Cisco Routers :: RV042 Migration Utility Returns Config Create Fail Message
Aug 5, 2011
I upgraded my Linksys RV042 firmware to 1.3.12.19-tm and exported the config file, then tried to convert it using RV0xx_Migration_Utility_v1.0.2.2 in order to import it to a new Cisco RV042 (v3). The migration utility returns a config create fail message and fails to convert.
The LOG file ends with:
Get PORT_101 VLAN Group setting fail.
***log end***
how to make this work or how to move config file to v3?
View 1 Replies
ADVERTISEMENT
Sep 18, 2011
I tried to use Migration Utility v 1.2.2.0 with configuration file from older unit having VPN tunnels and application is crashing with windows MFC error(on several computers, so it is not related to PC).Migration from V2 to V3 of configuration not having VPN tunnels went ok.
View 4 Replies
View Related
Dec 26, 2011
we have some RV042 Routers with Firmware 1.3.12.x we would like to replace with the new V3 hardware.
We downloaded the migration utility 1.0.2.2, which crashes for at least one device.
The release notes for the utility are for version 1.0.2.8, where some crashes seems to be fixed, but where can we download this actual version?? I can only see the (older) 1.0.2.2..
View 3 Replies
View Related
Feb 1, 2012
I'm running a new RV042 with the latest firmware (4.1.1.01). I set it up about 2 weeks ago and have been running it without an issue. Today I tried to go in to the web utility to make some changes. I was prompted for the userid/password, which it appeared to accept (if I typed in the wrong ones it rejected it), and then the screen went blank (normally I would get the status screen now.) Instead the screen I get is the light blue of the log-in screen, but there is nothing on it. The router has switched to the page https://192.168.1.1/home.htm I have tried different browsers and accessing it from different computers - the situation is always the same. I have power cycled the router, and there is no change. I suspect the next step is a manual reset to factory defaults - but of course I would rather not (as I didn't save all my settings of course!)
View 2 Replies
View Related
Sep 27, 2012
I have the a problem, when I do a upgrade of a SMB RV042 and the PC that contain the upgrade file is in the same segment of the RV042 the upgrades is succesfull, but when the PC is in another subnet, upgrade fails. There are conectivity betwen the two subnets and there are not a firewall.
View 3 Replies
View Related
Mar 7, 2012
I am trying to create a bash script to log into routers and make config changes.I ran into a snag in that I am unable to pass a password for the ssh login.I tried tying an expect script to handle that piece but was unsuccessful.I saw on google something about public/private ssh keys (not the same type used to ssh into the box) but I do not want to go this route.Can this be done in another language other than a bash script?I would like to avoid TCL or EEM if possible, I want to learn a language that I can use for multiple purposes.
View 15 Replies
View Related
Feb 6, 2012
I am getting the message '400 bad request' whenever I try to backup the configuration or export a certificate under Certificate Management.
View 1 Replies
View Related
Oct 3, 2012
I don't seem to be able to find a migration utility for PIX rel 8.0.4 to ASA 8.6 is there one available will save a lot of time
View 1 Replies
View Related
Dec 21, 2010
I am working through the migration from ACS 4.1.4 on Windows Server 2003 to ACS 5.2 on the appliance. I have created the 4.1.4 migration server, installed the software and imported the data from our production ACS 4.1.4 box. I downloaded the migration utility from the 5.2 ACS server and am attempting to run on the 4.1.4 migration server. The question that fails is:
Enter ACS 4.x Server ID:
I do not know what this means and do not see anything on the 4.1.4 server that identifies the Server ID. I try localhost and it does not work and the 4.1.4 server is not registered in DNS or I would try that (and . are not valid characters in the ID so the IP does not work).
How have other people handled this question? Is there something that can identify the local server ID?
View 9 Replies
View Related
Jan 31, 2013
I attempted a firmware upgrade on my RV042. After an hour, the upgrade was still in progress. I now cannot login into the router using my user name and password (nor the old admin/admin). The router is functioning, but I fear it will eventually fail. How can I recover ability to log in? The Firmward Recovery program doesn't seem to be appropriate for this situation.
View 3 Replies
View Related
Apr 24, 2012
Our detail is "RV042 V03" and using 2 bridge mode modem.
After i upgraded a new firmware v4.1.1.01-sp (Dec 6 2011 20:03:18) , i got many problems in NSD. Both of Modem always hang 5-6 times a day. And today, i just saw the log line :
Apr 26 03:31:16 2012 Kernel last message repeated 2 times. ( It takes around 5-6 times per hour)..
View 2 Replies
View Related
Jul 26, 2012
I am trying to migrate an ACS 4.1.1(24) using the migraton tool to ACS 5.2. The tool is working OK. It migrates the users, groups, NDG, etc. and the reports are showing no errors.
The problem is with the Enable password of the users. The users in the ACS 4 have the TACACS+ Enable Password configured, but after the migration it appears empty in the ACS 5.
View 3 Replies
View Related
Dec 18, 2012
i'm trying to set up a simple VPN (client to Gateway), but i can't ! An SSL VPN or an IPSEC VPN, whatever..
The firmware of the RV042 is up to date, and i'm trying QuickVPN as a client vpn (also updated...)
My configuration details :
I'm in : 192.168.2.14 /24
My RV042 : 192.168.2.250 /24
And the VPN intend to connect me to : 192.168.4.x
[Code].....
View 5 Replies
View Related
Feb 20, 2012
I have a Cisco ASA 5505 and a Cisco/Linksys RV042. I would like to crerate a site to site VPN between them, and from what I've read it is possible. So I set up the connection on both routers but When I click on connect on the RV042 nothing happens. I've made sure that the encryption settings are the same on both routers but I can't get them to connect to each other. I think the problem may be with the RV042 as the ASA has other site to site VPN connections without any proble (although they are on other ASAs). I saw this thread [URL] but I'm not sure how to disable phase 2 on the RV042 or enable it on the ASA.
what setting I need to change on either router to make the site to site work?
View 2 Replies
View Related
Jul 26, 2012
I am just wondering if it is possible to have two user accounts in Cisco RV042 V3 (Firmware: v4.1.1.01-sp (Dec 6 2011 20:03:18). User accounts to mean that one user can access the router with an administrative level access can do all the changes and management of the router's configurations and settings while another user can only do viewing of the system summary tab and connect and manage the simple configuration to connection to the ISP in both WANs, like setting up the connection type and release/renew the ip address for dynamic ip assigned by the ISP DHCP server.
View 1 Replies
View Related
Jul 18, 2011
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
Message was edited by: Adrian Torres
View 7 Replies
View Related
Jan 22, 2013
Customer has a ASA5540 at their main location and need a new ASA5500 for a DR site.
Can I simply take a config file from an ASA5540 and easily drop it on an ASA5545-X or what ever?
They are going to be using it as a VPN concentrator primarily.
Or are there going to be issues since the 5540 is running 8.4(5) and the 5545-X? Or if they upgrade to 9,0(1) or higher, then they should be the same?
View 2 Replies
View Related
Apr 10, 2011
I have two ASA5510 configured in an active/standby failover configuration. Everything is working well, but I would like to remove DMZ2 as it is no longer needed. On my DMZ2 interface, I have removed the security level and the IP address and shutdown the interface. However, when I do a "show failover" DMZ2 is still showing up. I would like to remove it completely so that failover isn't even "monitoring" this interface. What command am I missing or what do I need to do to completely remove this interface from this "show failover" listing? [code]
View 7 Replies
View Related
Jul 29, 2012
I think I'm missing a basic step here. In setting up a RV220W device behind either a cable modem or a DSL modem, the address that is being returned is not the public IP address of the modem, but rather the private IP address assigned by the modem to the RV220W. Doesn't matter for normal web access but trying to set up a VPN tunnel fails due to the inaccurate IP address.
If I do the same thing but use the dyndns.com application on a computer behind all of this (connected on the private LAN of the RV220W via cable), it reports the external IP address correctly. That works in some locations if I have an always on computer to load the application to. In some cases, however, there isn't such a computer to leave dedicated to running the separate program.
Since this works, and the RV220W doesn't, there is some difference between the Cisco implementation and the dyndns.com implementation.
So, is there a way to get the RV220W to return the true external IP address, or is it stuck returning a private address?
View 6 Replies
View Related
Jul 12, 2011
Does 6rd working on the DIR-601?
For example if I enter the Comcast 6rd parameters:
6rd IPv6 prefix 2001:55c:: /32 6rd border relay IP address 69.252.80.66
I then click on "Save Settings". Now I get a pop up message that says "Invalid IP address" I'm running firmware 1.02NA
View 7 Replies
View Related
Oct 10, 2011
In our company we use the ACS 5.and i have a small problem, what we need to do is.create a profile that will allow SHOW RUNNING CONFIG but not configure terminal.i am investigating and im a littel bit lost i have created a new group but i dont see any option to put permissions.
View 1 Replies
View Related
Aug 2, 2009
I need some info on how to open an RV042 config backup (.exp) file. I recently had an RV042 that got very wet and it is now dead, and I do not have another on hand. BUT I do have the config Backup that includes the user MAC authentication list that I really need. Is there a way to get this information other than loading into another RV042.
View 4 Replies
View Related
Dec 3, 2012
Everytime I make a config change to one of the contexts on our ACE20, I get this message: Config Application in Progress. This command is queued to the system
If I run show download info, I get:
context : context1
Interface Download-status
--------------------------------------------------------------
187 In Progress
199 Pending
Regex download optimization status : Couldn't get status[TNRPC Timed out]
It eventually seems to complete, but it takes a very, very long time. We are running Version A2(3.5) [build 3.0(0)A2(3.5)].
View 2 Replies
View Related
Apr 6, 2013
I use cisco rvs4000v2. I had to restore the factory settings, and I use Cisco RVS4000 Firmware Upgrade Utility version 1.3. But I did not know that it is for Cisco RVS4000v1. The utility will install RVS4000 firmware v1.3.0.5. Now I can not restore to factory settings.how do I restore the factory firmware cisco rvs4000v2?
View 1 Replies
View Related
Jun 7, 2011
I have a problem with the router Linksys RV042, I made a backup of it that contains a file with the extention .exp Now we have buy a new Rv042 made by cisco and the backup file is .config the question is how I convert the .exp file to a .config file so I can Restore the backup in to the new router?
View 1 Replies
View Related
Jan 14, 2013
I just set up a new Linksys/Cisco RV082 router with the intent to get VPN working from outside the building. I have gone through the setup and while everything looks good, I have not been able to connect yet. I have tried everything that I know how, and am now hoping to get the answer from some pros.
Here's my setup. We use Comcast Business class internet. The modem is plugged into WAN port 1 on the RV082. I'm using the router as a DHCP server, that is working fine. My local subnet is 192.168.0.0/220
Right now all I want is to be able to log in as a client using QuickVPN. I set up one user and a client to VPN tunnel using the router's config page. Here's the settings I have:
Tunnel Interface is setup on WAN1, checkbox is enabled.
Local Group Setup
Local Security Gatewaytpe: IP Only
Local Security Group Type: Subnet
[Code]....
It seems like something is blocking the connection, but seeing that I have tried this after disabling the firewall completely it doesn't make sense to me. I also went into the config page for the modem and set up the router as a DMZ. I have also tried connecting with the client built into Windows 7, but that doesn't work either, I just get "connection failed with error 619"
I have the port in QuickVPN set to auto, but have tried both 443 and 60443 with same results.
I ran a port scan at [URL] and it shows I have 3 ports open...80,443, and 1723
View 4 Replies
View Related
Jan 1, 2012
I have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not. Bad router? Bad setup? Bad owner?
View 1 Replies
View Related
Nov 22, 2011
We recently upgraded to Windows 7 at work and my laptop was part of the first deployment. Laptops are imaged so that all configurations/software are already set and done. My problem is as follows, my laptop is part of domain, when I am at work I can ping anything just fine (network computers, printers) BUT when I am at home, I can't even ping my own PC. It returns back with the same address over and over. No matter what I ping when I am at home, it returns back with the same address. I can ping blah and it will display same address over and over. The weird part is I can ping websites no problem, but if i ping random names it will format as follow.Lets say I want to ping lost, below is what i get (I made changes to hide domain and IP)
Pinging lost.domain.com [70.99.199.99] with 32 bytes of data:
Reply from 70.99.199.99: bytes=32 time=57ms TTL=50
Reply from 70.99.199.99: bytes=32 time=58ms TTL=50
Reply from 70.99.199.99: bytes=32 time=57ms TTL=50
Reply from 70.99.199.99: bytes=32 time=58ms TTL=50
[code].....
Notice how my domain always shows up? When I am connected to the VPN at home, I have to log onto our intranet using the IP, I can't use the name, it wont direct to it.
View 2 Replies
View Related
Feb 22, 2012
We have two Cisco 2960 TT-L switches. I'd like to reduce single points of failure and have dual servers for most tasks. For example, two firewall servers and two web servers. Should one server fail the other will act as a failover.I'd like to extend the redundancy to the switches, and am thinking of connecting one web server to one switch, and one to the other. In the event a switch failed a set of servers would still run, and be able to talk to each other.I'd like to run two VLANs, one for the LAN, and one of the WAN, and connect the two VLANs on each of the switches with the associated VLAN on the other switch.
View 3 Replies
View Related
Dec 27, 2011
ASA5510, ASA 8.0(4), ASDM 6.1(5), this is a productino ASA with plenty of lookups working through its 3 interfaces - outside, inside, dmz. The problem is a new use. I've segmented a switch on the inside network with a VLAN, and have a workstation routing through the switch to the default VLAN where all other hosts on the inside network reside so far. The ASA inside interface is the default gateway for the inside network. My test worksttion can PING inside hosts, so the static route is OK.
ASA 10.1.1.2/16 DNS Server 10.1.5.1/16
| |
------------------------------------------------------------------
|
Switch 10.1.8.20/16
[code]....
But lookups fail, Wireshark says the test workstation sends, the dns server receives and responds, but the test workstation never receives. I used the Packet Tracer tool, it gets to the last step syayin OK then finally "inspect-dns-invalid-pak". I can't find any more there to tell just what is invlid about it. So I'm trying to figure out global inspection. Here's an extract from the config:
class-map inspection_default
match default-inspection-traffic
!
!
policy-map global_policy
class inspection_default
[code]....
View 26 Replies
View Related
Feb 20, 2011
I’m currently training to take my CCNA, So for the reason I’m here, I have just been asked to take over the company network.And I need to know how I go about configuring some base level routers.I have 3 remote sites and 1 main site, all these routers are using 857’s, with a VPN tunnel between them, this is running all OK and working fine,But my boss has decided to have a second ADSL line installed in the main site for failover.How do I go about configuring this, ie how do the VPN’s terminate on the other router when the main one goes down?
View 1 Replies
View Related
Jan 24, 2013
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
View 2 Replies
View Related
Aug 22, 2012
I was looking for a small business router that has VPN support and dual WAN support for load balancing. Upon reading reviews, I think RV042/RV042G is a good choice. Now am thinking if it supports intervlan/ router-on-a-stick configuration?
View 5 Replies
View Related
