3925) is set to router mode, i have tried factory restore, unplugged etc..but still no luck. It changes each time i reset it when i set it to bridged only mode but then i won't be able to connect other devices to it since it doesn't uses DHCP in bridged only mode. It changes back to the IP i had when i set it to router mode. I don't want to change my router settings to bridged only because it would disconnect the other devices in my house. Why my ISP assigns the same IP address when it's set to router mode but assigns different IPs when it's set to bridged only, how is this possible ?
View 1 Replies
View Related
Aug 21, 2011
I can connect to my router but either way it seems like i can't get any internet access (both wireless and by cable): url...I have tried the steps that the linksys FAQ suggests shall fix this problem, but this has not worked. I have also tried to reset the router without any luck. I know it its not the modem that is causing the problem because I'm wired to it now.On the E2000 every light is blinking as it should be (hence the FAQ) so it indicates that there might be a problem with the connection between the router and the computer (tested on other computers too without success).
View 9 Replies
View Related
Jan 27, 2012
I would like to set the router's dns entries but I don't see how to do that. Basic setup page has DNS setep for the DHCP scope but I don't want to push dns to my pc's. What I am looking to do is to use an alternate dns to what my service provder pushes and still have the abliity to route on my internal network.
View 1 Replies
View Related
Oct 2, 2011
We bought our Linksys E2000 in the summer and went to set it up but something came up... Now we are trying to set it up but cannot find our WPA key... Where can we find this?
View 2 Replies
View Related
Jan 28, 2012
So i can only forward 10 ports on my E2000.Example, one game (Battlefield 3) requires 10 ports (TCP and UDP combined).What about my other games? how can one, if possible, add more ports to the router?
View 4 Replies
View Related
Nov 3, 2011
E2000. I run the setup program, my laptop sees the router and it shows a strong signal. When I try to connect with it, it won't connect.
View 9 Replies
View Related
May 28, 2012
I've been looking around like a madman now in the settings. where can I turn off my WPS ? Just cracked my own PIN within 6 hours with Reaver.
View 9 Replies
View Related
Apr 24, 2011
My internet cut out last week and after calling my ISP I found out it was in fact my router that was causing the problem (regular connection to PPOE works fine). I've only had my E2000 about 2-3 months and have not had any problems with it. I've restarted the router, done a factory reset, upgraded the firmware, renewed the IP and still I cannot get any connectivity. I can access the router UI fine and I get a response from pinging it and also I have tried replacing the cables but that didn't fix the problem either.
View 9 Replies
View Related
Aug 28, 2011
I have an E2000 that I was given as a gift. I would like to use at it my office for a switch at my cubicle where I can connect 2-3 computers simultaneously. I am in a large network and am a user only. When I hooked the E2000 up today my computers would not get internet access BUT my laptop got wireless access and internet.
View 2 Replies
View Related
Dec 7, 2011
I'm using E2000 currently and meet a wireless connection problem. The speed can up to 300M bps. When I confiured the E2000 to band auto (20-40mhz) and my wireless network card to work at also auto (20-40) mode, it always down to 144M speed when connection.
If I changed some settings in E2000's wireless configuration, in the status sheet I can see it works at 40MHZ. But after a while,(5-10 mins) it automaticly down to 20MHZ and my labtop connect only got a 144M speed.
how can I deal with that to make it always keep at 300M connection? Note the previous router I used to connect to my lattop can always keep that speed.
View 2 Replies
View Related
Nov 7, 2011
How can I see "DSL Path Mode" on my WAG54G2 modem, How do i know,the line FAST PATH or INTERLEAVE ?
View 1 Replies
View Related
Nov 14, 2011
I have a E2000 router that would go out and I would have to unplug and replug in every once in a while. Finally it just stopped working completely. I reset the router and now it won't let me connect. I have followed advice given to soembody else on here and went into router settings and cloned the mac, the IP address was there and reset my security settings. It let me connect to the network but not the internet...
View 2 Replies
View Related
Apr 21, 2013
I have a Linksys E2000.
It worked fine until one day, without any change at all, it simply stoped working. I mean, I can still connect through my wifi laptop connection (it shows connected to my router and says that I have an excelent signal). But, I can't reach the internet. But, If I unplug the internet cable, and plug it in my laptop, the connection works fine. A friend told me that this could be caused intentionally by the internet provider, that they would block my signal to avoid me using a wireless router, trying to force consumers to sign their own wireless service. Thus, by this friend advice, I've cloned my laptop's MAC address to the router. It didn't work either.
View 4 Replies
View Related
Sep 7, 2012
I have a Cisco E2000. When i connect to my cable modem directly, I get 30-35 MBps down and about 10 up. When I plug in to my E2000 it does that at first... but slowly over time, the speed degrades, usually down to about 5-6 down and 3-4 up. If I unplug the router, it typically restores full speed, but not for long (a few days maybe). Also, when I unplug the router, it is pretty hot.
View 4 Replies
View Related
Nov 11, 2011
For Xbox 360? currently, whether wired or wireless, my Xbox 360's NAT type is strict, and I am unable to do anything online whatsoever. Is there anyways to set up an exception, or anything that can open my Xbox's connection to my router so I can actually use it online?
View 2 Replies
View Related
Oct 28, 2011
Im using a linksys e 2000
Is there a way to block more than 4 websites, and 4 keywords?
View 4 Replies
View Related
Nov 11, 2011
I have an E2000 router that has an intermittent issue where Bonjour drops out. Suddenly my Apple TV won't see my computers, and my iPad won't see my network printer. This happens whether the Apple TV and computers are connected via wired or wireless interfaces.
Restarting the devices does not solve the issue.
Restarting the router solves the issue (until it happens again...)
My router is version 1.0, with 1.0.04 firmware.
View 3 Replies
View Related
Jan 31, 2012
I have a E2000 for a half a year now.We have been on hollyday for 5 days so my routers has been shutdown.Today it happend 3 times that my complete LAN disconnected for no reasonI didn't have any wired or wireless connection.
View 5 Replies
View Related
Jul 2, 2011
I have the Linksys E2000 and set it up on MacBookPro no problems. My iPhone 3G and my gf's iPhone4 connect no problem. Also, I have an XBox 360 connected via ethernet cable. Her MacBook however is constantly not getting an IP. I set her up with an EZ Key, but every time she connects we have to go through the EZ key process where I run Cisco Connect from my laptop. Why can't she just log in every time? This is frustrating me as all other aspects of this router work fine. I had her plugged into it as well with no problems. Again, it works after a dual computer Cisco Connect cycle, but my computer isn't always home.
View 1 Replies
View Related
Sep 20, 2011
For some reason my new E2000 will not connect to our Charter TV Cable internet service. Another router works fine with same cabling. I have reset EVERYTHING numerous times and cross patched -- hard patched, wireless to where my finers are bleeding. My ISP is DHCP and requires no login. So my router is set to automatically connect. Could the router be defective?
View 1 Replies
View Related
Nov 12, 2011
I got a refurbished E2000 on Amazon. Last night I set it up and when I tried accessing this website [URL], I could not connect to the server. First I thought it's the server problem and let it go. This morning it's the same probelm. I called my local cable technician and he told me it's the wifi router is blocking the website. I called the CISCO guys and they refused as it was out of warranty.
View 2 Replies
View Related
Aug 27, 2012
I want to set up another wireless laptop to access my e2000 but i dont remember the network key, How can I retirieve the key? through cisco connect maybe?
View 1 Replies
View Related
