is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
View 5 RepliesFacing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedI am using cisco c3660 to act as Terminal Server for the communication of production machines in my company, recently there is a communication lost issue happen and its due to physical cable unplug from the machine. to troubleshoot for this issues i have to physically go inside my production area to check on it, as i understand from vendor we can check on the physical machine to see whether the LED light on the module is green or not, but in case of need to troubleshoot at night time, its time consuming as i need to travel back to company. is there any command that i can issue in the router c3660 to check on the physical connection between c3660 router and the production machine? the IOS version is IOS (tm) 3600 Software (C3660-I-M), Version 12.1(4)
View 3 Replies View RelatedAny command similar to sup720 "show tcam counters" It doesn't work on Sup2t.....
View 2 Replies View RelatedWe have Nexus 7K recently installed few months back with 2 Sup (Slot 5 & Slot 6).Recently recevied mesaanges in monitoring servervia SNMP:Alarm : active unit removal caused an auto SWACT However, when checked there are no recent logs which may be linked to this alarm. The show redundancy command output shows that Sup in slot 5 is active which in slot 6 is Hot Standby.
View 1 Replies View RelatedI enabled the "no service password-recovery" command on my C2960 switch. All seems to work as discribed. Only issue I have is --- which show command is used to reveal if the password-recovery feature is enabled of disabled as the command doesn't show up in the running config after you enable it ?
NOTE: The command does show up in the C2960 switch in config t mode (unlike the IOS router 2800 series), but doesn't show up in the running-config after you enable or disable it.
On the 2800 series routers (latest IOS) in config t mode the command does not show up but if you type "no service passowrd-recovery" the command function correctly and it does list it in the running configuration.
tell me if there is an equivalent command to Show int Summary on the Nexus 7000?
eg
MYCISCOSW01#show int summary
*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle count
[code]....
I find it a useful command on the 6500 to spot high traffic flows.
know Cisco IOS command, how to show when Catalyst 2960 was shut down (power off)?
View 2 Replies View RelatedI have a 2960S connected to an RSP 2300. The 2960S is currently running off of the RPS, and I would like to switch it back to the internal power supply. Can I just run "power supply 1 on"? Will this cause the switch to reboot? Also I am concerned because when I do a show env power it shows: [code]
Is it normal for the internal power supply to show Unavail when running off RPS?
I have been working on some Catalyst 3750's running 12.2(55)SE6 and hit an issue with CEF load-balancing over multiple equal-cost paths. Anyway this issue is now solved but it introduced me to the command 'show platform forward' - this shows you how the forwarding of a packet would be done via hardware cef (as opposed to the command 'sho ip cef exact-route' command that only shows the software cef path). Anyway I tried the command on a 3560G running 15.0(2)SE and it crashes the switch. I tried it a couple of times and verified that the MAC & IP addresses were exactly right in the command and each time the switch crashes. I have extracted the relevant bits from the crashinfo and attached them.
View 3 Replies View RelatedWhat is the exact command in restoring the running-config on a Nexus 7010. Is it the same command / procedure as the Cisco IOS?
View 3 Replies View RelatedOn a 3750 you can do a show platform port-asic stats drop command. Is there a corresponding command for 6500 chassis?
View 7 Replies View RelatedI am looking to replace the active supervisor (S720-10G) on our 6509E running in SSO mode. The new module already has the same IOs version as the standby supervisor.Once I have swapped the module how do I know that the config has sync'd correctly other than checking the logs? Is it a case of looking at the "Redundancy Mode (Operational)" state and ensuring is says SSO?Also, is there a command that will force a config-sync if it is running in a mode other than SSO?
View 1 Replies View Relatedhow to show all the module on the ASR 1004?
View 4 Replies View RelatedI'm moving this [ URL], discussion here because I feel I will get a quicker response. In a nutshell the setup is as below:
ASR1004=={ GRE }==C7206
I need to run layer 2 services between the 2 without mpls support from the service provider. Unfortunately there is no specific detail on getting EoMPLSoGRE up and running. I have the GRE tunnel working and I have mpls forced to my loop backs and the x connect configured on the 2 router interfaces. However the mpls forwarding table on the 7206 shows the outgoing interface is 'none' and I cannot pass any traffic across.
7206>sh mpls forwarding-table Local Outgoing Prefix Bytes tag Outgoing Next Hop tag tag or VC or Tu [code]...
On the ASR it looks fine: asr>sh mpls forwarding-table labels 201Local [code]...
On the Cisco forums, an example is shown for how to configure BVI and bridge-groups on an ASR1004 but the same command (bridge-group) is not available under the interface on our ASR routers. We are running version of code: asr1000rp1-advipservicesk9.03.06.00.S.152-2.S.bin
View 1 Replies View RelatedI am in the process of staging a couple of two new Cisco ASR 1004's which are located at two locations with a WAN link in between. I need to set up connectivity between servers plugged directly into each ASR router across the WAN link. The ASR has 16 gig interfaces (gi0/0/0 - gi0/0/7 and gi0/1/0 - gi 0/1/7), and a management interface (gi0). I have connected the WAN link to gi0/0/0 and put an ip address on it. The servers will be plugged into the remaining gig interfaces. I tried to create an SVI (vlan interface) in an attempt to create an L3 interface to support routing to these servers but these routers don't allow SVI's to be created. how to put these server connected ports on a vlan and to create an L3 interface to provide routing to them?
View 1 Replies View Relatedon the asr 1004 , how test and check if the SFP receive power or signal from the MUX? any command to do that?
View 3 Replies View RelatedWe bought a pair of ASR 1004 to be installed at Primar & Secondary data center and one thing is to run OTV over it, but to do that, I have to extend multiple VLANs from my Core (Pair of Nexus 7010s) connected directly to the ASR is Primary Data center, I looked at some documents but didn't get a good idea about it, extend multiple VLANs from Nexus switch to an ASR.
View 2 Replies View RelatedI have configured a vlan interface on a 3750 switch. there is aprox 4Mb active traffic flowing through the interface, but when I do a "show interface vlan (vlanid)" the output show zero bits in and zero bits out. Its a typical L3 config with one IP on the vllan interface acting as the gateway for the VLAN devices. Is this a normal behaviur ? and if so is there any way to get the traffic in/out stats. The end PC/devices are connected to this switch via an L2 TRUNK and I dont have access to the L2 switch on which the actual devices connect. so cant get the real time stats of those interfaces.
View 2 Replies View Relatedi have ADSL. modem:Meganet when i connect to internet from windows xp with making PPPOE connection everything is fine and when i do ipconfig i can see my IP. but when i connect directly from router then IPconfig show this only:
[code]...
I have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
View 2 Replies View RelatedLooking for a show command to display the actual physical Ram modules inside a 2911 router. I believe they come with 2x ram slots and I need to know if it has 1 ram stick or 2.show version displays the total amount of ram, but not if its 2x128 or 1x256 etc.This is also production gear so I cannot open it up and have a look until the scheduled downtime.
View 3 Replies View RelatedIs there a command that can show EVERYTHING that is configured on a router or switchSeems if you're looking to save enough information to completely swap out a device the run/start config isn't enough.Settings like VTP and MTU settings aren't shown in the config file ... there may be other configuration settings like thisAm I forced to just know to check those settings are is there a command that will show the running-config AND all these other settings that aren't in the config?
View 8 Replies View RelatedThe Cisco 887 doesn't support the show dsl command, what is the command that I need to use to display the speed my ADSL is operating at? On the Cisco 877 the command I use is show dsl int atm 0 but this doesn't work on the 887
View 4 Replies View RelatedI'm trying to troubleshoot one of our site today and can't seem to issue the show dsl interface command on a 1841 router. Does the same command is used for SHDSL or am I running with an IOS bug?
#sh dsl?
% Unrecognized command
#sh ver
Cisco IOS Software, 1841 Software (C1841-BROADBAND-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
Technical Support: {URL}
Compiled Wed 13-Aug-08 15:42 by prod_rel_team
#sh inv
NAME: "chassis", DESCR: "1841 chassis"
PID: CISCO1841 , VID: V05 , SN: FHK13212639
NAME: "WIC/HWIC 0", DESCR: "WAN Interface Card - ATM (With multi line G.SHDSL module)"
PID: WIC-1SHDSL-V3 , VID: V02 , SN: FOC132041KD
i have 10 stations, and i think one of them generated allot of traffic.maybe a virus sending spam.is there a command that can show my which station consume bandwidth?
View 3 Replies View RelatedMy customer has upgrade his 4506 from 6L-E to 7L-E 10GE.Ever since then if he run the command show dot1x interface gigabitEthernet x/x details some information are not been displayed (below are missing information)Is this intensional or do I need to kick this to TAC?
View 1 Replies View RelatedIs there a good reference in how to interpret the "show AP stats" command?
I have a new (online for 15 days) 1142 listed below. It is the first 802.11n AP I've deployed. The stat counters look bad [code] But I don't know how to put it all together to say "here are the stats, this is the problem". I see TxFrameCount, but no corresponding RxFrameCount, so it is hard to calibrate some of the errors. [code]
I am running windows 7 HP. We have about 10 devices in one office and 5 devices connected thru a VPN..... When i hooked everything up 4 weeks ago I could see all the devices in the main office and the remote office connected thru the VPN (In the Network Folder that lists everything connected). Now I only see like 4 device and they are all in the main office.
I did some research a couple weeks ago and found a command prompt that "refreshed" all the devices that were connected, but now They are gone again and I cannot remember the command prompt!
I am using ACS5.2 I want user to access the device with all necessary command like show run/ver/int/log… I try to set user privilege using Shell from 1 to 10 but show run doesn't work.
View 15 Replies View RelatedIn our company we use the ACS 5.and i have a small problem, what we need to do is.create a profile that will allow SHOW RUNNING CONFIG but not configure terminal.i am investigating and im a littel bit lost i have created a new group but i dont see any option to put permissions.
View 1 Replies View RelatedI'd like to know if there's a command I can run to turn off paging on my SF302 switch. So for example, when I run the "show logging" command on the CLI, I'd like to it return all the results instead of prompting me to hit space bar or enter.
View 3 Replies View Related