Cisco WAN :: ASR 1004 / C7206 - EoMPLSoGRE Up And Running
Jan 31, 2010
I'm moving this [ URL], discussion here because I feel I will get a quicker response. In a nutshell the setup is as below:
ASR1004=={ GRE }==C7206
I need to run layer 2 services between the 2 without mpls support from the service provider. Unfortunately there is no specific detail on getting EoMPLSoGRE up and running. I have the GRE tunnel working and I have mpls forced to my loop backs and the x connect configured on the 2 router interfaces. However the mpls forwarding table on the 7206 shows the outgoing interface is 'none' and I cannot pass any traffic across.
7206>sh mpls forwarding-table Local Outgoing Prefix Bytes tag Outgoing Next Hop tag tag or VC or Tu [code]...
On the ASR it looks fine: asr>sh mpls forwarding-table labels 201Local [code]...
View 3 Replies
ADVERTISEMENT
Aug 29, 2012
is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
View 5 Replies
View Related
Feb 1, 2011
I have a site which has been successfully running a multilink bundle of four T1 lines for about 6 months. The remote location is a C3825 router and the central location router is a C7206. I have access to both. A few weeks ago the multilink circuit started flapping and I was able to identify one of the four T1 lines as the culprit. When I shut down the interface for that one T1 line, the multilink circuit stops bouncing. As soon as I issue a "no shut" command on that fourth T1 interface, the multilink circuit starts flapping, ping commands start to time out and I have to shut it down again. The Telco has sent a technician to both locations and reported all tests run clean. Internal wiring from the NIU to the router has also tested fine. I've tried to move the T1 lines to different ports on both routers and the problem persists. [code]
View 9 Replies
View Related
Oct 25, 2010
ASR 1004, has a image, which is on the harddrive, not bootflash and we have no boot commands in the configuration…We are running the ROMMON version ‘15_01rs’ The ASR boots into Rommon, as it cannot find a image (as expected), as the configuration has no boot commands.Trying to TFTP or getting an IOS back into bootflash is proving problematic.Follow all TFTP commands..
rommon 1 > IP_ADDRESS=10.1.1.1
rommon 2 > IP_SUBNET_MASK=255.255.255.0
rommon 3 > DEFAULT_GATEWAY=10.1.1.1
rommon 4 > TFTP_SERVER=10.1.1.2
rommon 5 > TFTP_FILE=asr1000rp1-adventerprisek9.03.01.01.S.150-1.S1.bin
[code]....
View 5 Replies
View Related
Feb 14, 2012
how to show all the module on the ASR 1004?
View 4 Replies
View Related
Jun 2, 2013
I did a software upgrade in ASR 1004.Before, i validate the butes quenatity, and verify the /md5 and SHA1 checksum, and both appear ok. [code]
View 1 Replies
View Related
Jun 12, 2011
we are going to build L2L IPSEC VPN on ASR 1004 at our new datacenter edge. but i don't find any familiar CLI on my 1004. any special license,IOS-XE version or processor is required ? ASR1000-ESP10 is necessary ?
View 2 Replies
View Related
May 2, 2012
From PEC training - Cisco says to perform a proper ASR 1004 shutdown by executing 'reload' , then wait for bootstrap message to appear, then [before commencement of unpacking of the IOS] turn off the power switch. IS THIS ACCURATE. Anyone have any doc related to the recommended POWER DOWN process on the ASR 1004. We have a UPS cutover coming up and I want to be ready to power down and restart the new ASR 1004s we have - properly.
View 3 Replies
View Related
Jul 19, 2012
On the Cisco forums, an example is shown for how to configure BVI and bridge-groups on an ASR1004 but the same command (bridge-group) is not available under the interface on our ASR routers. We are running version of code: asr1000rp1-advipservicesk9.03.06.00.S.152-2.S.bin
View 1 Replies
View Related
Jul 19, 2012
I am in the process of staging a couple of two new Cisco ASR 1004's which are located at two locations with a WAN link in between. I need to set up connectivity between servers plugged directly into each ASR router across the WAN link. The ASR has 16 gig interfaces (gi0/0/0 - gi0/0/7 and gi0/1/0 - gi 0/1/7), and a management interface (gi0). I have connected the WAN link to gi0/0/0 and put an ip address on it. The servers will be plugged into the remaining gig interfaces. I tried to create an SVI (vlan interface) in an attempt to create an L3 interface to support routing to these servers but these routers don't allow SVI's to be created. how to put these server connected ports on a vlan and to create an L3 interface to provide routing to them?
View 1 Replies
View Related
Jun 28, 2011
i just configued a L2L tunnel between ASA 5510 and ASR 1004. tunnel is up but got serious packet lost (more than 70%) and isakmp always up-down intermittently.i compared parameters on both sides again and again but no luck. [code]
View 4 Replies
View Related
Nov 29, 2012
on the asr 1004 , how test and check if the SFP receive power or signal from the MUX? any command to do that?
View 3 Replies
View Related
Jun 5, 2011
I bought a Prolink Wireless Router WGR1004 and I have problem connecting it with internet. My windows able to detect and connect to the Wireless connection but the internet browser cannot display any webpage. I have a Linksys WB300 ADSL Modem when wired to my pc it pings IP 192.168.1.3 , default gateway 192.168.1.1 My connection to Wireless pings IP 192.168.1.2, default gateway 192.168.1.1ADSL phone cable connected to my modem and Ethernet cable linked from Modem to Internet Port of Wireless router. Settings in Network Connections=>properties=>TCP/IP=>Obtain an IP address automatically and obtain DNS Server address automatically. Web browser connections settings=>Internet Options=>Lan settings=>Automatic detect settingsRouter Configuration=>Lan IP address is 192.168.1.254 Internet IP address is 192.168.1.2, Security and SSID are working properly. The problem is my web browser cannot display webpage.
View 1 Replies
View Related
Mar 6, 2013
We bought a pair of ASR 1004 to be installed at Primar & Secondary data center and one thing is to run OTV over it, but to do that, I have to extend multiple VLANs from my Core (Pair of Nexus 7010s) connected directly to the ASR is Primary Data center, I looked at some documents but didn't get a good idea about it, extend multiple VLANs from Nexus switch to an ASR.
View 2 Replies
View Related
Jun 11, 2013
I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies
View Related
May 7, 2013
I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies
View Related
Sep 11, 2011
we are experiencing performance issues on ASR 1004 with ZBF as our campus edge router.Symptoms:
- sending small packets from inside zone to outside zone, for example UDP packets without payload
- this way I can generate up to 150.000 pps traffic (testing with packeth software, but we have had a real example with some kind of worm/virus)
- CPU load is about 1% (yes one!) to 2% all time !! (weird)
- ASR response to pings rises very quickly up to 5 seconds which makes box unusable dropping everything what goes through ZBF (so internet connection is gone)
- if I do the ping directly from box, it seems to work fine (no rules from self to outside zone in ZBF)
- if I remove interfaces from inside and outside zone (so disabling ZBF) and do the test again, ASR response goes from normal (0.2ms) up to 2ms (still sending 150.000 pps) and everything seems to work fine)
According to Cisco Datasheets: routing, Qos, Zbf ... on ASR 1000 with RP1, ESP10 should be done in hardware with up to 17.000.000 pps performance.
View 5 Replies
View Related
Mar 5, 2013
I have ordered RP2 and it will be having 8GB default memory. What is the difference between memory & Physical memory?Since I am able to see only 4GB memory in my ASR 1004. [code]
View 1 Replies
View Related
Apr 19, 2011
I'm not sure how to tell if I'm running ssh version 1 or ssh version 2, or both.I thought a show run would show a line like, "ip ssh version 2" or "no ip ssh version 1", but I don't see these anywhere.
View 4 Replies
View Related
Jan 21, 2013
connecting PRI to BRI interface on ISDN. I have all this information provided by the TELCO and i have configured it but due to some reason i am not able to connect them. I have given the questions with answers provided by the TELCO. I am also providing the running configuration of the PRI interface and also the error message i am getting when trying to test call itself.
1. Is the PBX designed for Pre-National or NI-2 protocol? -
Protocol using C7MATL
2. Are there any DID station numbers that your CPE cannot accept? -
No
(i.e. 0 or 9 in the 4th position)
3. Which carriers will be your choices for your PIC and LPIC? -
Carrier using DChannel
[code]....
View 2 Replies
View Related
Apr 25, 2013
I am running LMS 4.1on a VM, it runs very slow, what specs my vm should be running to support this application?
View 2 Replies
View Related
Mar 5, 2013
I can't seem to get my DIR-655 up and running again.I had a DLINK DIR-655 hooked up via RJ-45 cable(s) to my AT&T U-Verse 3800HGV-B Gateway. The DIR-655 was serving as a wireless connection for my laptops and also as a wired networked all-in-one printer that was plugged into it.The Ethernet (RJ-45 cable) traveled from the gateway, through a 4-port switch, and then to the Internet (WAN) jack on the back of the DIR-655.There's a couple of wire- connected computers connected via that switch in between that's why it's there. At the DIR-655 end I had an HP Photo Premium AIO printer (Model: 309A) connected by wire; and of course, the two laptops would connect via that unit too. The laptops are WinXP and Win7.Everything worked fine... BUT, the upstairs iMac and a downstairs home office XP machine couldn't see the networked printer for some reason. That reason (apparently) is that the DIR-655 is part of a "separate network" or something.Well, long story short - I tried to adjust the settings on the DIR-655 but that didn't work and then I tried to go back, but that didn't work. So then I decided to just start from scratch to re-setup the whole thing but NOW I can't even access the router via a browser at url...
View 14 Replies
View Related
Jan 18, 2013
Platform: LMS 3.2.1 with RME 4.3.2 on Windows 2003.I'm having a problem with several devices that were backing up fine until this week - suddenly they aren't backing up their running configurations, but RME is fetching their startup configurations fine and VTP backups are fine. At first I thought it might be timeouts, so I used inline edit to incease the telnet timeout for a device to 180s. However, the job fails well within this time period (debug shows on i/o error?). My order of protocols is SSH, Telnet, TFTP. I took a stab in the dark that this suggested a database problem so I picked one at random and deleted it from DCR, and readded it and it worked. However, for the other 48 devices affected it did not.
I'm wondering if I need to do anything to the RME database to get things back to where they were? Do I need to reinitialize the RME database, and if I do that what do I lose? [code]
View 2 Replies
View Related
Feb 5, 2013
we have two ACS 5.0.4.46.1 and since a few weeks, it reports the following error:
I stopped and restarted ACS, reconfigured the repository, reconfigured the backup and so on. I even rebooted the ACS but it sill has this problem. I can see "Please contact TAC..." but I first wanted to ask the community.
View 7 Replies
View Related
May 12, 2010
I hardly try to get WDS running with two WRVS4400N v2.The manual (and the web interface) says: "Note: The WDS feature allows WRVS4400N to connect with up to 3 wireless repeaters that can be either WRVS4400N or WAP200." But I wasn't successful by now in getting it working..What I've done so far:
- Setup the primary WRVS as Gateway, WAN through Modem, LAN and WLAN using WPA2 Personal Mixed, DHCP
- works perfect
- Setup the second WRVS as Router using the same WLAN settings, no WAN and no DHCP
- Enabling WDS on both WRVS, giving each the MAC address of the other
- no connection to LAN or WAN through the second WRVS
I really need the second WRVS act like a bridge. Since the manual is saying that I can connect both devices through WDS I bought two of them. On the other hand I've now read somewhere in the community, that this isn't possible with two WRVS (?)
View 6 Replies
View Related
Sep 23, 2012
I have a particular site that is causing me trouble, this site is connected in a back to back configuration using 2811 at CO and 2621XM at CPE. The CO end is also the CO for 3 other sites so has a total of 4 wics installed (WIC-1SHDSL-v2), these other sites also have 2621XMs for the CPE.
The problem i am getting is when one site in particular transfers large files to/from client machines, the CPU on the 2811 jumps to 99%:
CPU utilization for five seconds: 99%/98%; one minute: 26%;
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
11 12881868 37249378 345 0.49% 0.50% 0.51% 0 ARP Input
54 8548592 30375358 281 0.40% 0.45% 0.41% 0 XDSL BACKGROUND
[Code]......
View 2 Replies
View Related
Jul 16, 2012
we have a situation that we need to run ASA as a router. we have two sites connected via a private p2p link, we also have ASA5520 in each site and we have L2L IPsec tunnel over Internet, we want to failover to IPsec over Internet pipe in case p2p link fails. With BFD/OSPF this design works at L3 level. But we have problem to keep existing TCP connections when failover happens, the reason is, I believe, when ASA sees a new connection coming in without seeing SYNC flag in the packet, it will not create a connection entry and drop the packet unless a new connection is initiated from either side. So my question is, is there anyway I can configure ASA to behave more like a L3 device, ideally to turn off L4 checking for IPsec traffic?
View 4 Replies
View Related
Jan 17, 2011
I have installed WCS 7.0 now i have installed Navigator on WCS server.Installation is completed.but when I check the status of WCS, it says "healthmonitor running with errors"any one knows what could be the problem and how much will that effect on WCS performance?
View 6 Replies
View Related
Aug 28, 2012
I have an existing 1800 router that is using NAT and VPN to HQ. I now have a new ISP provider and so now i need to chane the Fastethernet1 IP address. I know how to do that but what else do I need to change to make everything continue to work?
View 10 Replies
View Related
Apr 10, 2012
Im planning to install a WAN Switch on our network basically this WAN switch will be the core WAN switch in our WAN segments where all WAN connections coming in and will use EBGP peering to every CE WAN router.
is Advanced BGP supporeted in WS-C3750X-24T-S?
View 5 Replies
View Related
May 26, 2013
I was going through the release notes on cisco website of ASA 8.4.6 and ASDM 7.1.3 but I just can not find a definitely answer: if ASDM 7.1.3 can run with 8.4.6?
View 2 Replies
View Related
May 15, 2012
I'm having an issue configuring NAT on an ASA running 8.3. 've managed to configure NAT from the Inside interface to the DMZ, using PAT, so that the traffic is hidden behind the IP of the DMZ interface. This seems to work ok.
object network obj_any-18
subnet 0.0.0.0 0.0.0.0
object network obj_any-18
nat (inside,dmz1.005) dynamic interface
The problem I have is when I try to configure a rule for traffic that originates in the DMZ back to the Inside. I can't seem to get any traffic to flow from the DMZ to the Inside, and sometimes I manage to stop traffic flowing in both directions!
What would be the best way to configure the return traffic from the DMZ to the Inside.
View 12 Replies
View Related
Dec 11, 2011
I have an ASA running 8.4(2) code.
I have been trying to get a VPN tunnel established between this device and a Checkpoint R70 firewall, but have been getting nowehere.
The settings are:
Encap: ESP
Encryption: AES256
Hash: SHA1
DH: Group 2 (1024)
Authentication: pre-share
lifetime: 1440 min / 4096000 KB
I can open the tunnel from the ASA to the Checkpoint, but the Checkpoint cannot open a tunnel with the ASA. It looked like the issue originally was the KB timout which was turned off on the Checkpoint side. They have since added that (4096000), but we are getting Phase2 failures.
How to create a tunnel between an ASA running 8.4(2) and a Checkpoint R70?
I am beginning to think that I have incompatible systems Is it a PFS issue? If so, how do I enable that in the policy section?
View 1 Replies
View Related
