Cisco Routers :: Does RV042 Have Ability To VPN To IPhone
Jan 26, 2012Does the RV042 have the ability to VPN to an iPhone?
View 1 Replies
ADVERTISEMENT
Cisco Routers :: RV042 Firmware Upgrade Fail - How To Recover Ability To Access
Jan 31, 2013I attempted a firmware upgrade on my RV042. After an hour, the upgrade was still in progress. I now cannot login into the router using my user name and password (nor the old admin/admin). The router is functioning, but I fear it will eventually fail. How can I recover ability to log in? The Firmward Recovery program doesn't seem to be appropriate for this situation.
View 3 Replies View RelatedCisco VPN :: IPSec Between Windows 7 / IPhone And Linksys RV042 Using NAT
Jan 31, 2012laptop and iPhone should get access to the private LAN
- Speedport is connected to ADSL with an dynamic IP, but DynDns is activated
- Speedport uses NAT for forwarding ports 500 and 4500 to RV042
- RV042 should be the VPN-server
- LAN should be completely able to be accessed by the VPN-client (network printer, shared folders on windows, remote access ...)
- VPN connection should use IPSec for high security
- NAT-T must been used because Speedport only forwards UDP/TCP-ports and no protocols
I have some questions:
- how should I configure the IPSec on RV042?
- which VPN client software should I use ( NAT-T an Win7 64bit must be supported ) and how should it been configured?
This scenario with VPN-server behind a router should be a common one, but I can't realise it alone.Normally I work as professional supporter for Cisco SMB (since 3 weeks), but this scenario is new for me and I don't know how to solve this problem.
D-Link DIR-655 :: Ability To Use 2 Routers At Same Time?
Oct 21, 2011I have one Cable Modem/Router built in (Netgear CGD24N) and I wish to use two routers (the other being the DIR-655). The Netgear is a fantastic Cable Modem but a ****py router, but I wish to use both. One will be situated upstairs and the other downstairs.I have connected the two at different locations via the wall and the DIR-655 successfully went to the Netgear login page (as I went to 192.168.0.1) but internet connection was not working, whereas the Netgear internet was working. This was connected LAN to LAN.
Another procedure I have tried was connecting to them LAN - INTERNET (INTERNET being the D-link one) and received the following message: "The addressing of the Internet side learnt thru DHCP conflicts with the addressing selected for the LAN side. Internet communications will be disabled until you have changed the LAN side addressing to resolve the problem."
Cisco Routers :: RV180 - No Ability To Change IPSec Settings On Device
Nov 7, 2012I picked up this RV180 router because it has one of the fastest thru speeds of all the routers tested that I viewed on smallnetbuilder. That and it has the cisco name. I grew tired of purchasing wireless home routers every year after they fail. So far the thing is nice with one exception.
I have one device that is essential on my network called an airave. It is a small device similar to a wireless access point that works on springs voice network. The thing essentially makes a small cell tower inside your house and connects to the sprint network through an Ipsec vpn. I have not ability to change ipsec settings on the device on my end. The device works fine connected to the cable modem or to the old slow dlink. When I first connect the thing it works fine for about 5-10 minutes on the cisco. Then the thing loses connection and I lose my cell phone service. Just to test any port conflicts I made this the the DMZ with no luck.
I have also tried a firmware upgrade. I have not messed with any of the firewall settings or port forwarding since DMZ should in theory fix that. I have assigned the thing a fixed IP address but that does not seem to make a difference. It did not on my old router and is mostly just for my sanity and to facilitate the DMZ.
Cisco Routers :: SA 500 - Ability To Send Syslog Events To Multiple Syslog Servers
Jul 7, 2012Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies View RelatedCisco Routers :: Auto / Programmatic UPnP Port Forwarding For RV042 And E4200 Routers
Jan 24, 2013I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
Cisco Routers :: RV042 / RV042G / Small Business Routers With Inter-VLAN Capability
Aug 22, 2012I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies View RelatedCisco Routers :: RVS4000 Does V2 Model's VPN Support IPhone
Jul 30, 2011I've been browsing the discussion groups, and it seems that the RVS4000's VPN feature doesn't support the iPhone. I have one of the new V2 models. Does the V2 model's VPN support the iPhone, or do we still have to look elsewhere for iPhone VPN support?
View 0 Replies View RelatedCisco Routers :: RVS4000 SBR And Non Client VPN IPhone / IPad?
Jan 5, 2012How to make a non-client VPN connection to the RVS4000 SBR with an iPhone or iPad? I realize that I could setup some pass-through VPN just fine, but I would like to connect directly to the router and was under the impression from the Cisco product video and other research that IOS was now supported.
View 0 Replies View RelatedCisco Routers :: Connecting IPhone And IPad To RV220W VPN
Aug 19, 2011I am looking to purchase the RV220W router. I am interested to know if I can use the iPhone/iPad to create a VPN connection to this router.I have seen a lot of conflicting information about this so I am looking for a confirmation.
View 15 Replies View RelatedBelkin Routers :: IPhone 5 Will Not Connect To N750DB?
Apr 17, 2013Old phone iphone 4 connected.
View 1 Replies View RelatedBelkin Routers :: IPhone 5 Will Not Connect To N750DB
Apr 16, 2013IPhone 5 will not connect to N750DB? Old phone iphone 4 connected.
View 1 Replies View RelatedCisco Routers :: Make IPSec VPN Connection From IPhone To RV220W
Aug 22, 2011i have try to make a IPSec VPN Connection from my iPhone to my RV220W.
On the iPhone i get the message "The VPN Server was not found".
It is possible to make a IPSec Connection or only a PPTP ?
Belkin Routers :: F5D8236-4v3 IPhone 5 YouTube Video Playback
Dec 16, 2012IPhone 5 will not play YouTube videos, shows everything else, info and screen pic, but says "playback error" when on wifi. Using a Belkin F5D8236-4v3 router. Works fine otherwise. The IPhone played back video properly on an ATT router. I know how to get to router setup pages but am not very competent in understanding it all.
View 1 Replies View RelatedCisco Routers :: RV 180W - Connect IPhone / IPad Using PPTP To Home Network?
Jan 31, 2012My use case is very simple I want to connect iPhone/iPad using pptp to my home network. I purchased the 180W and looks like I am not able to connect mobile devices to it. My Setup is simple I have ST536v6 (firmware 7.4.4) modem in bridge mode and Cisco RV 180W connect to my ISP using Ppoe. I followed the Admin guide and created the pptp user. If I connect from internal network it connects but when I try to connect the device from WAN it just does not work.
Cisco RV 180W
Firmware Version:1.0.1.9
Belkin Routers :: F5D8236-4 - Wireless Printing From Apple IPhone Or IPad?
Dec 30, 2012Does my Belkin F5D8236-4 ver. 1 (firmware 1.00.02) router support Apple's Bonjour print application. I can't get my iPhone or iPad to recognize my new HP Photosmart 7520 wireless printer which is connected to my network through my router.
View 4 Replies View RelatedCisco Routers :: RV042 Won't Get Second IP
Feb 27, 2012I have two Internet connections-
1-DSL Modem (WAN1-Internet Port)
2-Cable Modem-Comcast (WAN2-DMZ/Internet Port)
I connected the DSL (WAN1-Internet) port in and the Cisco RV042 was able to get an IP automatically. I tested the connection and it works just fine. Then I connect the Cable Modem-Comcast (WAN2-DMZ/Internet Port) in and I have the RV042 automatically optain IP address. But it just says 0.0.0.0. I've tried release/renew and that does nothing. Also, when I connect the 2nd Internet connection the Internet goes down. The only way it goes back up is when I disable under the PORT MANAGMENT setting.
All the settings have been kept to the default.How can I get the router to obtain an IP address from the Cable Modem-Comcast (WAN2 DMZ/Internet Port).
Cisco Routers :: NAT Over VPN On RV042
Mar 6, 2012We have an Cisco RV042. We need to setup a VPN with a business partner who is already using our current IP scheme on another VPN with another client. They have asked us to NAT our IP's from 192.168.25.x to 192.168.245.x
I can't seem to figure this out on this router. I have done it on a Sonicwall and Watchguard, but can't seem to get it to work on the RV042.
I have setup the VPN and the One-To-One NAT. The tunnel will connect (using the 245.x IP as our local IP on the VPN setup), but no traffic will pass through.
Cisco Routers :: Rv042 Configuration With Vpn?
May 20, 2012i was planed to make a vpn over rv042 so i get the rv042 connected behind a thosmon 456(configured as a bridge) and 1 static ip ... and i configured the vpn and worked great ...but due to some circumstance i get a package of 6 ips insted of the old ip , so when i try to configure the router with the ISP they but the wan ip 10.232.x.x and told me that an internal ip from there lan ... and give me the 6 ip of 196.x.x.x to use as 1 for internal interface for the rv042 and 5 for the pc's,now the vpn not working anymore...notice: when try to configure the vpn tunnle in the local securty setting i mark the ip only and the ip that abear is the wan ip 10.232.x.x but i can't ping that ip beside i can ping the internal ip of the router 196.x.x.50does rv042 can support static and virtual ip inside the lan |! can i configure the thomson as pppoe and use one static ip from 196.x.x.x as wan ip for it ... and use anther 196.x.x.x ip for the rv042 to get access from outside and connect the lan to the rv042 with internal ip 192.168.x.x ...so i can access the vpn from outside .....and can connect the device i need to use static ip to the thomson ...
View 0 Replies View RelatedCisco Routers :: RV042 - Bug Found In VPN?
Sep 23, 2011Firmware v4.0.4.02 has a nasty bug in the VPN section. If you switch to "IP by DNS Resolved" (yes, it says "Resolved" instead of "Resolution". Gotta love all the Engrish in the RV042!), it will automatically populate the field with "@yourdomain.com". This will cause the VPN to not lookup the proper IP address. Simply deleting the atmark after it populates will fix the problem.
Let's see what happens when we validate a Cisco RV042 webpage:
Errors found while checking this document as HTML 4.01 Transitional!
Result: 353 Errors, 1 warning(s)
Don't even get me started on the horrible Javascript...
Cisco Routers :: RV042 To ASA VPN Not Coming Up?
Apr 24, 2013i am trying to make a simple Site to SiteVPN between two offices, one has Cisco ASA and one has RV042 router.when traffic initiated from ASA side, i keep getting this message in Debug and tunnel wont come up
.
[IKEv1]: Group = A.A.A.139, IP = A.A.A.139, Queuing KEY-ACQUIRE messages to be processed when P1 SA is complete.Apr 26 00:15:53 [IKEv1 DEBUG]: Pitcher: received a key acquire message, spi 0x0
whereas if traffic initiated from RV042 side, i keep getting this message in debug and tunnel wont come up.
Apr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, Oakley proposal is acceptableApr 26 00:43:44 [IKEv1 DEBUG]: IP = RV.RV.RV.139, IKE SA Proposal # 1, Transform # 0 acceptable Matches global IKE entry # 6Apr 26 00:43:44 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: IP = RV.RV.RV.139, Connection landed on tunnel_group RV.RV.RV.139Apr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, Freeing previously allocated memory for authorization-dn-attributesApr 26 00:43:45 [IKEv1]: Group = RV.RV.RV.139, IP = RV.RV.RV.139, PHASE 1 COMPLETEDApr 26 00:43:45 [IKEv1]: IP =RV.RV.RV.139, Keep-alive type for this connection: DPDApr 26 00:43:45 [IKEv1 DEBUG]: Group =
[code].....
Cisco Routers :: Enabling 6rd On RV042?
Sep 27, 2012Apparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
Cisco Routers :: Unable To Log Into RV042
Aug 28, 2011I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies View RelatedCisco Routers :: Can't Connect With RV042 VPN
Jan 14, 2013I have a Cisco RV042 VPN Router and I have added a group vpn, but when I am trying to connect I got an error that the remote vpn server isn't responding.
Here's my log:
2013/01/15 12:24:53 [STATUS]OS Version: Windows 7
2013/01/15 12:24:53 [STATUS]Windows Firewall Domain Profile Settings: ON
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]Windows Firewall Private Profile Settings: OFF
2013/01/15 12:24:53 [STATUS]One network interface detected with IP address MY HOME IP
[code]....
If I am trying to connect the status of the vpn user in the remote interface is "online".I have deactived my firewall at home and at the server for testing purposes.
Cisco Routers :: Configuration Of RV042 VPN
Apr 19, 2012I am looking to configure RV042 for VPN access to local machines and Win 2008 server. The story: Had issues with remote printers being created for clients logging into old Linksys RV042 with Linksys VPN software. First Tech exposed server without security, and it had to be removed as it was being attacked, but did not fix printing issue. 2nd tech could not get VPN to work after 1st tech. 3rd tech, 4hours, and I got that the router is a piece of ... So I'm out over 1000, and not able to have a simple router set up. The present situation. New RV042 with firmware V4.1.1.01, using Cisco VPN client 5.0.07.0410, most XP 32 bit machines coming into network, one 64 bit win 7. My clients have been unable to access their data for too long.
View 3 Replies View RelatedCisco Routers :: Setting Up VPN On RV042?
Feb 6, 2012Is there any documentation out there on a step-by-step instructions on setting up a vpn on a RV042 router?
View 1 Replies View RelatedCisco Routers :: Set Up 2 Subnet With Two RV042?
Apr 30, 2012I'm trying to set up 2 subnet with two RV042 routers. One router will act as a gateway and both WAN ports will be used by two different isp connection. The first router (gateway) LAN IP will be 192.168.0.1/24. I would also like to set up another router behind the gateway with with separate subnet 192.168.1.X/24. And I would like clients on the 192.168.1.x subnet to use the internet through the gateway router and clients on the 192.168.0.x subnet to access resources on the 192.168.1.x subnet. Am I able to do this with two RV042?
View 6 Replies View RelatedCisco Routers :: RV042 V3 / Out Of Memory
Sep 2, 2012The issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
Cisco Routers :: RV042 Drops VPN?
Nov 11, 2012I have an RV042 connected via VPN to the office (to a LinkSys DFL-700). Sometimes the VPN is dropped and never activates again. In this state, if I try to connect to the WEB interface, I can log in, but the router hangs at the login screen. I have to power recycle the router to make it work again.
Updated to latest firmware 4.2.1.02 for V3 hardware. The funny thing is that services from the WEB routed through to local IP adresses on the lan is still accessible. I have setup PPPT VPN on the router, and that also fails to work.
Is there, as a workaround, any possibility to access the routers reset page or access via TELNET to reset the router? This migth be useful, when I'm out. (I have a backup solution to access the local network at home).
Cisco Routers :: RV042 And AT&T DSL Configuration
Jun 29, 2012I have just purchased the RV042 and while it is working great on WAN1 over Xfinity/Comcast broadband, I'm unable to get it working with my AT&T DSL for WAN2. I am planning on running this in failover mode - not load balancing.
The DSL modem it is connected to is a SpeedStream (hooking up laptop directly works etc. etc.). The SpeedStream is set to PPOE authentication passed in via the computer (in this case the RV042). On the RV042 side, I set it to use PPOE, using the credentials as given my AT&T DSL. The DNS servers are set to the ones recommended
Cisco Routers :: Are RV042 And RV082 SIP Aware?
Jul 18, 2012Are the RV042 and RV082 routers SIP AWARE?I haven't had any luck finding documentation stating such.
View 2 Replies View RelatedCisco Routers :: RV042 Can't Ping Ip Server
Feb 6, 2012i have setup vpn connection (client-gateway) using quick vpn ( default cisco) and third party like thegreenbow. connection is ok (established) but why from outside I can only ping to IP LAN PC , if I ping ip server the result is request time out(failed). I have been trying do this to 3 server ( windows server 2003 as OS).four your information I have made firewall "OFF" on all of those servers. the result is same, failed.
View 0 Replies View Related