DIR-655 - Secondary DNS Server Blank In Router Info
Jul 14, 2011
I was setting a static IPs for my PCs, and for the Preferred and Alternate DNS Server addresses I looked on my router's Device Information page. It had "Primary DNS Server: 121.98.0.1", but "Secondary DNS Server:" is reported as "0.0.0.0". Router is a DIR-655:
I looked on my ISP's website and they have "121.98.0.2" listed as the Secondary Name Server/DNS:
Why does the router not report that? Is there something wrong? Should I still set 121.98.0.2 as the Alternate DNS Server in Windows?
EDIT: BTW, my modem reports both primary and secondary DNS servers on it's info page.
View 6 Replies
ADVERTISEMENT
Mar 2, 2011
In ACS 5.1 how do I promote the secondary server to local mode if I have lost the primary server, in this scenario is it only accessible by the CLI and would you have to manually promote it so as to enable further configuration elements via the GUI? I would have thought that if the primary failed some sort of keep alive from the primary to the secondary would be lost thus making the secondary force it's own promotion but this does not seem to be the case???
View 2 Replies
View Related
May 29, 2013
My customer has an ACS 1121 version 5.4. Now we want to install a secondary ACS 1121.
View 2 Replies
View Related
Feb 28, 2013
We are using ACS 5.3 with two servers in a distributed solution.All logs are collected on primary server so when this server fails all logs are lost.How can I enable log on secondary server also?
View 2 Replies
View Related
Oct 23, 2012
We have 4 ACS 5.3 Servers connected as Primary and Secondary Servers.We use a "RSA SecurID Token Servers" External userdatabase for authentications and are able to sucessfully authenticate (vpn-)users when the requests are send from the primary ACS Server.As soon as a secondary ACS server sends the request to the RSA server the request fails. "Node verification failes"
On the RSA Authentication Manager 6.1 Server, we have created a Agent-host wich contains the 3 secondary nodes (FQDN and IP's). The "sdconf.rec" file has been installed on theprimary ACS Server and are automatically (so it looks like) replicated to all ACS Servers.Still none of the secondary server are able to authenticate the users agains the RSA server.
View 1 Replies
View Related
May 15, 2011
Can we assign Secondary ISP-2 Pool IP to DMZ Server, network design attached for reference.
View 2 Replies
View Related
Apr 21, 2013
I have a couple of ACS 5.2 configured as active and backup and I am doing dot 1x authentication using these servers . I have configured the switch with the bellow configuration.
radius-server host 10.0.10.15 auth-port 1645 acct-port 1646
radius-server host 10.0.10.16 auth-port 1645 acct-port 1646
radius-server key 7 aaaaaaaaaaaaaa
please help to understand what will happen in switch
1) in case of primary failure
2)in case if primary returns alive .
View 8 Replies
View Related
Nov 2, 2011
Cisco ACS 5.2 secondary server is configured as a log collector for both primary and secondary server .Now i am facing problem in log collection from primary server .ACS secondary server is not collecting any logs from primary .
View 2 Replies
View Related
Jul 29, 2012
I am trying to change the name of my wireless network but when I go to the 192.168.1.1 and type in my password, it just goes to a blank screen. I've accessed my router a lot of times before this way. It is a lisksys router.
View 1 Replies
View Related
Jan 28, 2010
BEFSR81 v3.1 Current firmware 2.51.4 build 600 (09-4-2009)The Web Admin pages become dysfunctional after the router has been up 3-4 days displaying only a blank white page. Viewing the page source shows that the HTML is incomplete.I am not sure of the exact firmware version where this problem originates, I noticed it after flashing to 2.51.4 build 400 but cannot remember which version was running before the update. Just flashed to 2.51.4 build 600 last week hoping the new version had corrected the problem. Still broken.The router remains completely functional but the Web interface does not work correctly after 3-4 days.I have tried re-flashing the firmware and have gone as far as resetting the router both before and after the flash, even tried 30/30/30 resets but the problem with the Web interface remains.Re-booting the router every 3 days is not the best “solution” as my network is running DHCP. I would rather not fall back to older firmware as ver 2.51.4 build 400 corrected the DHCP errors on my Windows machines and decreased the initial connection time when machines boot up. I have read in this and other forums where others are having the same problem with this router/firmware but have been unable to find a working solution which leads me to believe the actual problem resides in the later firmware builds.
View 9 Replies
View Related
Dec 14, 2012
I am using Windows 8 and my router is a Linksys E2500, in the Network folder it shows no icon and also I get a error when I right click the device and choose "Network Map" (from what I can tell this feature has been removed from Windows 8.) Both these problems are cause by an outdated Windows 7 driver on the Microsoft Update Catalog (I have Windows 8 configured to download updates/drivers automatically, that's why this installs)The reason there is no icon is because of these entries in the driver INF
[code]....
View 3 Replies
View Related
Feb 23, 2013
Blank user name and admin in password doesn't work. How to reset these ?
View 1 Replies
View Related
Mar 15, 2013
Region : Austria
Model : TL-MR3420
Hardware Version : V1
Firmware Version :
ISP : orange.at
When I first installed the router I used the built-in provider settings for "ONE" which used to be the name of the provider before it was taken over by orange.at. It seemed to work fine but I experienced some funny server errors with certain web services. I contacted orange.at about this and they told me to adjust the provider settings in the router as follows:
Dial number: *99#
APN: fullspeed
The reason for the problems was that they use different proxy servers for their services and applications. Now it works fine (so far).
View 1 Replies
View Related
Jun 15, 2011
We have Cisco 3945 Router and generating crashinfo while firing PRI from this Router.
View 1 Replies
View Related
May 17, 2011
BEFSR81 will not save port forward info. I am trying to setup port forwarding for xbox (53, 80, 88, 1863, 3074), I click on enable to the far right and then click save at the bottom. It says settings are succeful, will return in 5 seconds. When it returns everything is zeroed out.
View 3 Replies
View Related
Mar 19, 2011
How do I know if I'm using 2.4 or 5ghz? I would like the laptop and ps3/net flix to use the 5ghz and everything else to use 2.4ghz. I used the e3000 CD fro the setup. When I was at the last part of the setup, when it gives you a ssid name and password. I deleted it and typed in a name that I could remember. I clicked the button for the next step and everything was complete. I also received another name for guest to use the computer. The e3000 setup just game me some wild name like running water.
I would like to know since I have two different names, which on e is using 5ghz and which one is using 2.4thz? Can you tell me if the e3000 automatically have the first name use 5ghz and the guest just 2.4ghz on the second name?
View 3 Replies
View Related
Apr 25, 2011
I have been having problems when trying to host servers on games, etc.I have 2 routers. A modem router, which is a Thomson router. That is the main one. It has a wire connecting from it, to a D-Link router that is near my Computer, and my brother's one. Then that D-Link router has 2 wires from each port, to mine, and my brother's computer.So, I am trying to host games.I didn't connect to the Thomson one, which is also wireless. I am connected to the wired one (D-Link). When I try to host while connected to it, my brother, and other people can't find the server. My brother and me can find it on LAN, but not Internet.But when I disconnect from the Wired, and connect to the Thomson wireless one, and then when I host, I can find it on INTERNET. Even my brother can. He can connect to it perfectly.
I do not want to connect to the wireless, because then it will cause lag spikes every 5 minutes.So, when I disconnect from the wireless, and connect to the wire, I went into the CMD, and typed in ipconfig. I found out that the Default Gteway is the D-Link IP.When I connect to the wireless, and disconnect the wired, I went into CMD, and then the Default Gateway is the Thomson one, which is the main router.So what I want to do, is use the D-Link router, and that router will have the same IP as my thomson one, so that I can host perfectly with no lag spikes, and using a wired connection.
View 19 Replies
View Related
Aug 1, 2011
I currently have my wired cable internet hooked into my wrt310n. I have that hooked into a linksys 10/100 ef3124 switch. From there, I have cat5 run to the back of my house, where the wireless signal is weakest. I've got an E2000 router and would like to hook that in at the back of the house. What settings do I need to make in order to set up a completely new wireless network in the back of the house?
View 1 Replies
View Related
Jan 30, 2013
I have two routers on my local network:
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled)
2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2
There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the same subnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it possible by configuring the DHCP server to assign the primary DNS address as 192.168.1.1 and secondary DNS address as 192.168.1.2?
View 11 Replies
View Related
Feb 22, 2013
I have more than 5000 sq. ft home and have some dead places other end of the house. Now I am looking for Range Extender/Repeater to boost signal. My primary wireless router is Motorola Surfboard SBG6580 and Secondary Linksys E3000 (planning to update firmware to DD-WRT). So I wanted something such that I can roam between the two routers without switching SSID (use single SSID name for primary and secondary DD-WRT routers) and connect automatically to whichever the best signal (or) strength router. In work place we have same thing like that single wireless SSID name which automatically connect wireless SSID from one end to another end of the building.
View 1 Replies
View Related
May 22, 2013
I have an MPLS network router(Router1) and an internet router(Internet1) at a site of mine(Site1). the MPLS router sends all unknown traffic out the internet router. Router1 is the default gateway for all hosts and directs the traffic.I also have another network at an alternate site (Site2) on the same mpls network also with an internet egress. It is composed of an MPLS router (router2) and an internet router (Internet2).I would like Router1 to send internet bound traffic out Internet2 if Internet1 is down. Basically the statement on Router1 for the unknown traffice is ip route 0.0.0.0 0.0.0.0 172.31.1.254I have never heard of IP SLA before but it seems to be the best method for this situation.
View 2 Replies
View Related
Sep 7, 2012
We have a dsl connection on 897 dsl router at the customers HO.The telephone line is directly connected to router we configured dialer with username and password and it takes a static ip of 212.249.213.xxx.Now he has some branches that are connected through wireless links and he has arranged for a subnet of 8 public IP's in the range 72.70.245.xxx
Can we some how use these public ip's as secondary in the routers dialer interface and assign to the servers in the branches so that it can be accessed through web.
View 1 Replies
View Related
Aug 24, 2012
my screen goes blank if not used after about 10 mins how do i extend time?
View 1 Replies
View Related
Nov 25, 2012
My client has an 857w, but although the site for the SDM express loads, the Internet WAN page always shows as blank. We need access to this to alter the ISP.On IOS 12.4(6)T5
View 7 Replies
View Related
Jan 30, 2013
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled) 2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the samesubnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it
View 4 Replies
View Related
Aug 13, 2012
Since the secondary router WRT300N uses the same default IP 192.168.1.1 as the primary installed router EA4500, any attempt to log onto the set up page results in diversion to the Cisco Connect Cloud for the primary router.
Is there a way to access the set up page for the secondary WRT300N, bypassing the main router intervention via the Cloud software?
View 3 Replies
View Related
Feb 25, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : fullrate.dk
My ISP has provided me a router: Zyxel P-2601HN which has an ideal WLAN transfer rate of 150 mbps. I live in a concrete 2 story house so signals are weak at best on the other floor - therefore, I Have bought the TL-WDR4300 as an extension for the latter floor. I have connected the routers from LAN to LAN and the Zyxel has 192.168.1.1 on LAN and the TL-WDR4300 had 192.168.0.1 as out set. I have changed this to 192.168.1.2 and all the setup (disabled DHCP + other) seems to work alright. BUT i can not log into the TL-WDR4300 !! Not with http://192.168.1.2 and not with [URL]. What I can do to get into the setup of TL-WDR4300. I know I can alays backup the setting and reset the router and load the setting again, make alterations, saving .....but it kind of drastic !Can the two radios SSID names (2,4 MHz and 5 MHz) be the same name as the SSID name on the Zyxel P-2601HN ? What are the implications ?
View 3 Replies
View Related
Aug 21, 2011
I have a set up for cable modem internet i would like to share with a laptop.Its a Motorola surfboard cable modem hooked up to my IBM P4 computer through a USB cable. The Ethernet port out of the modem is NOT operational.The IBM computer gets the internet fine in this configuration. I would like to use a SRX200 WiFi router to connect a laptop to my internet using ICS and leaving the IBM computer and router on when i do this.I opened properties on the USB connection and clicked share internet connection.This then set up my Ethernet port to 192.168.0.1.I now want to connect the SRX 200 to the Ethernet port. Its IP is 192.168.1.1.so, do i connect the computers Ethernet port to one the routers Ethernet ports instead of the wan port?Do i turn off the routers DHCP? Do i have to change the routers IP address to make this work? Will i have to assign fixed IP's to my client to make it work?
View 1 Replies
View Related
May 11, 2012
I set up a linksys e2500 router with name "mynetwork" and WPA2 password.
The network works fine, my laptop connects securely to it.
But when I View Available Wireless Networks , I see a second , unsecure network named "mynetwork-guest" to which my laptop will also connect with no credentials (not sure how that network got there).
How can I find and delete that unsecure network? When I go into my router setup, I only see mynetwork, not mynetwork-guest If it is of any use here is the IP information for both:
The settingd for mynetwork:
IP Address: 192.168.1.133
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
The setting for mynetwork-guest:
IP Address: 192.168.33.137
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.33.1
View 2 Replies
View Related
Jul 11, 2012
i changed the hd in a nm-cue and configured the router accordingly and i opened a session to it but the screen is blank.
[code]...
View 4 Replies
View Related
Jan 29, 2012
I recently installed LMS 4.1 on a freshly installed W2k8R2 server, and untill last week I had no problems logging on. For some reason, I'm now getting a blank page after entering my credentials. The URL is like [URL] I already rebooted the system, but that made no difference. All Cisco Works services seem to be started, as is Apache/2.2.17.
View 1 Replies
View Related
Apr 11, 2012
i want to find out my router ip address, but when i go to cmd & run ipconfig my default gateway shows blank. i want the router ip in order to access my CCTV footage through the internet. my router/modem is BSNL Broadband model no DNA-A211-I. i can however connect to the internet without any problems. just want to find out my router ip address.
View 11 Replies
View Related
Dec 8, 2011
I am in vain trying to transfer image to my asa5505, but fails in last step copying the file to flash:
Boots to rommon
tftpdnld image -> asa5505 boots on tftp file in en mode, i try to copy command but this fails, always getting No such device error. I have tried all different solutions found on google for this step, but it simply does not work, as i am never able to ping anything from the ASA.
rommon #6> tftpdnld
ROMMON Variable Settings:
ADDRESS=192.168.1.115
SERVER=192.168.1.113
GATEWAY=192.168.1.254
PORT=Ethernet0/0
VLAN=untagged
IMAGE=asa805-k8.bin
CONFIG=
LINKTIMEOUT=20
PKTTIMEOUT=4
RETRY=20
tftp asa805-k8.bin@192.168.1.113 via 192.168.1.254
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
ciscoasa# copy tftp disk0:
Address or name of remote host []? 192.168.1.113
Source filename []? asa805-k8.bin
Destination filename [asa805-k8.bin]?
Accessing tftp://192.168.1.113/asa805-k8.bin...
%Error opening tftp://192.168.1.113/asa805-k8.bin (No such device)
Apparently it dont work with Eth, nor with vlan 1. Any way to shut down all functions in router so i can access everything?
View 2 Replies
View Related
