Cisco WAN :: 6509 IOS Upgrade With ISSU

Jun 7, 2011

We are trying to test ios upgrade for Cisco 6509 switch with issu (in service software upgrade). We were able to upgrade the ios but there is one issue in issue 6509's supviseengine720 gigabit port lost the connection during the upgrade process.

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: 6509 To 6509-E Chassis Upgrade?

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

     x3     48 ports
     x1     NAM
     x2     Sup720
     Running 12.2(18)SXF3
 
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco Switching/Routing :: Upgrade Of 6509 To 6509-E Chassis

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

x3     48 ports
x1     NAM
x2     Sup720

Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco WAN :: 6509 With Sup 720 Configuration Upgrade

Jan 20, 2011

I currently have this in our Sup720:
 
boot system flash bootflash:s72033-jk9o3sv-mz.122-17a.SX3.bin
boot bootldr sup-bootflash:s72033-psv-mz.122-17a.SX1.bin
 
I downloaded s72033-mp001-pz.122-33.SXH5
 
I read the documentation on Upgrading Software Images on Catalyst 6000/6500 Series SwitchesURL

I was wondering do I copy the s72033-mp001-pz.122-33.SXH5 to the sup-bootflash and bootflash?  In the example it also uses disk0: but I get a <No device available>. Also keep in mind we're upgrading the application and maintanence partitions also. So this is a big upgrade and I've never done this before.
 
I guess the 2 things I want to know is:
 
1) Can I copy the s72033-mp001-pz.122-33.SXH5 to both the sup-bootflash and the bootflash?  Can I run it just copying it to the sup-bootflash?
2) It was my understanding that I only needed one image file for the upgrade but the documentation says I need
    "a. the main software image
     b. the bootloader image"
   Do I need another file?  I'm a little confused.  I did notice the files had different names and sizes and so do the ones on my current Sup 720.
 
And we are doing this tomorrow and I just happened to be reviewing the documentation one more time and somehow missed this.

View 8 Replies View Related

Cisco WAN :: 6509 - How To Upgrade IOS On SUP2T

Jan 15, 2013

Have a new 6509-E router with 2 sup2T blades. However it came with IPbase and we need to put Ipservices on it. I have copied ipservices IOS to bootdisk and slavebootdisk.
 
However I cannot get get to the boot command to point to bootdisk. It only allows me to point to flash:
 
)#boot system flash ?
WORD  System image filename
<cr>
 
Yet I don't seem to have an option to copy this new IOS to flash. How do I get to copy it to flash:
 
Here is the original show boot command:
 
sh boot
BOOT variable = bootflash:s2t54-ipbasek9_npe-mz.SPA.150-1.SY1.bin,1;
CONFIG_FILE variable =

[Code].....

View 1 Replies View Related

Cisco WAN :: Choosing IOS For Upgrade On 6509 MSFC2

Jan 19, 2011

I need to upgrade IOS on my 6509 MSFC2. Below is the software version I have on the Sup2 and msfc2. The reason I need to upgrade the msfc2 IOS is that I need to implement ip sla/object tracking and it is not supported by the current version of IOS on msfc2. How do I select the new IOS that I should upgrade the msfc2, in order to achieve object tracking...I see a long list of IOS in the software download section of 6509 msfc2, but not sure which one to choose..
 
WS-X6K-SUP2-2GE: Sw : 8.6(4)
WS-F6K-MSFC2: Sw : 12.1(19)E1

View 4 Replies View Related

Cisco Firewall :: 6509 Possible To Upgrade To Version Of 4.X

Jun 10, 2011

I just need to upgrade existing FWSM of 6509.FWSM Firewall Version 2.3(1)is it possible to upgrade to the version of  4.X .If not  to which  version is safe?And also I need to steps of doing FWSM upgrade.

View 1 Replies View Related

Cisco Switching/Routing :: Getting 6509 VSS IOS Upgrade?

May 15, 2012

Tonight we were performing an IOS upgrade on our 6509 VSS to 122-33.SXI6.  Both 6509's have dual Supervisor cards installed.  Initially we had problems with switch 2 slot 5 supervisor returning to rommon however switch 2 slot 6 supervisor loaded correctly.  After manually setting the boot var in rommon, switch 2 slot 5 supervisor reloaded correctly.
 
After all supervisor's were online we noticed when looking at " show switch virtual redundancy" that sw 1 & 2 slot 6 supervisors were running the correct IOS version but sw 1 & 2 slot 5 were running different IOS versions, however when looking at the show version we are running on the upgraded IOS???  See output below...
 
Why the active supervisor has loaded the incorrect IOS the VSS is running on the upgraded IOS?  I have verified the IOS was copied correctly to each supervisor bootdisk, I see no issues. 
 
My Switch Id = 1                Peer Switch Id = 2        Last switchover reason = none    Configured Redundancy Mode = sso     Operating Redundancy Mode = sso
Switch 1 Slot 5 Processor Information :-----------------------------------------------        Current Software state = ACTIVE       Uptime in current state = 3 hours, 38 minutes                 Image Version = Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXI9, RELEASE SOFTWARE (fc2)Technical Support:

[code].....

View 3 Replies View Related

Cisco Switching/Routing :: 6509 VSS IOS Upgrade

Jan 15, 2012

Will I be OK doing a eFSU Upgrade from s72033-ipservicesk9_wan-mz.122-33.SXI2a to s72033-ipservicesk9_wan-mz.122-33.SXJ1?
 
I only have a single supervisor in each chassis.
 
Should I be ok with just following the eFSU upgrade instructions in the below?
 
[URL]

View 1 Replies View Related

Cisco :: Experiences With Issu On 7ks

Sep 8, 2012

Currently running 4.2.4(way older code) needing to upgrade to 5.1.6. Reading over the documentation on Cisco's site and some blog posts it seems like a painless upgrade without skipping a beat. But like always I am sure there are issues. I would love to test it out on a rack of some sort somewhere but the problem is with the 7ks after the line cards and sups there pretty expensive for a lab.

View 4 Replies View Related

Cisco Switching/Routing :: Upgrade 6509-E Ios Image?

Jan 9, 2013

I am going to upgrade the IOS image on 6509-E SUP 2T  from 15.1 to s2t54-adventerprisek9-mz.SPA.150-1.SY3.bin switch and i would like to know whether i would need to upgrade the boot loader image as well.

View 4 Replies View Related

Cisco Switching/Routing :: 6509 SSO Redundancy IOS Upgrade

Sep 9, 2012

I have a 6509 switch with SSO Redundancy (STANDBY HOT) with IOS ver 12.2(17d)SXB11, RELEASE SOFTWARE (fc1) (c6k222-jk9sv-mz.122-17d.SXB11.bin). I need to upgrade the IOS on this switch.I have 512MB Memory on the switch and 40144896 bytes free on Disk0.which IOS is the latest version to upgrade and also give me some hints for IOS upgrade on this switch?

View 7 Replies View Related

Cisco Switching/Routing :: 6509 Sup Engine 32 IOS Upgrade Via USB

May 14, 2013

I would like to find out how to upgrade SUP engine 32 via USB port as I've never did IOS upgrade on a SUP engine via USB before

View 5 Replies View Related

Cisco Switching/Routing :: IOS Upgrade For VSS 6509 Switches

Nov 19, 2012

I have 2 6509 switches configured with VSS.As per advised my managment I have to enable SSH but it is not available existing IOS which is "s72033-ipbase-z.122-33.SXI3.bin". SSH available in "s72033-ipbasek9-mz.122-33.SXI10".
 
upgrade the IOS with VSS configured switches.

View 9 Replies View Related

Cisco Wireless :: 6509 / WiSM1 Upgrade To WiSM2?

Apr 5, 2012

My company has been contracted to upgrade the 2 WiSM1 modules on a 6509 for a customer.  The hardware isn't changing but the software is being upgraded to WiSM2.  The cutsomer has HUNDREDS of AP's and dozens of VLANs and subnets (large municipality and school district).
 
Cisco SE's have been pushing the customer to purchase the WCS 7 software (they've been managing these Controllers independantly) stating there is no mechanism to upgrade WiSM1 configs to WiSM2.  I am vaguely familiar with the cisco controllers but have little WiSM experience. So i feel like i'm working without a net here.
 
So,
 
1) Any way to migrate from 1 to 2 without the WCS and without having to reinvent the wheel?
 
2)  How does the WCS make this transition easier?  What does it do to the WiSM1 configs to make them WiSM2 compatable? 

View 21 Replies View Related

Cisco Switching/Routing :: 6509 Supervisor IOS Upgrade

Oct 16, 2012

We are trying to upgrade the IOS on one of our 6509 switches. We have two 720 10GE supervisors running in SSO. Our procedure is reload the standby supervisor with the new IOS. We understand that you can only use one console connection when in RPR mode so we rely on the active supervisor giving us information that the standby unit is up and running.
 
The problem we have is that when we do a "show Module" on the switch the online diagnostics for the standby supervisor comes back us unknown. [code] We believe the active supervisor can see the standby supervisor because when we save the configuration we get a message saying that the config is sync'd with the standby router. We have a TAC case raised to investigate. We are upgrading from 12.2(33) SXI1 to 12.2(33) SXJ3

View 1 Replies View Related

Cisco Switching/Routing :: 6509-E VSS Will Upgrade Rewrite The Configuration

Jan 22, 2013

I am planning on upgrading my 6509s to use VSS within the next few weeks.  I have checked all of the hardware and software prerequisites, and we are good to go from that perspective.I do have more of a procedural question- my switches are already configured and in production, VLANs, HSRP (3 IP addresses per VLAN- 1 per switch plus virtual IP), etc.  Does the VSS upgrade take all of this into account and rewrite the configuration correctly, or should I plan on redoing the entire config for the switches after the upgrade?

View 6 Replies View Related

Cisco Switching/Routing :: 6509 Supervisor Upgrade With FWSM?

Oct 8, 2012

We are planning to upgrade the IOS on our two 6509E supervisors in the next few weeks. We currently run IOS 12.2(33) SXI1 and are upgrading to 12.2(33) SXJ3. At the moment the two supervisors are in SSO mode and after reading many articles it says that when the images are different on the two supervisors they are in RPR mode. When you then reload the active supervisor it will reboot all the line cards.
 
1. Is above correct? Will my line card reload?

2. We also have a FWSM installed, When/If the line cards are rebooted does the FWSM also reboot?

View 1 Replies View Related

Cisco WAN :: Cat 6500 IOS Upgrade - Installing Secondary SUP720 In 6509-E

Nov 21, 2011

I will be installing a secondary SUP720 in a 6509-E and will be upgrading the IOS on the existing SUP which is on  122-18.SXF6. I've read that this release has passed End of Critical Maintenance earlier this you. I thinking of upgrading the IOS to 12.2.33-SXJ1(ED) or 12.2.33-SXI8(ED) (possible more stable), but i'm not sure if i need any step upgrades from the current version. The SUP meets the required hardware specs and I will also be upgrading the ROMMON to 12.2(17r)SX7 first.
 
I have alot of experience upgrading IOS on routers and switches, but i just need to now if there are any gotchas that i need to know for the upgrade on the SUP.
 
The other issue is i don't believe the current IOS has been installed, are there any issue running on an IOS not installed. Patching is not available since the system is not running from an installed image. To install please use the "install file" command.

View 3 Replies View Related

Cisco Switching/Routing :: Upgrade SUP2 To SUP32 On 6509?

Sep 18, 2012

I am going to upgarde SUP2 to SUP32 on my 6509 by next week. right now I have 2 SUPs on the 6509 in redundant mode.

View 5 Replies View Related

Cisco Switching/Routing :: Upgrade 6509-Chassis In VSS-Environment?

May 1, 2013

we have some pairs of 6509-VSS, which partially have old (no more officially supported) 6509-Chassis.All linecards in the VSS are the same (Sup 720-10GE-3C, 67XX).
 
We now bought some new 6509-E-Chassis and want to change the old chassis by the new ones in a ISSU manner, that means:
 
1. putting the partner, which chassis changes, in redundancy mode, switch it off, exchange chassis (old "Catalyst 6509", new "Catalyst 6509-E")

2. inserting the line-cards exactly in the same slots and connecting all cables

3. switch on the new chassis, witing to come up in VSS
 
I'm not sure of having to set the switch number for VSS (is that in the Sup?; configuration? or part of the chassis-memory?)
 
I've looked up cisco for some hints, but don't found anything.

View 5 Replies View Related

Cisco Switching/Routing :: 6509 Upgrade To 12.2(33)SXI10 And ROMmon?

Dec 12, 2012

I have ROM MON version 12.2(17r)S2 and I am trying to determine if I need to chnage this to 12.2(17r)SX7. It does not appear I need to  with the upgrade to 12.2(33)SXI10. Is this correct?

View 1 Replies View Related

Cisco Switching/Routing :: 6509 / Sup2 To Sup32 Upgrade?

Oct 7, 2012

I need to upgrade 2xsup2 module to 2xsup32 on my cisco 6509. I just found out that I can not have the CISCO WS-X6500-SFM(Cisco Switch Fabric Module switch) with Sup32 and I have to remove 2 xCISCO WS-X6500-SFM2 modules from the switch.I am using this switch as a access switch and most of the ports are 100Mbps.
 
let me know if the upgrade would be safe or not as far as the bandwidth?

View 2 Replies View Related

Cisco Switching/Routing :: 6509 - Upgrade Sup720 To Sup2T In VSS Cluster

Jun 21, 2012

I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
 
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).

View 9 Replies View Related

Cisco Switching/Routing :: Upgrading IOS On Cat6500 Using ISSU

Jun 4, 2012

I am planning to upgrade my cat6500 using ISSU but can not find my doc to follow yet.

View 1 Replies View Related

Cisco Switching/Routing :: ISSU Process On VSS 1440

Feb 24, 2009

We are following the ISSU process for upgading a VSS 1440, using the documentation here: URL
 
After copying image onto both supervisors, when the command:

issu loadversion sup-bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI.bin is run we get the following error:
 
% CV [ bootdisk:s72033-advipservicesk9_wan-mz.122-33.SXI.bin ] must be named first in BOOT [ bootdisk:s72033-adventerprisek9_wan-mz.122-33.SXI.bin ]
 
The advipservice image is the one running, and the adventerprise is the one we are trying to upgrade to.

View 9 Replies View Related

Cisco WAN :: Upgrade Sup720 6509 Chassis - Configure Sup2T Management Ports?

Jul 1, 2012

We've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?

View 1 Replies View Related

Cisco Switching/Routing :: 6509 (HA) And FWSM (active / Standby) System Upgrade?

Sep 30, 2012

I have 2 6509 chasis with one SUP720-3B in each and current IOS is s72033-ipservicesk9_wan-mz.122-18.SXF4 and 2 FWSM with version is 3.3.1 I need to upgrade FWSM system software to 4.1, after checking FWSM 4.1 release notes, I thought of upgrading IOS to latest version  to 12.2(33)SXJ.I got new 2 CF of 512MB and downloaded the new IOS on them and need to upgrade 6509 IOS first to meet the requirement for FWSM upgrade.

View 1 Replies View Related

Cisco Switching/Routing :: Nexus 7010 Dual Sup ISSU

Aug 7, 2012

I have to upgrade a Nexus 7010 with dual Sup engines from 4.2(4) to 5.2 and am hoping it could be an ISSU. We are fine with an outage window.To upgrade from 4.2(4) to 5.2(5) I'll have to do a multi hop upgrade from 4.2(4) - 4.2(6) - 5.2(5) and each hop would take 40-60 minutes.do I spend 40-60 minutes for each hop, or just do a disruptive upgrade straight from 4.2(4) to 5.2(5)? Like I said, we are fine with an outage window.

View 2 Replies View Related

Cisco Switching/Routing :: Nexus 5548 - Can't Utilize ISSU

Jan 21, 2013

I need to upgrade the code on our two Nexus 5548's in order to facilitate the installation of a few FEX's, but due to the fact that seemingly all of my port-channels are in the STP DESG forwarding state, an ISSU upgrade is not possible. Everything connected directly to our 5548's are utilizing VPC's, including an HP Blade chassis, and several Netapp devices. If I follow the normal upgrade route, should I experience an outage, or should the secondary switch just continue passing traffic?

View 1 Replies View Related

Cisco Switching/Routing :: 6500 ISSU Process Is In Progress

Apr 15, 2013

We are looking to upgrade the version of IOS on the 6500s this evening and in preparation i've dowloaded the image to sup-bootdisk.  However when trying to update the boot path as follows I see the following error: [code] Why are we seeing this message when the router is not doing anything with ISSU?

View 3 Replies View Related

Cisco Switching/Routing :: N55K - ISSU And Bridge Assurance

Jan 14, 2012

In preparing for an upcoming upgrade of our serverswitches (N7K and N55K), I've run into a wellknown issue with ISSU and Bridge Assurance, where ISSU is not supported when, among other, BA is enabled.
 
My topology is quite simple (see attatched jpg). A pair of N7K's as distributionlayer switches running in vPC mode with BA between them. The N55K's are dualhomed across the two N7K's through vPC, but each N55K operate indvidually, that is vPC is not running between them. The jpg shows a simplified topology, but I have several N55K's attached.
 
During the deployment of this network, we enabled BA downstream towards the N55K. In hindsight, maybe I could have excluded this option, but currently it's in operation and is also hindering me in doing ISSU on my N55K's. Now, the easy solution would be to simply revert to normal span-type mode and since the N55K is running LaCP upstream towards the N7K's, we've managed to stay clear of STP's shortcomings, so I believe I'm good even without BA.
 
Unfortunately, I don't have sufficient equipment at my disposal to set up a lab and test the impact of disabling BA between the N7Ks and N55Ks in a running enviroment. And since our server/application enviroment is somewhat fragile (that's putting it mildly), I'm trying to come up with an educated guess as to what impact to expect, if I concurrently (or as close as a manual intervention can get) re-configure the two ends of the channel to use span-type normal. I would expect the upstream port on the N55K (channel-port) to temporarily be suspended and having to go through the usual rstp cycle on both ends before coming operational again.

View 2 Replies View Related

Cisco Switching/Routing :: 3750 / 6509 - Upgrade Core Switch Without Disrupting Network?

Feb 2, 2013

I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.

View 7 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved