Router-Linksys E2000 Works / Modem-Motorola SBV5222 Does Not?
Mar 15, 2011
Hardware: Modem-Motorola SBV5222 Router-Linksys E2000(Cisco brand name? I didn't buy the router) I use a PC with windows xp with sp 2 and 3 installed.Problem: I can use the internet just fine when I am connected to the router, my pc is connected directly to the router via cat 5 but when I directly connect to the modem I get limited to no connectivity. I'm not using a proxy server and before the router was set up(I live with roommates who set up the wireless network.) I could connect to the modem just fine. I can't repair the connection since it seems to be unable to renew the ip address. I've also tried to manually configure my ip address though I'm sure it wasn't the issue.I've racked my brain to think of a simple solution and it doesn't seem one is apparent and I'm almost sure it's something to do with xp and I'm not so great with software.
I recently switched from dsl to cable. I have a e2000 router that I would still like to use. The modem I have is a Motorola Surfboard SB6121. It has no options that I can modify. The modem has a built in DHCP server. However, I can't modify it and I don't like the ip configuration it uses. For the time being I have the modem connected to a switch which is working fine. What I would like to know is how to configure the e2000 to use the modems connection. I used PPPoE for DSL and had login information.
I moved to a new house last week, and i have comcast internet which works on cable lines.i have them for years. anyways, i got my own motorola sb5101 modem, which i use for a while now.the problem is that in the new house the modem only works when it is connected to a computer with windows xp, it DOES NOT work on windows vista or 7,also, when i connect my router into it, it does not work either.when i connect it to windows 7 64-bit, it says "unidentified network" and "no internet access" but it works perfectly fine on windows xp 32 bit. (i have 2 xp's and 3 windows 7's)
I'm not that great at networking, I'm pretty much a novice but I'm trying to connect a modem and router to my computer but get around bridging the modem if possible. You see, I am working with AT&T and their dsl modem access page only works for me if the modem is unbridged. If I bridge the modem, I cannot get on the page again to unbridge it while I am trying to hook up my router. When I need them to unbridge the modem, I have to stay on hold for hours. One guy even told me that he did unbridge the modem, but since my internet persisted not to work, he told me my ethernet card went bad of a sudden on my computer. I knew this was incorrect so after a few more hours on hold, I had a lady debate with me that she was not unbridging my modem since it was my ethernet card that was bad and not the bridging. Finally, laughing to herself, she unbridged the modem for me and it worked
Here is what I have: My modem is a Motorola 2210 Style: MSTATEA My router is a Linksys WRT120N
As of right now, I just have a LAN with my modem plugged in through an ethernet cord to my PC. Is there a way of me hooking up my Linksys router to my modem and PC without bridging the modem? If so, where can I find out instructions for this?
My son tried to "speed up" our connection by unplugging modem&router. now can't get both talking to each other. Tried numerous steps! Bought Router 8/11/11, so NO Support from Cisco(only 90 days-POOR!). Website useless. Modem works fine with PC wired in.
So I've had this problem before and normally I solve it by simply unplugging everything from my modem and router but ive tried that this time several times to no avail. The internet suddenly cut out one day and when I did my usual unplugging thing it came back unbearably slow.Right now I'm running off a motorola SB5100 Surboard modem and a linksys WRT54G2 router and its not my computer, everyone in the house is getting terrible speed.
I am using a E2000 connected to a DSL modem via the internet port. My modem is able to connect at gigabit speed but it doesn't seem to be the case with the E2000. All other ports are running at gigabit speed without problem. Is there any parameter that can be modified or is it a router limit?
I just received a new modem from my ISP acanac, the modem model is NetVito5300.When I connect the modem directly to my computer, I can access the internet, but if I connect through my wireless router, there's no wireless internet access. Wireless router model is CISCO Linksys E2000.I tried to download Cisco Connect Setup Software for PC and followed the step until one point it asked for my wireless username and password and I put them in correctly but it said my router was not successfully set up and failed. I should press the reset button and set the router to factory default mode, but I'm afraid I won't be able to set it up properly after doing so.What should I do to connect my new modem and wireless router properly so I have wireless internet access?
So my family has an E2000 setup near the modem in a room that litterally is a DEADZONE, signal bearly gets in or out of this room. I've argued until I was blue in the face that we ned to rewire the internets inlet to the house in to another room that isn't a deadzone and rune a router from there.They IT disadvantaged refused. We have also an E2500 they say hook it up, maybe it will work better (when your in a concrete and mettal room with a router sitting on a shelf surrounded by book and with a corless phone system hooks up and sitting on top of it... its jsut not going to work. is there a way i can take the E2500 and make it an access point for the E2000?
I figure if I can I would take the E2500 and put int in a better location and jsut have it relay the E2000 internet. Because of the IT limited thought process of most of the people living here I'd prefer that they share the same SSID or atleast make for a simple transition for the apes I live with.
I bought an E2000 router with modem Dlink DSL-320B in PPPoA mode. I have already spent much time for to configure the router with-out any positive feedback . I've selected Automatic configuration with dhcp , static ip 192.168.1.2 and dhcp and modem with 192.168.0.1 and dhcp . If i view the status windows (internet connection) in router i see the right address for gateway and internet Ip , but is not allow to navigate by other PC linked with internal switch of E2000. Do you Know some particluar set-up for PPPoA mode ?
Using a Linksys E2000 and Linksys WRT54GL (both flashed to most recent firmware), I am trying to set up Network "A" and Network "B" on one modem. I do not want either A or B to be able to see each other for security purposes. Both are secured networks for the wireless connections and have different SSIDs.
After online research, and the inability to find my exact question answered, this is what I did and I'd like to know if I'm missing anything to keep A and B completely separate. Or, if I've done anything that will cause any problems on my network. [code]
I disabled the ability to change settings using wireless connection on both routers.
I recently borrowed a friend's desktop and I am having issues with connecting with the router through an ethernet cable. I go to troubleshoot the problem and I get "Local Area Connection 2 doesn't have a valid IP configuration". Its nothing with the router because when I plug my laptop in with the same ethernet cable, I am able to connect perfectly.
I am trying to get my parents Kindle Fire to work. They recently purchased a Motorola Modem/Router which is hooked into the desktop and works fine. I want to get their new kindle to work and can not seem to figure it out. Their operating system is Vista which I can upgrade to Windows 7 if that would make it easier. When I click on setup the WiFi part of the installation wizard cd that came with the Motorola it says there is not a network adapter. I know what that is however I do not know why I would need it when the desktop is hooked directly into modem/router and I just need the WiFi for Kindle.
I have a 192.168.1.xxx network connected to Verizon FIOS via Actiontec MOCA / router. I also have a 192.168.15.xxx network connected to Comcast via Motorola VT2442 router (used for Vonage) and a Motorola SB6121 cable modem.
Each network has it's own gigabit switch connected to each router. The two networks are physically separated but switches and routers are physically side by side.
What is the best configuration to allow devices on 192.168.1.xxx network to communicate with devices on the 192.168.15.xxx network (share printers, NAS, etc), but still have each network served by it's respective ISP, and each device still get it's dhcp, dns, gateway, etc from each respective router?
I've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
The inet was working through the router (we get it off our neighbours), now our neighbour is our grandad and he doesnt use the internet (his daughters do but they left home). So we decided to take the router around to our house because the signal would always be very weak in our house (but it worked.) So we connected an ethernet cable, that goes through the roof of both houses attics and into my room, and plugged the router in there. back in the other house, the wire is going into the modem.
So we have the modem in one house, with a big wire going to my house into the router. We turn it on and it works, for like 3 seconds then suddenly, we get the message "No internet access" and "limited internet access" on our XP and windows 7 laptops. On the windows 7 it shows a small yellow triangle symbol with an exclamation mark on the bars too.So I tried turning off firewall, and resetting router and all that, plugging it into modem (which I'm doing now) and have narrowed it down to something to do with the routers settings, because it works fine through the modem. and its nothing to do with the router being in the other house because we even brough the router back and its doing the same thing.I dont understand why something would go wrong just by unplugging the router because nothing was changed. Anyway I tried johnwills steps and here are my results from both my XP and windows 7,
Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp.
C:Documents and Settingsme>IPCONFIG/ALL[code]......
My problem is that my desk top computer only gets the internet when my modem is plugged into my router and the router plugged into the computer.If i unplug the router and just go modem to computer it tells me its not plugged in.
So I have a Westell 7500 Modem/Router with Century Link DSL. I've been running a couple of laptops and my wifi enabled TV on the wireless. A few days ago I got a new desktop PC (Windows 7) and plugged the ethernet cable into it. Everything was great but the wireless was a bit slow for the TV so I plugged that in with an ethernet cable too. No problems for a few days. Today, we had a power blip and everything reset and I noticed that the internet light on the modem was solid red and I couldn't access the internet on any machine (ethernet or wifi). I called the ISP who said there was an outage in the area. A few hours later, solid green light on the modem BUT the TV (ethernet connected), my iphone, and my laptops could NOT connect, despite the network showing up with a full signal. Oddly, my new PC, connected via ethernet was fine so I played some Diablo (side note). Here's the deal: the new PC connects just fine but nothing else will. If I unplug the ethernet cable to the PC or disable the LAN connection, the red internet light appears on the modem. It seems as though the PC has hijacked the modem in some way. Even the TV won't connect with the ethernet cable. The only way the internet works now is if the modem is connected to the new PC. I've done all the resents - unplugged the modem and let it sit for 10-15 minutes, accessed the router settings, etc etc. Why would this start happening now after everything was working well for several days and how do I fix it? I need the wifi connection! Update: Plugged my Macbook Pro into the ethernet cable (took it out of new PC) and it works.
I get this at random times. My internet disconnects until I reset my modem and I don't think it has anything to do with the modem because I had it replaced by my ISP and they did a few line tests and nothing was wrong. What can I do to avoid having this problem anymore? It's been doing it for almost 2 weeks now and when it decides to do it is random.
I have this motorola sbv5121e modem. I can connect one PC to it directly. When I try to connect a secont PC, via a switch, it won't give out 2 IP addresses. Moreover, I see that the one IP address it does give out, is a public one (like 22.x.x.x). I'm on XP and show the addresses with ipconfig. Is this modem defective hardware-wise, or is some setting internally wrong? How can I see what the DHCP server does?
I had to made some hardware changes. All the computers are running windows XP. I changed out to a Motorola 2210 modem, d-link dir-825 router and DGS-1008G switch.Everything was fine until I made this change. I now have internet, but it is slow.
I have a adsl setup from my ISP (TDC) and I would like to use my 887va as modem instead of the supplied Motorola Modem.I have the technical info on the connection: VPI = 0, VCI = 101 and RFC1483 AAL5snap. I have supplied the 887VA with an IP address on VLAN1. What is the right direction in terms of access-lists, dialer interfaces, routing etc.I have tried serveral guides on Cisco pages but have not managed to even ping google from my 887va.
I have an HP Pavilion wireless laptop with windows vista and a gateway desktop, windows XP Home edition and every thing worked ok untill I got a virus on my desktop Since then I've formated the hard disks and reloaded the opering systems, but I don't know how to get the laptop working wirelessly without taking the motorola modem and connecting it directly to the laptop, I have a D-Link DIR-615 router.
I am able to connect with other devices (iPhone, Roku) to my wireless through the wireless router. My computer recognizes the broadband connection, but it won't connect to it. I get two errors when I try to connect:651: the modem has reported an error, and 638: the remote server is not responding in a timely fashion.I have tried connecting the ethernet cable directly to the modem, but I get the same results.Also, I have tried to cycle down the computer, router, then modem and turn them back on in reverse with no change in results.The connection worked until I clicked "disable connection" one day when I had trouble connecting (high traffic i think). Since then, the"home group" I set up originally with the connection wizard disappeared, and it had not been able to connect since then. When I try to connect I click on a small icon in the lower right that says, "not connected, connection available", then I click on the button to connect to broadband and get the errors described above.
I have Qwest DSL 7MB internet with a motorola 3347 Qwest model modem and for some reason throughout the day sometimes fewer than than others my internet light will just go red for about 45 seconds up to 2 to 3 minutes them it starts flashing green again? I called them multiple times but they just say maybe its the modem. Is there any test I can do to see? I upgraded the firmware to the newest one to see if that would work but no luck.
I've been trying to connect my D-Link DIR-601 router with a Motorola SBG901 cable modem. The modem itself has a built-in WIFI (G) and one ethernet port, but not good enough for my purposes. I need more wired connections and an (N) WIFI connection, which the D-Link could provide, if I could get it to work. I just cannot get the two pieces of equipment to talk to each other. I can set up 2 independent LAN's, but no WAN (internet connection) from either. D-Link has provided pages of instrutions, but nothing works.
I was working with Motorola SB6120 cable modem regarding an odd power cycle issue (it would power cycle randomly for 24 hours). While trying to diag the issue, I was taking a peak in his router config and found a port set to forward as:
Application: Comcast Port From: 888 Protocol: Both IP: 192.168.100.1 Port To: 80
I understand that his modem admin page is now available from the internet. He said his friend set this up to "modem", but I don't see any advantage of having this done. At this point what are the other advantages of forwarding such ports?Another key note: When the port forwarding was disabled, suddenly the power cycle issues stopped.
I have a Motorola surfboard sb5101. Provider is comcast.I have never had any problem with my equipment until now. Here is whats going on. I bought a used sb5101 a week ago so that I would not have to pay the rental fee anymore. Comcast activated it, and it worked fine for a week or two. The other night I got disconnected from XBOX live randomly in the middle of a game. Thought maybe just a hickup, no biggie. Well it happened 3 more times in a few hours, then again the next day.So thinking maybe this used modem is bad, I plugged back in the rental from comcast which I still had. Worked fine for a while, then the same thing, random dissconnects after 10 min, 30 min, 2 hrs into a game...etcOn both modems, the 1st and 4th green light are solid, the 2nd and 3rd green light are flashing when the connection from LIVE drops.So I'm starting to think know that neither of the modems are bad. I then try going directly to the modem instead of the router, never had any problems with the router but figured I try.I even went into the attic and got rid of the 4 way splitter that feeds cable into all the bedrooms and put in a 2 way instead hooking up only the cable line im using for xbox. Thought maybe the signal is getting degraded to bad, eventhough never had a problem before.So now I'm practically hooked up right to the line coming off the street, ethernet cord plugged directly into the modem, no router. Still dropping connections randomly with same 2nd and 3rd light flashing.The connection needs to be completely stable for multiple hours.Also, I called comcast when I had to reactivate the rental modem, so they did refreshed that modem and reactivate it, but still had the disconnects the next day.
Would this work ?. also, on the back of the modem is a rectangular, not the typical, usb slot. I cannot move the modem because it is connected to the wall. I don't want to use an extra long wire either. What do I need to buy so I can use the wired modem, as a wireless one on my pc downstairs ?