Device config is shown as follows in application doing the discovery. Cisco ASA 5520. [code] Is there any new updated agent available for Cisco ASA 5520 that contains the oid ".1.3.6.1.4.1.9.9.109.1.1.1.1.8 "
View 4 RepliesWe recently installed two 2960, both of them with this fw version:
Cisco IOS Software, C2960S Software (C2960S-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
The switches see very few traffic (under 40MB on all interfaces, summed, so far), however, I/O memory utilization is about 80% as can be seen from the show memory command:
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor 2B89A18 73969000 27198964 46770036 45060368 29367536
I/O 6200000 14680064 12185292 2494772 2323116 2380896
Driver te 1A00000 1048576 44 1048532 1048532 1048532
The memory allocated is almost all Packet Data, by init, "sho memory io dead" returns zero, the memory usage seems constant, there are no errors on the log, the switches operate correctly, no packet has ever been dropped, CPU usage is about 4%.
Here I showed info for one switch, the other is in the same situation. I just want to know if this behavior is expected, I don't want to find out problems when the switches will be in production whit real traffic.
We have configured 20 route in ASA 5520. The CPU usage goes to 100 % at the moment when we add a specific route.route inside 10.254.101.0 255. 255. 255.0 10.254.102.254 1.This is the same case when we add this route at the first cli or as the 10th cli or the 21 cli (errespective of the position of cli) There is an another route out of which 20 routes we have configured is route inside 10.254.103.0 255.255.255.0 10.254.102.254 1.The normal case if we dont add the problamatic route , then the CPU utilization is only 2 %.
View 1 Replies View Relatedwe have ASA 5520 with IOS 8.0 , when i am trying to add more static routes on the inside interface the CPU utilization is going up. one faced the same issue. I am configuring through the cisco ASDM 6.1(3)f.
View 1 Replies View RelatedI was looking at my CISCO ASA 5520 and i found something really strange
ciscoasa/VPN-context# sh mem detail
Used memory: 4259249568 bytes (793%)
------------- ----------------
Total memory: 536870912 bytes (100%)
but when I look at the system context this is what I see
ciscoasa# sh mem
Free memory: 170829000 bytes (32%)
Used memory: 366041912 bytes (68%)
------------- ----------------
Total memory: 536870912 bytes (100%)
As far as I know the ASA is working good.
Info of the device
Hardware: ASA5520, 512 MB RAM, CPU Pentium 4 Celeron 2000 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
I am seeing high cpu utilization on 5520.
fw# sh processes cpu-usage sorted non-zero
PC Thread 5Sec 1Min 5Min Process
0x081e1e11 0x6ddc1528 70.6% 66.5% 66.0% Dispatch Unit
0x08ed170c 0x6ddb9b48 1.6% 1.7% 1.8% Logger
0x08dd5f2c 0x6ddafee0 1.5% 1.5% 1.5% SNMP Notify Thread
0x08e8d045 0x6dd99348 0.1% 0.1% 0.1% ssh
We have a Cisco ASA 5520 supporting multiple VPNs - both remote-access and Lan-to-Lan. We would like to monitor the bandwidth utilization of the IPSec Lan-to-Lan tunnels.
View 3 Replies View RelatedI am going to be updating the IOS on our Cisco ASA 5520 from verion 7.0(8) to 8.2(5). I am also going to setup AnyConnect. Are there any major changes in the 2 IOS versions that I need to be aware of or will the config work in either version? Also, we are currently using the Cisco VPN Client to connect to our network. Will that still work after the upgrade?
View 3 Replies View RelatedI want to configure a MAC address on my asa 5520 interface.I ask you if exist a private MAC address range?
View 5 Replies View Relatedyesterday I tried to connect to our ASA 5520 using ASDM Launcher, which has alwasy worked before. For some reason ASDM Launcher is no longer working from both my Win XP desktop and Win XP laptop. I can open ASDM through the browser but not the launcher. Both desktop and laptop have Java 7 U 6. I'm not sure if I can back rev my Java.
View 4 Replies View RelatedAll my switches were connected together as ring topology. We use REP to block redundancy link.One of my colleagure was setting up a new link(VLAN) for one customer which was then caused a L2 loop. The CPU was hitting 100% and REP started to lost neighbors then we had a big outage.I am thinking to deploy QoS on all REP switch (on trunk links from switch to switch) to give priority to control traffic like REP and some importance data VLAN. Of course,Storm-Control already implemented on all access-port.
View 2 Replies View RelatedI am new to load balancing technology pls give me the articles for load balancing technology of servers & want to know about CSS 11500 switch.I am Interseted to know about SAN do for the same.
View 1 Replies View RelatedNowadays, people have smartphones, typically iPhones and Android phones, and they all have WiFi.We already have a wireless net set up, with 802.1x security, where people connect using certificates and user informations stored in AD..I would like to see the smartphones use the same SSID as the computers, using the owners user info from AD.But I think user info from AD only is too weak (since I cannot use certificate enrollment on the phones), so I would like to add the smartphone's mac address to the internal hosts database, too, so I have 2 layers of security:If smartphone mac exists in internal hosts, then authenticate it with AD information.When I try this, I only get the message that the user credentials does not exist in Internal users, and then it fails.
View 12 Replies View RelatedI have successfully set up a pptp vpn from my new rv220w. I have also successfully logged in using 2 seperate laptops and also my iPhone. They all work great. There is one issue. When connected and I log into the router it does not show these laptops or iPhone as being connected to the vpn. There is two spots that its supposed to show the page refreshes and shows nothing connected. Is there a setting I am missing?
View 2 Replies View RelatedAny info about OPT_E_MAN, I want to run from A to B with two 3750.
View 3 Replies View RelatedI'd like to be able to have access to all the hard drives that are on both networks, with the aim of easy media sharing.Heres what i'm working with so far,I've got two networks each in a different apartment, each with internet access with a different provider.Network A has a wifi n duel band router, with two PS3s, two Xbox360s, two computers (one Macbookpro OSX and one PC win7 ) and one Wii all connected to the router wierlesly.Network B has a wifi, with PS2, Xbox360, a laptop win7 and a pc win7 I also have a portable hard drive, that i want to have access to wirelessly.'m not sure where to start, how to gain access to the other network without using the internet.I've been told that i'd have to get a server, but i'm not very computer lit, i just want the freedom of info over the two networks.
View 2 Replies View RelatedIam fairly new to Cisco IOS and am having trouble getting an IPSEC tunnel to come up between 2 cisco 881-s. I have entered both debug crypto isakmp and debug crypto verbose but when I try to ping an internal IP at the other location through my VLAN1 interface no debugging info comes up.
Also my ACL-s for the crypto maps show no activity. I have tried many things so my configuration files are starting to get really messy.
[code]...
I enabled dual stack on my rv042g router but its not recieving ipv6 information from my isp. My isp is Time Warner in Milwaukee. They assure me that they are ipv6 ready and assume the problem is on my end. All they want to do is have me connect one computer up to my modem. What good is that when I have a network that needs service. The router needs to be working not just one pc. My ipv4 is working perfectly. It is obtaining all information automaticly.
View 3 Replies View RelatedIs it possible to see device information for equipmnet that is logged into the AP541N access point? I was able to determine a specific IP address was eating a significant amount of bandwidth and was hoping to get the device information (name, type, etc) in the hopes of tracking down who it was.
View 1 Replies View RelatedI have two ACS1152 appliances running as a redundant pair. I notices that secondary box keeps losing its repository information in the config.
View 2 Replies View RelatedI've got tons of fibre in my network. However, tbh, my knowledge about correct light levels isn't great. I generally wait until my router complains about a light level before I do anything. I would like to set up SNMP monitoring for light levels, but I need some kind of baseline.Anyone with extensive fibre experience? What light levels should I be looking at for both multimode and singlemode fibre?
View 6 Replies View RelatedI am Using Micromax A75 how can i know my mobile wifi Network ssid
View 1 Replies View RelatedBelkin router model FD305v1 no longer being provided any technical support by its Makers.You have to pay for it now. My router went out and first of all it's hard to find any information even on their own website. And if you do you still have to pay them to get it working again
View 2 Replies View RelatedI was setting a static IPs for my PCs, and for the Preferred and Alternate DNS Server addresses I looked on my router's Device Information page. It had "Primary DNS Server: 121.98.0.1", but "Secondary DNS Server:" is reported as "0.0.0.0". Router is a DIR-655:
I looked on my ISP's website and they have "121.98.0.2" listed as the Secondary Name Server/DNS:
Why does the router not report that? Is there something wrong? Should I still set 121.98.0.2 as the Alternate DNS Server in Windows?
EDIT: BTW, my modem reports both primary and secondary DNS servers on it's info page.
I have two CSS 11503 in my network, recently we had configured sticky with advanced-balance arrowpoint-cookie.
The sticky is functioning but we found our server's private IP in the IE cookie ARPT box.
Is there any way to hide ARPT info? Below is an example configuration of my CSS and attached screenshot is Firefox cookie info.
content 5301
add service 172.18.71.77_5301
add service 172.18.71.77_5302
[Code]......
We have Cisco 3945 Router and generating crashinfo while firing PRI from this Router.
View 1 Replies View RelatedThe rouge access points being detected by the 5508 WLC are not showing up on the Context Aware tab of NCS? I have a MSE 3310 installed and configured and it shows to be syncronizing with the WLC. I'm sure I am missing some part of the configuration just not sure where.
View 3 Replies View RelatedOur 6500 was reboot by self with crash info and i found it was happened by CPU HOG. The log is below for CPU HOG and you can see many times from attached crash info file.
%SYS-SP-3-CPUHOG: Task is running for (16000)m secs, more than (2000)m secs (15/12),process = RPC pagp_switch_mp2sp.
[code]....
I think this process made high CPU & memory issue and then there were internal communication fail.. isn't it? So i need to know what PRC pagp_switch_mp2sp is to prevent next issue.
C1921, running version 15.1(4)M2, with licence for "IP base" feature set only.Trying to pass multicast via a PPTP VPN from a Windows XP machine to work around a non multicast-aware WAN link
1. With the IP Base feature set I am able to create a plain PPTP VPN without any encryption; the Windows XP machine can bring it up and unicast data passes through it OK in both directions.
2. But when trying to send multicast, only one-way traffic is observed:i. Windows XP host on far end of PPTP VPN and a local PC both running old Microsoft tool "MPING.EXE", sending and listening for traffic on the groiup 225.100.101.102i. The distant host receives and echoes back the packets received from the local machine + sending its own (confirmed with Wireshark running at the far end)ii. But the local machine directly connected to the C1921 router does not hear any packets from the far end; Wireshark shows only the ones it is sending.
3. Group status ("show ip igmp membership") as far as the C1921 is concerned shows both ends (192.168.50.10 (local end) and 192.168.50.201 (distant end via the PPTP VPN)) joined to the group [code]
4. But "show ip mroute" for that group shows an error; for the source on the far end of the PPTP VPN (having the IP address 192.168.50.201), the source interface is incorrectly shown as GigabitEthernet0/0 (should be Virtual-Access2.1 for that PPTP VPN) and the outgoing interface is shown as Virtual-Access2.1 [code]
5. I have tried adding static mroutes and messing about with parameters for the virtual-template interface for the PPTP VPN, but the problem remains. And if I put another local PC onto a different Ethernet port of the router, the multicast traffic does flow both ways - so the issue is solely with the PPTP VPN.After a week of head-scratching I am getting more and more convinced that it's a bug... but wonder if it is already-known, has a workaround, or a fix in newer firmware?
I cant find any info for my router F9K1004 on belkin's support site. I would like to see if there is a firmware update and if there is any info to setup my VPN at home.
View 1 Replies View RelatedIn CUCME if you do not configure any translation rules and leave the system mainly at default, when a call is routed to the PSTN the CUCME system sends the true calling party ID which would be a users extension number. Is it correct to assume that a CUCM server based system, when too left at the majority of default (without translation rules or stripping etc) that it will send the true calling ID to the gateway?
View 1 Replies View RelatedI have a Cisco WS-C6513 switch, with a couple of GBIC module cards in it. I am trying to display the part number (or model number) of the modules which are inserted into this module card. How to do that? I don't want to schedule down-time to pull the module(s) - just to read the label! :-)
This shows me info for the "module card": sh module 9 But this doesn't work: sh module 9/6
I have an RV220W with firmware version 1.0.2.4. My ISP makes available IPv6 over PPPoE in a Dual Stack configuration. One of the requirements is that my home router should support prefix delegation. I don't appear to be able to find any information pertaining to PD in relation to the RV220W -
View 6 Replies View Related