Cisco Firewall :: ASA 5520 Memory Utilization Over 799%

May 2, 2013

I was looking at my CISCO ASA 5520 and i found something really strange
 
ciscoasa/VPN-context# sh mem detail
Used memory:      4259249568 bytes (793%)
-------------     ----------------
Total memory:      536870912 bytes (100%)
 
but when I look at the system context this is what I see
 
ciscoasa# sh mem
Free memory:       170829000 bytes (32%)
Used memory:       366041912 bytes (68%)
-------------     ----------------
Total memory:      536870912 bytes (100%)
 
As far as I know the ASA is working good.
 
Info of the device
Hardware:   ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB

View 3 Replies


ADVERTISEMENT

Cisco Firewall :: PIX 501 - Memory Utilization?

Jul 6, 2011

I've deployed many Cisco PIX 501 v6.3.3 either as normal firewalling feature and/or with VPN features enabled. I noticed in all my deployments, regardless if it's during peak hours or after office hours, the memory utilization is always consistent 11MB utilized over the total of 16MB(memory default size).

View 3 Replies View Related

Cisco Firewall :: Memory Utilization On 5510?

Nov 21, 2012

Just want to check with you about memory utilization on the Asa 5510 ..
 
Free memory: 19%
Used Memory: 81%
 
Is this normal? Because we hade a problem this morning and the memory was at 100%.. 
 
Device Manager version 6.1(5) 57 
Hardware:   ASA5510-K8, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB

View 4 Replies View Related

Cisco Firewall :: Very High Memory Utilization In PIX 515e?

Feb 15, 2012

We had two PIXes in our environment and working as a active-failover mode. Its noted in now a days the active PIX memory utilization is 98% and for standby PIX it is 96%. And also in some times we were experiencing packet loss to the ip of active PIX and which reflects in the inside servers access also. During that time the active pix was not accessible via ssh as well as ASDM. We have tried reloading the PIX and changing failover state of the PIX, but it results only a temporary solution. Current memory installed is 128 MB (maximum upgraded), so a upgrade is also not possible. Please see the show command outputs from the PIX. Current Software version is 7.2(4)
 
sh memory output (PIX 1 - active)
 Free memory:         4850944 bytes ( 4%)
Used memory:       129366784 bytes (96%)

[code]....
 
1) How we can pin point the root cause of this high memory utilization?

2) What might be the reason for the high memory utilization for the standby pix (96%), still the PIX is in idle state?

3) Is it a hardware issue or a memory leak issue, then how can we find out?

4) Is a software upgrade to new version resolves the memory issue?

View 10 Replies View Related

Cisco Firewall :: High Memory Utilization On ASA 5510

Sep 13, 2012

We recently added about 400 users to our network for a total of 1000.  Looking at the ASDM we are holding very tight to 75% utilization and we have 256mbs.  This is also running IOS 8.2(1).  Our firewall recently crashed after a major download was forced through it.  This was after only being booted up for about a week.  We had reloaded it a week prior after having ran it for about a year without issue.  We havent made any changes in the last month other than adding more users to our network.

View 3 Replies View Related

Cisco Firewall :: ASA 5520 CPU Utilization Is 100 %

Sep 27, 2011

We have configured 20 route in ASA 5520. The CPU usage goes to 100 % at the moment when we add a specific route.route inside 10.254.101.0 255. 255. 255.0 10.254.102.254 1.This is the same case when we add this route at the first cli or as the 10th cli or the 21 cli (errespective of the position of cli) There is an another route out of which 20 routes we have configured is route inside 10.254.103.0 255.255.255.0 10.254.102.254 1.The normal case if we dont add the problamatic route , then the CPU utilization is only 2 %.

View 1 Replies View Related

Cisco Firewall :: High CPU Utilization - ASA 5520

Dec 22, 2012

we have ASA 5520 with IOS 8.0 , when i am trying to add more static routes on the inside interface the CPU utilization is going up. one faced the same issue. I am configuring through the cisco ASDM 6.1(3)f.

View 1 Replies View Related

Cisco Firewall :: High Cpu Utilization On ASA 5520?

Sep 25, 2012

I am seeing high cpu utilization on 5520.
 
fw# sh processes cpu-usage sorted non-zero
PC         Thread       5Sec     1Min     5Min   Process
0x081e1e11   0x6ddc1528   70.6%   66.5%   66.0%   Dispatch Unit
0x08ed170c   0x6ddb9b48     1.6%     1.7%     1.8%   Logger
0x08dd5f2c   0x6ddafee0     1.5%     1.5%     1.5%   SNMP Notify Thread
0x08e8d045   0x6dd99348     0.1%     0.1%     0.1%   ssh

View 2 Replies View Related

Cisco Firewall :: Would A 1GB 5510 Memory Stick Work In A 5520

Sep 19, 2012

Are the ASA memory DIMMs created for specific models?  Would a 1GB 5510 Memory stick work in a 5520?

View 1 Replies View Related

Cisco Firewall :: 5520 High Memory Usage And Error Creating Access Rules

Feb 13, 2013

I'm having a problem with the memory and also trying to create some rules on the CISCO ASA. The version that I got installed was the 8.2.5.33 on a CISCO 5520 with 512 RAM, the memory usage is on 99% used, 1% free and because of that when I'm trying to create a new rule the firewall brings me the next error..So what I did was a downgrade to the version 8.2 (4) 4 and the memory went down a little (82% used, 18% free) but I still got the error when I'm creating an access rule on the device. One thing and I'm not sure if this could affect on the performance are the number of access list and the object groups that are created.
 
I already open a case with CISCO TAC and they are checking if the problem is with the memory capacity or maybe a memory leak.Also the doubt that I got is with the memory that I got now available should I can create access rules or 82 is still to hig to create a rule or and object group?

View 2 Replies View Related

Cisco Firewall :: ASA 5520 / Crypto Errors CTM ERROR / Failed To Allocate X Bytes Of Memory

Oct 9, 2012

I am currently getting a strange error when trying to use and crypto services on our ASA 5520 (8.0.3)Initially I observed that a connected VPN had dropped.Then when I attempted to use ASDM or SSH I was blocked.
 
In the end I opened telnet as a test and this was successful. Syslog also shows that traffic is passing as normal.The only obvious error I can see when observing various debug traces is this;
 
FW02# CTM: rsa session with no priority allocated @ 0xCF1FBBA0
CTM: Session 0xCF1FBBA0 uses a nlite (Nitrox Lite) as its hardware engine
CTM: rsa context allocated for session 0xCF1FBBA0
CTM: rsa session with no priority allocated @ 0xCE7A5EA8

[code]....

View 5 Replies View Related

Cisco :: LMS 4.0.1 - High Memory Utilization

Oct 12, 2011

What causes LMS 4.1 to have high memory utilization?

View 4 Replies View Related

Cisco WAN :: 3845 Memory Utilization Increases

Jun 1, 2011

Cisco 3845 router (256RAM / 64Flash), increases the cpu utilization upto 70~80 percent, during the time of high utilization, I am unable to run show command on router.The configuration is simple, this is connected with two internet links (24Mbps and 8Mbps) and its about 600~700 users are using internet.show version, show memory and show process cpu outputs are attached here.

View 7 Replies View Related

Cisco Routers :: SA520 Memory Utilization

Aug 7, 2011

We have a Cisco SA520 Router (Firmware 2.1.18)We are only using this for about 1 month now. Router seems ok its justI am worried about the  Memory utilization which reach to 62% (144/234 MB)Is this something to worry about?How can I utilize this by lowering down the usage?

View 3 Replies View Related

Cisco WAN :: High Memory Utilization In 7206 Router

Jul 29, 2012

We have a 7206 router which acts as a MPLS Hub router for around 100+ remote locations. Bandwidh at mpls hub(terminated on this router) is 50 Mbps.
 
We have noticed that Memory utilization in this router gradually increases and when it reaches 100% this router hangs. It happence in frequesncy of 10 days and we have to restart the router when memory is 100%.
 
CPU utilization is normal i.e below 20%, WAN bandwidth will never cross 30mbps.
 
We are running OSPF on this router

View 1 Replies View Related

Cisco :: Memory Utilization OID For Catalyst 6506 Switch

Dec 26, 2012

We have one Catalyst 6506 ( with WS-SUP720-3B, IOS is 12.2(18)SXF14 ) and one Catalyst 6509 ( with WS-SUP720-3B, IOS is 12.2(18)SXF17a ). We used WhatsUP to collect I/O & process memory utilization for both switches. The memory utilization for Catalyst 6509 was ok, but it seems not correct for Catalyst 6506 ( show proc memory displayed the total memory is 512MB, but the WhatsUP displayed only 64MB only )

View 1 Replies View Related

Cisco Infrastructure :: 2960 - High I / O Memory Utilization

Oct 26, 2011

We recently installed two 2960, both of them with this fw version:

Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
 
The switches see very few traffic (under 40MB on all interfaces, summed, so far), however, I/O memory utilization is about 80% as can be seen from the show memory command:
 
Head    Total(b)     Used(b)     Free(b)   Lowest(b)  Largest(b)
Processor    2B89A18    73969000    27198964    46770036    45060368    29367536
      I/O    6200000    14680064    12185292     2494772     2323116     2380896
Driver te   1A00000     1048576          44     1048532     1048532     1048532
 
The memory allocated is almost all Packet Data, by init, "sho memory io dead" returns  zero, the memory usage seems constant, there are no errors on the log, the switches operate correctly, no packet has ever been dropped, CPU usage is about 4%.
 
Here I showed info for one switch, the other is in the same situation. I just want to know if this behavior is expected, I don't want to find out problems when the switches will be in production whit real traffic.

View 5 Replies View Related

Cisco :: High Memory Utilization After Few Days - Ciscoworks LMS 4.0.1

Sep 18, 2011

I have the problem that our ciscoworks server gets out of memory after few days. The memory utilization is always getting higher an higher (above 95%). Sometimes it is only after 3 days and sometimes it is after 1 week. So it happens not regularly. I have made an screenshot from the services which use a lot of memory. And at this time the memory utilization is getting higher and higher again....I think there is a problem with tomcat or dbsrv10.exe, there are also a lot of cwjava.exe running.

View 8 Replies View Related

Cisco Switching/Routing :: High Memory Utilization SW 3750

Sep 6, 2012

I have a Switch WS-C3750E-48PD-SF with IOS 12.2(58)SE2 which reports more than 80% in utilization of memory I don't know what is causing the high memory utilization.

View 14 Replies View Related

Cisco AAA/Identity/Nac :: ACS Memory Utilization Limit With CSACS 1121

Aug 21, 2012

We have 2 CSACS 1121 with Cisco ACS 5.2.0.26.10 The primary server manages 20000+ authentications per day. Its memory utilization increases everyday. It is now at 83% , there a limit?,What will happen when memory utilization reach this limit?,What can we do to purge memory utilization? (reboot, service restart.

View 11 Replies View Related

Cisco Switching/Routing :: 6509 High Memory Utilization?

Dec 6, 2011

I've noticed that my 6509's running VSS seem to have high I/O memory utilization.
 
I/O memory: Sw/Mod         Bytes:       Total           Used           %Used
             1/1                      8126344        7886544             97%
             1/2                     11796240       11442472             97%
             1/5  RP                 12058384       10715832             89%
             1/5  SP                  8388608        8104304             97%
             1/7                      8126344        7886544             97%

[code]....

View 5 Replies View Related

Cisco WAN :: 5540 - Memory Utilization Getting Higher When Adding Tunnel

Jul 21, 2011

We terminated about 25 site-to-site VPN tunnels on the Cisco ASA 5540 (2 GB RAM). It appears that the memory utilization is getting higher when adding the tunnel. We are planing to remove those 25 VPN tunnels out 5540, and soon we will add additional 40 VPN tunnels on it. So it will be total around 65 tunnels, and maybe add couple tunnels per year for the future grow, but about 25 VPN tunnels are using at all the time, the others are just backup purpose, standby only. We are looking for the new network device (router or ASA) to accommodate the needs. Which network device is better to handle VPN tunnel for this infrastructure?

View 5 Replies View Related

Cisco Switching/Routing :: 2960 High Memory Utilization

May 2, 2013

I noticed on the 2960 switches we have deployed that are running the latest IOS, 12.2(58)SE2, memory utilization is really high (almost 80 percent). I have not noticed any side effects but I wanted to verify this is acceptable. My question is does the high memory utilization matter? I see this may be related to bug CSCtw83946 but no resolution is mentioned.
 
I did some testing various IOS revisions and below is what I have found using a WS-C2960-48TC-L with default configuration and only my laptop connected to a switchport in vlan1. You will notice memory utilization will grows with each version but jumps drastically with 58. One difference with 58 I needed to use a different command to retrieve memory utilization. The output was gathered by pasting the output of the show command into the Cisco Output Interpreter on their website.
 
IOS
Show Command
Output
c2960-lanbasek9-mz.122-35.SE5.bin
show memory
[Code]....

View 8 Replies View Related

Cisco Switching/Routing :: High Memory Utilization In WS-C2960-48TT-L

Nov 9, 2012

I am facing high memory utilization in Cisco 2960 switch having IOS version 12.2(55)SE3.
 
The error we are getting is:
 
A "LiveHealthAlarm" event has occurred, from SwCiscoIOS device, named Switch2960.  eHealth Alarm Start Time - Fri 09 Nov,2012 - 03:02:48 eHealth. Switch2960-RH-MemoryPool-Processor-Processor-1.Memory utilization high-Threshold set at 70%SPECTRUM ALARM ID|22233284 I have attached the logs also.

View 3 Replies View Related

Cisco Switching/Routing :: 3750 Stack - High Memory Utilization?

Jan 21, 2012

I have a new cisco 3750 stack comprised of 8 members (6 x 3750G-48PS and 2 x 3750V2-48PS) running 'c3750-ipservicesk9-mz.122-58.SE2.bin'. I am seeing high memory utilisation, it seems to sit fairly stable and I do not see an increase but this has only been running a few days. No errors or performance issues. Should this be a cause for concern?

View 3 Replies View Related

Cisco Switching/Routing :: 3750g And 3750x High Memory Utilization?

Jun 11, 2013

We had a stack of 4 qty 3750g running IP base on ver 12.2.32, then installed a 3750x to the stack and upgraded the whole stack to 15.0.2 SE3. In doing so, we noticed that the memory utilization jumped from 60-70% to 83-84%.
 
We had the same issue occur when upgrading to 15.0.2 SE3 on another stack that was 6 qty 3750g running ip-services, but this one jumped to 90%.  On the 6 qty stack, we downgraded to 12.2.55 and the memory util went back down to 60-70%. 
 
On the mixed stack, we replaced the 3750x with another 3750g and downgraded the whole stack to 12.2.55, however, the memory utilization did not drop down.  As far as I can tell, no config changes have changed from the original IOS. 

View 4 Replies View Related

Cisco Switching/Routing :: C2960-24-TT-L - Switch Memory Utilization High After Upgrading IOS

Nov 8, 2011

I upgraded the newest IOS 15.0(1)SE for our SW C2960-24-TT-L, the process was succeseful. However, we found SW memory utilization raised to 82% this morning in normal situation. (Momery: Total 21341260, Used17471692) Did you guys meet the same problem after upgrading to 15.0(1)SE? I also would like to know what the normal memory utilization is? and what is the impact of memory utilization highly?

View 8 Replies View Related

Cisco Switching/Routing :: High Memory Utilization Of 3560 Switch After Upgrade IOS

Mar 5, 2013

I upgrade the IOS of my switch 3560 from   C3560-IPBASE-M), Version 12.2(25)SEB4,  To   C3560-IPBASEK9-M), Version 12.2(55)SE5 after that the utilizatio of the memory increase to 80% I attached the output of show memory statistics history

View 5 Replies View Related

Cisco Firewall :: ASA 5520 - Memory Shows 94% And CPU Shows 85%

Oct 15, 2012

I Have asa 5520 with the  code 8.0, the mem shows 94% and the CPU shows 85%

View 5 Replies View Related

Cisco Switching/Routing :: High Memory Utilization On Line Card 6748 And 6724?

Apr 15, 2012

I am writing with regard to a high memory utilization that we have on a pair of line card WS-X6748-GE-TX and WS-X6724-SFP for a VSS 6500. I am enclosing a little part of the "show tech"of this VSS 6500 where is possible to see the high memory utilization of the line cards 1/1, 1/2, 2/1, and 2/2, in despite of having some ports in state connected.  In addition of this, the IOS installed on VSS 6500 is s72033-ipservicesk9_wan-vz.122-33.SXI6.bin for checking if there are some bugs affecting the behaviour of the Switch for this case.
 
 System Resources
  PFC operating mode: PFC3C
  Supervisor redundancy mode: administratively sso, operationally sso
  Switching resources: Sw/Mod    Part number               Series      CEF mode
1/1      WS-X6748-GE-TX            CEF720           CEF
1/2      WS-X6724-SFP              CEF720           CEF

[code]....

View 1 Replies View Related

Cisco VPN :: ASA 5520 - Error / Memory Allocation Failed

Apr 2, 2012

I am running IOS version 8.0(5) in cisco ASA 5520. This issue i am facing is that when the memory utilzation reaches 49 percent, the web-vpn users are not able to login as they are getting a blank page. The only error which is getting in the output " sh mem webvpn allobjects" is ERROR: Memory allocation failed?

View 2 Replies View Related

Cisco Infrastructure :: Not Getting CPU Utilization Info For ASA 5520

May 30, 2012

Device config is shown as follows in application doing the discovery.  Cisco ASA 5520. [code] Is there any new updated agent available for Cisco ASA 5520 that contains the oid  ".1.3.6.1.4.1.9.9.109.1.1.1.1.8 "

View 4 Replies View Related

Cisco VPN :: 5520 - Monitoring IPSec Tunnel Bandwidth Utilization

Sep 8, 2011

We have a Cisco ASA 5520 supporting multiple VPNs - both remote-access  and Lan-to-Lan.  We would like to monitor the bandwidth utilization of the IPSec Lan-to-Lan tunnels.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved