I attempted a firmware upgrade on my RV042. After an hour, the upgrade was still in progress. I now cannot login into the router using my user name and password (nor the old admin/admin). The router is functioning, but I fear it will eventually fail. How can I recover ability to log in? The Firmward Recovery program doesn't seem to be appropriate for this situation.
View 3 RepliesI have the a problem, when I do a upgrade of a SMB RV042 and the PC that contain the upgrade file is in the same segment of the RV042 the upgrades is succesfull, but when the PC is in another subnet, upgrade fails. There are conectivity betwen the two subnets and there are not a firewall.
View 3 Replies View RelatedTried upgrading my firmware to 4.0.2.08-tm and now I cannot log in via the web interface. The router boots and gets out to the internet. It still allows incoming vpn connections. The login screen displays and will display an error message if I use incorrect credentials, but if I log in properly and am directed to the routers web config homepage at "192.168.1.1/default.htm", I get a 404 error message. Telnet does not work either (not sure if it's on, never used it before) 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.As if the web pages after the login screen got removed or corrupted after the update.
SN is NKS10403247
I realize there is a newer version. Attempted the upgrade incrementally since I could not find documentation specifiying if that was required or not.
I have a problem with a brand new RV042 v3 hardware,I upgraded the firmware from 4.1 to 4.2 and now can not see the web interface in firefox, the login appears and the left menu appears, but at the right nothing is shown
I tried doing the firmware rescue util but the same problem happens.if this a know issue? Should I RMA it?
After upgrading the firmware on my RV042 router to version 1.3.13.02-tm, I am experiencing very slow Internet response on most sites. In some instances, when the page does load, it lacks many graphics. Frequently, I also receive a "server not found"error. In all cases, reloading the page (once it has loaded) results in a complete page display. This is occuring on two MacBook Pros and also on an iPad. The router is a version 1, so no further upgrades are available. I contacted support, but since it is out of warranty, they are unwilling to assist. Prior to the upgrade, everything worked fine, as it has for 5 years.
View 1 Replies View RelatedWe have a CISCO RV042. We are about to begin a VIOP service with Vocalocity who state:
The RV042 is a wired router that requires no configuration adjustments for the firmware versions we tested. Version 1 and 2 are compatible. Version 3 is NOT. Firmware Reviewed: 1.3.12.6 | 1.3.12.19
Our router's firmware is : 1.3.8.2 (Feb 12 2007 10:43:08)
Can we upgrade to 1.3.12.6 or 1.3.12.19? What is meant by Version 1, 2 and 3?
Does the RV042 have the ability to VPN to an iPhone?
View 1 Replies View RelatedI have a switch SRW224G4 from Linksys and doesn't work now after an firmware upgrade!
Simple, here the result when I try to install the firmware "ls_106-12216.ros" or "SRW224G4P_SRW248G4P_image_v1020.bix" that came from your web site!
Here the result for "ls_106-12216.ros"
Calculating file's checksum...OK
Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
[Code].....
I tried to upgrade the firmware of my RV042 router. I downloaded the file (RV0XX-v4.0.0.07-tm-20100819-code.bin) and check the cheksum. When I try to upload it, I have the message "413 Request Entity Too Large". How can I do ? Should I unzip the .bin file (it's about 30Mo) ?
View 1 Replies View RelatedI upgraded my Linksys RV042 firmware to 1.3.12.19-tm and exported the config file, then tried to convert it using RV0xx_Migration_Utility_v1.0.2.2 in order to import it to a new Cisco RV042 (v3). The migration utility returns a config create fail message and fails to convert.
The LOG file ends with:
Get PORT_101 VLAN Group setting fail.
***log end***
how to make this work or how to move config file to v3?
I have done a firmware update at my repeater F5D8233-4. But now I have no access to the webGUI of the repeater. The SSID can be found and I can access the network. But I cannot connect a 2nd repeater now. How can I reset the old firmware?
View 1 Replies View RelatedI just replaced my old rv042 with the v3 and updated firmware to 4.0.4.02. i am looking for the MTU setting but i can't find it anywhere. Where that can be found?
View 2 Replies View Relatedwill updating my RV042 firmware allow me to download larger files? How do I know what version to update to? Our current version is 1.3.7.4
View 1 Replies View RelatedThe entire "incoming log table" is just full of this! It's all the same! This is on the current firmware 4.0.4.02Sep 20 12:49:35 2011KernelOut of memory: Killed process 5385 (iptables). Sep 20 12:49:39 2011KernelOut of Memory: Kill process 5387 (iptables) score 591 and children. Sep 20 12:49:39 2011KernelOut of memory: Killed process 5387 (iptables). Sep 20 12:49:43 2011KernelOut of Memory: Kill process 5389 (iptables) score 591 and children. Sep 20 12:49:43 2011KernelOut of memory: Killed process 5389 (iptables). Sep 20 12:49:48 2011KernelOut of Memory: Kill process 5391 (iptables) score 591 and children. I see no one has a clue. Anyway, added a copy of the log file. It's just streaming out errors. Serious bug in the new firmware.
View 1 Replies View Relatedi got the RV042 and want to update the fw to 4.04.xx . After a few minutes, the browser wanted to perform the update again. I agreed and now, the webinterface isnt available and i cant get a IP from the router. So I tried to reset the router twice. After no success, I performed a factory-reset, which should work when I pressed the reset-button at least for 30 sec.Now the DIAG-LED blinks in a ~5sec rythm.What can I do?
View 2 Replies View RelatedWe have several RV042 routers with older firmware version 1.3.12.19-tm.We have purchased new RV042 routers as hot spare replacement that's coming with firmware version 4.1 installed.
We have a VPN tunnels between multiple sites using the older firmware version.
My question is: Will a RV042 with firmware version 4.1 connect to a RV042 with firmware version 1.3.12.19-tm and vice versa?
I'm about to upgrading our RV042 to RV042G since everything in the Network ist ready for Gigabit except the RV042
I think it's important to mention that another RV042, which is at a 2nd location, will remain for the VPN connection between the two locations. (Older Hardware are used at the 2nd location).
My Question is, are there any known issues, which should be cleared before changing the router.
Mainly issues with configuration migration and compatibility between RV042 and RV042G VPN connections.
I just updated my RV042 to the firmware RV0XX-v4.0.4.02-tm-20110704-code.bin and now im having this error every time that i try to logon in the router? 404 Not FoundThe requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist.
View 7 Replies View RelatedAfter upgrading an RV042 from 1.3.12.19 to 1.3.13.02, it loses connectivity after several hours. RV042 WAN1 is connected to cable modem (WAN2/DMZ is unused), configured to obtain IP Address.
Cold booting all devices, RV042, AP & Cable modem, re-established connectivity. Only to lose connectivity again several hours later.
Reset RV042 to factory default via reset switch and cleared log. Minimal configuration applied (domain name, hostname, ntp, WAN1 bw=8000).
Checked early this morning and no connectivity. Summary screen showed the same IP on WAN1 port. All appeared normal. Clicked renew, and connectivity was re-established. Same IP as before.
The RV042, when running 1.3.12.19, would run for many months without a hiccup.
This is the log entry when I clicked 'renew':
Aug 18 04:12:40 2011
System Log
DHCP lease info: ip[68.202.x.x] mask[255.255.240.0] gw[68.202.x.x]
[Code].....
Clicking 'renew' did re-establish connectivity, but I'm not sure if it's a dhcp issue or not. If I read the log entry correctly, the router has the IP lease for an hour, which means it renews several times successfully. Connectivity is down in the morning after several hours go by without use. I'm not sure if that has anything to do with it. Again, nothing changed but the code and the RV042 ran without problems for months with the 1.3.12.19 code.
We recently had redundant sup cards installed in 2 of our 4507 units after the upgrade I can no longer change Vlan's with the CNA program.I upgrade to the newest version of CNA but that didnt work.
I can still get Vlan information from my 4503's and 4506's with no problem. I figure it is an issue with CNA selecting the sup card to get it's information from?
We are in the middle of some major user moves and changes so I have had 2 of my guys working to move printers on to their own Vlan and some other changes neither is well versed in command line so I set them up with CNA for simple Vlan changes. Now with this out I have to go in and make the changes myself and keeping up with that and my other duties is getting tough.
I have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file. I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'
View 2 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I am trying to upgrade my RV016 hardware version 1, Firmware version 1.3.2 to firmware version 2.0.0. but can't find the file. Locating RV016_2.0.0? I am trying to upgrade to version 3.0.0.1
View 5 Replies View RelatedI've just purchased 2 RVS4000. The units, which are V2, have been shipped with firmware 2.0.0.3. It seems this version suffers from multiple vulnerabilities I would like to fix asap. Unfortunately, I was unable to upgrade to 2.0.2.7.
One one of the units, I went through the upgrade process via the admin interface. It seemed to work, though it got tucked at 100% - which is a known issue, as per the release notes - but then, instead of having my unit upgraded as advertised when going back to the home page. It seems I'm stuck in 2.0.0.3. I tried the upgrade a couple of times without any success before posting here.
On top of that, the other unit I have is on another site, far from where I am at the moment. It is also a 2.0.0.3 firmware. I didn't try the upgrade, as I prefer to be on site when doing this type of things, this will be the case next week. This other unit seems to be much more responsive than the one I tried to upgrade without success. On the one I have now with me, I have plenty of freezes every time, it can take up to 5mn for the device to respond to a query. The other one I'm managing remotely does not show these problems. Also, even though the units are the same, the "faulty" one seems to have issues to keep all the settings properly. For example, key lifetimes get always reset to 0 sec, and I have to fill 28800 and 3600 each time I make a change in the configuration. Again, the remote one does not have this issue.
So my questions are :
- Any info on this kind of issues with the RVS4000 ?
- Is it normal 2 units purchased at the same time, which have been shipped with the same firmware, behave differently ?
- Is it possible I have a faulty hardware ?
I've been having the lockup issue with the SRP527W (in fact this has been an extremely embarrassing situation after spending 4 x what I could have on a Net gear type unit, to do the same task). I've not yet managed to get hold of the new firmware (MR3) as I've not received the email with a link.
On another note, I'm not sure if this has been covered in other posts, but, when my unit stops working (Wireless still alive, no internet) - the CPU hits and stays at 100% and only a reboot fixes it.
I just tried to upgrade the firmware of my WAP54G to the most recent version; however, I got a message on web browser with legend "Update fail" and then I lost the communication with device. Now, I just goty Power and Link LED's, but nothing on Act (green led, indicator of WiFi),I tried to reset using button, and to connect via LAN, but setup wizard is unable to locate the device.
View 1 Replies View RelatedTried up dd-wrt firmware few days back, I do really like it, but I do noticed my DIR-615 E4 Ethernet doesn't like my motherboard bundled Gbps Ethernet with dd-wrt firmware, and it's really un-stable, the link always up and down (Windows always report Ethernet link-disconnected!). So, I tried so hard to get into emergency page with IE8, Firefox with no success, the only browser can get into it is Google Chrome, but file-upload with Chrome always stuck!!! anyway, I found the SOLUTION!
**make sure you have the original firmware from DLink before you started the following procedure**
1. create a html file (dlink-recovery.html) with those following code (I got it dumped from Chrome! I've added "http://192.168.0.1" to form action)
<html>
<HEAD>
<META content="text/html; charset=iso-8859-1" http-equiv=Content-Type>
</head><body><form action="http://192.168.0.1/cgi/index" enctype="multipart/form-data" method=post>
<center><p><font color=blue face=Courier New, Courier, mono size=3><b> <font color="#FFFFFF" face="Courier New, Courier, mono">--
<font color="#0000FF">D-LINK</font></font><font face="Courier New, Courier, mono">Firmware Upgrade System </font></b></font></p><p><font color=blue face=Courier New, Courier, mono size=3><b>
[code]...
2. change your PC network adapter configuration "Media Type" to 10mbps full duplex in network adapter configuration->advance settings (hope you know where!)
3. change your PC network IP to 192.168.0.* (any number except 1!)
4. unplug the power from DIR-615, then press-and-hold the reset button while plugging the power back to DIR-615, hold the reset button until the power led-flashing!
5. use firefox to open the dlink-recovery.html which created from step-1, browse the original-firmware and submit. if success upload, you'll able to see the 'flashing' page with percentage counting up.
I use cisco rvs4000v2. I had to restore the factory settings, and I use Cisco RVS4000 Firmware Upgrade Utility version 1.3. But I did not know that it is for Cisco RVS4000v1. The utility will install RVS4000 firmware v1.3.0.5. Now I can not restore to factory settings.how do I restore the factory firmware cisco rvs4000v2?
View 1 Replies View RelatedI just bought RV042G with serial number NKS16120688 to replace old RV042 which is cannot upgrade to new version firmware(from above V.4).After I connect to my TOT isp modem to new rv042g, the router distributes ip (DHCP), get dns from isp normally but it cannot connect the internet at all.It seems this new firmware is not compatible with tot isp in Thailand while old rv042 with old firmware can run smoothly.I have to try many things such as change wan port, change modem and also buy another new RV016, but results still the same.
View 1 Replies View RelatedI have a rv082 small business router and the current firmware will not apply. I downloaded the v4.04 firmware update and tried to apply it yet the update does not seem to work. I have downloaded it a second time and used the UPDATE FIRMWARE button to load and apply but no change.
View 1 Replies View RelatedCurrently on V1.3.0.5. Looking to upgrade to latest version, however the upgrade firmware page is greyed out. Same under Firefox 9 or IE 8. I have already rebooted router, with no change in behavior.
View 2 Replies View RelatedI have upgrade the firmware on several RV082 (and RV042) model routers, and all of them have had subsequent WAN connectivity loss. The WAN works for a while, then stops working until the router is restarted, then fails shortly thereafter. I would assume it was some configuration corruption on incompatibility with the upgrade, but the symptom has been universal. EVERY 2.x upgrade I've made to a RV082 or RV042 router has exhibited this symptom. Reverting to the 1.3.98-tm firmware fixes the issue.
View 14 Replies View RelatedThis morning i upgraded a remote RV082 to 4.2.0.1 from 4.0.4.1. Numbers could be off slightly since i'm going from memory. I never got the normal acknowledgement the transfer was complete but after an ample amount of time closed the tunnel from my end, re- established my vpn but when i went to log in i received: RV082 firmware upgrade error? The requested server-side-includes filename, /usr/local/EasyAccess/www/htdocs/default.htm, does not seem to exist./quotei googled it and found similar occurrences with earlier upgrades. I'm assuming it didn't reboot itself upon completion of the xfer, at least i'm hoping a cold reboot will correct this but as i'm remote and this install doesn't have an ethernet power controller i'm stuck until monday. Should i bring a spare RV082 just in case.
View 3 Replies View Related