I have ordered RP2 and it will be having 8GB default memory. What is the difference between memory & Physical memory?Since I am able to see only 4GB memory in my ASR 1004. [code]
View 1 Replieswhat is physical diffrance between switch and router?
View 1 Replies View RelatedWhat causes LMS 4.1 to have high memory utilization?
View 4 Replies View Relatedit is possible use 1 or 2 Gb memory with ASA 5505 or only 512 Mb ?
View 3 Replies View RelatedUpgrading the memory on an 1841. After inserting a 256MB/PC133/SDRAM/DIMM it would not post during the boot, hangs.If i take out the chip it works fine.The on-board memory is 128, so the 256 is the max it would take to a total of 384. According to the documentation this should work.The memory chip is a Transcend chip, basically Samsung.
View 2 Replies View RelatedI am doing the initial configuration on our ASA 5510 to use our Radius server just as our 3005 VPN Concentrator did. I can do the test connection inside the ASA with no problems, and when I authenticate using the Anyconnect client, it appears to authenticate fine, but then dumps the connection with an error stating there is not enough memory in he ASA to allow this connection, the error message is as follows:
Error Message %ASA-4-722004: Group group User user-name IP IP_address Error responding
to SVC connect request.
Explanation There is not enough memory to perform the action.
Recommended Action Purchase more memory, upgrade the device, or reduce the load on the device.
Can this really be the case with no connections active, a single user attempting to authenticate through Radius and an out-of-the-box ASA 5510?
The issue is when I am using PPTP the router seems to die, not every time but I would say about once a week now. I am the only PPTP user, simply using RDP. A few hours into an RDP session the PPTP connection drops and cannot be re-established, or quickvpn, nothing. Routing still works (somewhat, high latency) locally.
When I've checked the logs both times I see:
TimeEvent-TypeMessageSep 3 17:07:56 2012KernelOut of memory: Killed process 14354 (pppd). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 177 and children. Sep 3 17:07:56 2012KernelOut of memory: Killed process 14367 (sh). Sep 3 17:07:56 2012KernelOut of Memory: Kill process 14354 (pppd) score 234 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14330 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14329 (pptpctrl) score 134 and children. Sep 3 16:46:41 2012KernelOut of memory: Killed process 14324 (pppd). Sep 3 16:46:41 2012KernelOut of Memory: Kill process 14324 (pppd) score 177 and children. Sep 3 16:46:40 2012KernelOut of memory: Killed process 14328 (sh). Sep 3 16:46:40 2012KernelOut of Memory: Kill process 14324 (pppd) score 234 and children. Sep 3 15:36:15 2012KernelOut of memory: Killed process 14187 (pppd). Sep 3
[code]....
We have recently purchased a brand new RV042G VPN router, set it up, and had it running for a while without issues.
Now that we are actually trying to use the VPN functionality, the router becomes unstable after a while, showing "out of memory" lines in the logs, and after a day or two the VPN stops working completely and the web interface becomes completely inaccessible.
This issue happens when using any sort of VPN that's supported by the router.
I've deployed many Cisco PIX 501 v6.3.3 either as normal firewalling feature and/or with VPN features enabled. I noticed in all my deployments, regardless if it's during peak hours or after office hours, the memory utilization is always consistent 11MB utilized over the total of 16MB(memory default size).
View 3 Replies View RelatedI want to upgrade my IOS on an 871W. In order to do this I need to upgrade the memory. I have found that I need the MEM870-32F (Am I correct?).
As in here: {URL}. So if I follow these instructions: {URL}. Is that all there is to it?
we have some unusual issue when our core 3825 series router dealing with NAT !first off to offload traffic we have two router one 3825 and other 2821 configured to support GLBP .
interface GigabitEthernet0/0
ip address a.b.c.d 255.255.255.0
ip nat outside
ip virtual-reassembly
[Code]....
The problem is router hangs out , intenet users suffer slowness , criticle service like telnet doesnt work . the only solution i found is a reload ,not to mention this is core router sitting on campus network edge . and servicing around 1000 users !! approx assuming all users have using internet at same time .
how to check , if memory is not sufficient ?further if any users using utorrent or any thing like that , does it make enormous no of connections form same pc ?
is their any licence requird for IOS IPS ?i prefer to turn this feature on to kill torrents connections ? but i fear crashing of router as no of users are huge !any know bug with glbp , nat with ip voice image C3825-IPVOICE-M VERSION 12.4(24) T4 ???
To have a management tool polling by SNMP some information like CPU load and memory load, I tried to find out the OID.The supervisory card is a WS-X45-SUP7-E with a dual core CPU and 2G of memory.IOS is IOS-XE 3.2.2
Does any OID or nagios template already for the new card ? The Nagios template I use for others switches do not get the good field
My son ran some program that he didn't know what he was doing and now there is no Network access. As far as I know this is what caused the problem, but I'm not certain. When I tried to reinstall the drivers an errors pops up stating that the drivers couldn't be installed due to "Invalid Access To Memory Location". The networking card is an Intel 82566DC-2 Gigabit Network Connection Adapter. The Networking card is part of the Motherboard. I have the original drivers but they will not install due to the "Invalid Access To Memory Location". Anyhow my son went and bought a new networking card, and it gives the exact same error. I tried uninstalling the networking card in the device manager, but when the hardware is reinstalled, and the drivers are about to install it gives the same error. computer is a Dell XPS 420 with 6 gigs of RAM, an Intel Core 2 Quad CPU Q6600@2.40GHz Also in the Device Manager everything under the Heading Network Adapters has a Yellow Triangle with an Exclamation mark in it. I know that this means that there is an error somewhere. I also want to add that when I checked the Netgear GA311 Network adapter card (this is the new card that my son bought)in the Device Manager it says This Device is not working properly because windows cannot load the drivers required for this device (code 31).
View 9 Replies View RelatedI wanted to know how many sodium memory slots the 1841 Routers have so i can upgrade to more then 128mb of DRAMI want ideally 256+on the Cisco website in the diagrams they dont say if it has 1 or 2 slots
View 8 Replies View RelatedI'm working on a distribution config for some routers with a software IPS. The problem I'm running into is the final [confirm] during setup. Is there any way to disable confirm messages in IOS?
View 1 Replies View RelatedCisco 3845 router (256RAM / 64Flash), increases the cpu utilization upto 70~80 percent, during the time of high utilization, I am unable to run show command on router.The configuration is simple, this is connected with two internet links (24Mbps and 8Mbps) and its about 600~700 users are using internet.show version, show memory and show process cpu outputs are attached here.
View 7 Replies View RelatedAny known problem with the DRAM on 2800 routers? Over the past few months we have had four 2800s fail to reboot after power off/on and in all cases this was due to faulty DRAM. All four routers had been working fine for months with no problems and only failed after being rebooted. They all failed when trying to load the IOS into memory and therefore all got stuck in rom mon. The compact flash cards were all ok as a working 2800 booted up using the flash from the faulty routers. I haven't seen a field notice so are we just unlucky here?
View 0 Replies View Relatedi know that Sup720-3BXL has been used the SDRAM.but i don't know that which of memory? using of ECC or plain memory?if use the plain SDRAM, how can prevent to parity error?
View 1 Replies View RelatedNeed this file to erase my flash memory?
View 2 Replies View RelatedAs soon as I connected my ASR 1002s to the Internet and digested the Internet BGP table, I began receiving this message. I’ve google’d and turned up nothing so far. I assume I need to allocate more memory to this process.
%PLATFORM-4-ELEMENT_WARNING: R0/0: smand: ESP/0: Committed Memory value 312% exceeds warning level 310%
Here's a sh mem:
#sh mem Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)Processor 3008A008 1758530508 647878488 1110652020 1110104020 1109994164lsmpi_io 98FEB1D0 6295088 6294120 968 968 968
I have an ASA that is logging the message %ASA-3-321007: system is low on free memory blocks of size 2048. I ran the "show blocks" command and the "Cnt" value for the 2048 blocks is 0. How do I reclaim these blocks and what are they used for?
View 1 Replies View RelatedI am trying to get experience with 8.4 code on my 5505. I purchased a Cisco 512MB memory upgrade and installed it. It booted up once and I thought I was ok. I then looked down and noticed that all lights were blinking on the front panel and I had no console access.
[code]...
Trying to figure out if I can upgrade this flexwan to 256MB and not sure is the card below already has 256MB total or 1 64MB per PA equaling 128MB total.
View 1 Replies View RelatedWhat kind of DRAM memory compatible with 3845?
View 4 Replies View RelatedWe have a customer that has a ASA 5525-x reporting only 4g flash memory rather than 8g has any 4g version of the 5525 or is the IOS reporting incorrectly the size, as it seems to be embedded on these units as a USB disk internal.
View 4 Replies View RelatedCurrently I have C2801 with 256MB of memory and 64MB of flash. I want to upgrade it to 384MB / 128MB.Do I need to get MEM2801-256D or I can use any PC133 SDRAM (144PIN) for memory? 384 is maximum I can install? Do I need to get MEM1800-128CF or I can use any compant flash card? 128MB is maximum I can install? (I saw 256MB flash on for C2801)
View 10 Replies View RelatedI was looking at my CISCO ASA 5520 and i found something really strange
ciscoasa/VPN-context# sh mem detail
Used memory: 4259249568 bytes (793%)
------------- ----------------
Total memory: 536870912 bytes (100%)
but when I look at the system context this is what I see
ciscoasa# sh mem
Free memory: 170829000 bytes (32%)
Used memory: 366041912 bytes (68%)
------------- ----------------
Total memory: 536870912 bytes (100%)
As far as I know the ASA is working good.
Info of the device
Hardware: ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Just want to check with you about memory utilization on the Asa 5510 ..
Free memory: 19%
Used Memory: 81%
Is this normal? Because we hade a problem this morning and the memory was at 100%..
Device Manager version 6.1(5) 57
Hardware: ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
We have a Cisco SA520 Router (Firmware 2.1.18)We are only using this for about 1 month now. Router seems ok its justI am worried about the Memory utilization which reach to 62% (144/234 MB)Is this something to worry about?How can I utilize this by lowering down the usage?
View 3 Replies View RelatedWe have a couple of 6500 series switches and have 3 BGP peerings to each. The 6500 series switches are loaded with WS-SUP720-3B Supervisor Engine. I believe there is a limit to the number of IPv4 routes WS-SUP720-3B supports(256,000). We also have "soft-reconfiguration inbound" configured on the BGP peerings. Thus when I do a "show ip bgp A.B.C.D" it displays three routes from 3 BGP peers and it displays an additional 3 "received-only routes" which I think is due to the "soft-reconfiguration inbound" configuration. We currently filter inbound routes from the BGP peers to be between /0 and /27
We are now looking to add another 2 BGP peerings. I am not too sure if the WS-SUP720-3B will be able to handle all the BGP routes. Is this limit of 256,000 IPv4 routes due to Processor memory limitation or is it software related? Would removing the "soft-reconfiguration inbound" save me some memory ?
installing IOS for cisco 4503 e catalyst switch. The base ios image file has been deleted. Installing the ios and from where can I download the ios verison.The device has 2 10 Gig uplinks and I have access to console of the device.when i boot up the device it comes "rommom >"I do have tftp server and i have also configure the IP in fast ethternet mgmt port.
View 2 Replies View Relatedi just noticed that im getting some alloc memory errors with a flexwan card i have on a cisco 6513 on slot 5/1, however i can't seem to figure out how to get more information on this and if the issue is related to the flexwan module or the DS3 card itself. Not really sure how to view memory stats/errors for a particular flexwan card on the 6500 platform. The 6500 has been up for a long time and rebooting it might work but i wanted to know what should be done before i reboot the 6500.
show log:
-Process= "Pool Manager", ipl= 0, pid= 5-Traceback= 6017FA60 60183D3C 6010BE4C 60110C24 60110D80SLOT 5/1: Apr 25 11:53:39: %SYS-2-MALLOCFAIL: Memory allocation of 816 bytes failed from 0x6010BE44, alignment 8Pool: Processor Free: 18848 Cause: Memory fragmentationAlternate Pool: None Free: 0 Cause: No Alternate pool
[Code] ....
I am upgrading 6500 switch from old ios to new one and the new one requires 512/512 memory to be free below is the show ver and sh sup-bootflash,
sw-cta2-i8-off>sh ver
Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9-VM), Version 12.2
[Code].....