Linksys Wireless Router :: Remove Secondary Network From E2500?
May 11, 2012
I set up a linksys e2500 router with name "mynetwork" and WPA2 password.
The network works fine, my laptop connects securely to it.
But when I View Available Wireless Networks , I see a second , unsecure network named "mynetwork-guest" to which my laptop will also connect with no credentials (not sure how that network got there).
How can I find and delete that unsecure network? When I go into my router setup, I only see mynetwork, not mynetwork-guest If it is of any use here is the IP information for both:
The settingd for mynetwork:
IP Address: 192.168.1.133
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
The setting for mynetwork-guest:
IP Address: 192.168.33.137
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.33.1
View 2 Replies
ADVERTISEMENT
Feb 25, 2013
I have the following equipment
E2500 wireless N router (2 of these)
WRT54g router (B/G)
WAP54g access point (B/G)
I am planning to set up a Wi-Fi network for a single story motel. It is C-shaped; about 300 feet along the longest side with "legs" of 120 and 70 feet.Until now I have only used that single WRT54g in the office for the entire property and it covers about half the property (left side.) My plan starts in the office (bottom left) with a WRT54g connected to the DSL modem as it always was. That would be connected to one of the E2500s in the middle so it can cover the most area. From there two others would shoot out to each corner (the other E2500 and the WAP54g). They will all be wired together with Cat 5e "riser cable". The routers will be placed in a wide open attic.
1. I have heard that N routers have a range of 150ft in every direction so that's why I'm putting one in the middle. Keep in mind that while the attic is open and wood constructed, the walls between rooms are concrete firewall and they haven't been wi-fi friendly.
2. Does starting with a B/G router at the modem mean the N routers will revert to B/G?
View 9 Replies
View Related
Jan 25, 2012
I have a simple configuration. E2500 using 2.x ghz N-only configuration. The router in in my office. I want to extend the same network ssid by adding another router in the kitchen, on the other side of the house. I haven't purchased the other router yet
View 1 Replies
View Related
May 1, 2012
I have a E2500 connected to a cable modem as the base of my home network. Hard wire connected to the E2500 is an linksys 8 port hub and a couple of computers. The 8 port hub is connected to a couple of computers and a xbox. I have the hub as a distro point to cut down on wiring. Wirelessly connected to the E2500 are a variety of laptops, netbooks, ipods, an ipad, a playbook, an iphone, a android phone, a wireless printer and a Ps3. Most of the devices are just using the wifi for internet access. Most devices have been setup with their own ip addresses to avoid ip conflicts. The computers and laptops/netbooks are running either Windows XP, Windows 7 or Mepis Linux. Up until now everything was going as good as can be expected, all the computers could see each other and most could transfer files between each other except when Windows gets picky.In the last few days no computers can see each other. Windows or Linux.Everything can accsess the internet and wirelessly print still just can't see each other. I reset the E2500. I updated the firmware on the E2500. I installed the Cisco Connect software (just in case I was too stupid too setup a router). Still nothing. I can ping other machines from a command prompt in windows or a terminal in Linux and get a good ping back. In the router setup via a browser I can go to the status page and see other devices on the local network but most are just ipods, ipad, playbook and the wireless printer, If I go to the administration page / diagnostics I can ping other computers and get a good answer. I just can see them from each other. I think I've rebooted every thing at least once. Yes the workgroup names are all the same (workgroup) and yes file sharing is turned on on all computers.
View 3 Replies
View Related
Jan 2, 2012
Switched from a Netgear router to a Cisco E2500 and now my Samsung blue ray won't connect to internet.
It says physical connection established but can't connect to external network.
View 2 Replies
View Related
Mar 8, 2012
In the process of setting-up a E2500 Linksys router, I set-up my secured network which is working fine but also (I do not know how I did this??) set-up the same named network but it is unsecured. How do I delete this unsecured network.Do I need to set-up the router again?
View 4 Replies
View Related
Dec 30, 2012
I currently use a E2500 router for my home network. I have setup the Wireless guest Network for my downstairs Tenant while he is out of work so he can still have some internet. The problem however is that often the guest network will take up 90% of my 55mb/sec bandwidth, leaving none for the primary network. Is there a way for me to Throttle the amount of bandwidth the Guest network can use? Say alot 10mb/sec for Guest access only, and leave the rest for our main network?
View 6 Replies
View Related
May 2, 2012
I'd like to use an E2500 as a wireless access point in my network. My computer is connected to the office network through a Netgear 5 port desktop switch. Would it be easier for me to configure the E2500 from the switch? If so, do I just plug it in there and access it via the 192.168.1.1 IP address to set it up? And lastly, what should disable (DHCP) or setup in the router so the internet functions through it?
View 8 Replies
View Related
Mar 29, 2012
I have a Linksys E2500 router. Is it possible to have one network name for the secured network and a different network name for the Guest network? The thought is to not have the SSID of the secured network broadcast while allowing the SSID of the Guest network to be broadcast. With the convention of simply adding "Guest" to the end of the SSID for the secured network, it defeats the security option of not having the SSID of the secured network broadcast.
View 1 Replies
View Related
Aug 4, 2011
here is what I have:
A) Sonic Wall @ 192.168.1.215
B) Linksys Switch (WRW248G4P) @ 192.168.1.254
C) Linksys Router (WRT160N) @ 192.168.1.202 (Disabled DHCP Server)
D) Linksys Router (E2500) @ 192.168.1.203
E) Windows Server 2003 @ 192.168.1.200
F) There is also a Router @ 192.168.1.201 that runs DD-WRT that has an enabled DHCP Server.
It goes something like this
i) A - B --ETHERNET-- E
ii) A - B --ETHERNET-- C
iii) A - B --FIBER to another building, then ETHERNET -- D
Everything connects to the internet, but (D) on (iii) doesn't allow connection to the server (E). What can I do to make this work?
View 1 Replies
View Related
Dec 6, 2012
I am trying to extend the wireless network at our church beyond a firewall to another area of the builing. We have a cat 5 cable run through the firewall to the other side. I have a brand new Linksys E2500 router. Can I assign an IP to this router and connect it's WAN "Internet" port to one of the ports on the main router that is connected to the cable modem and use it to extend our network?
View 1 Replies
View Related
May 26, 2012
Is it possible to change one's private network name as well as SSID?
View 1 Replies
View Related
Jan 7, 2012
I would replace an old Levelone Router with a Linksys E2500.I have 3 different routed private networks (e.g. 192.168.1.0/24 , 192.168.101.0/24 and 10.0.0.0/24) How can I forward different ports to this 3 different private networks with an E2500.Under "Games&Applications" in the" Portforwarding" menu the first 3 octets of the "to IP-address" are fix and corresponds ever with the LAN ip address of th E2500.
View 4 Replies
View Related
Mar 17, 2012
I have an E2500 router. When I enter 192.168.1.1 as a web address I am asked for a User name and password. When I do not enter anything for user name and put “admin” in password the screen again asks me for the same two things and eventually goes to a 401 message.
When I enter admin in user name and my secure password to allow devises to connect to the network it lets me in. I thought the password to enter the system settings and the one to enter the network are usually separate. When I open the Cisco Connect program and go into the various menus there my “secure” password is written and visible for anyone who clicks it. Is this how it is supposed to work?Also, how do I occasionally change the password to enter into the network.
View 6 Replies
View Related
Dec 14, 2012
I am using Windows 8 and my router is a Linksys E2500, in the Network folder it shows no icon and also I get a error when I right click the device and choose "Network Map" (from what I can tell this feature has been removed from Windows 8.) Both these problems are cause by an outdated Windows 7 driver on the Microsoft Update Catalog (I have Windows 8 configured to download updates/drivers automatically, that's why this installs)The reason there is no icon is because of these entries in the driver INF
[code]....
View 3 Replies
View Related
Jan 14, 2013
I need to configure two VLANs in my home network to separate a server 1 with VM from another part of network with server 2 and wifi clients. Is it possible to keep DHCP server and internet access on E2500 enabled for both vlans? If so, how should I configure ports tagging (variant shown on screen shoot below doesn't work).
View 5 Replies
View Related
May 11, 2012
I have just bought a Linksys E2500 Router and have been asked for the security key to connect to the Internet. Where do I find it and why is this so well hidden?
View 1 Replies
View Related
Oct 20, 2012
Just installed Linksys E2500 router connected to my Desktop and Cable Modem and access the internet fine. My kindle accesses it and the internet fine. My laptop running Vista connects nicely but only has local access. I find the network and connection area where it sees a network with local only access. I have no clue how to go about changing that. I have the correct password because my Kindle asked me. My laptop does not ask for the password.
View 3 Replies
View Related
Aug 13, 2012
Since the secondary router WRT300N uses the same default IP 192.168.1.1 as the primary installed router EA4500, any attempt to log onto the set up page results in diversion to the Cisco Connect Cloud for the primary router.
Is there a way to access the set up page for the secondary WRT300N, bypassing the main router intervention via the Cloud software?
View 3 Replies
View Related
Aug 21, 2011
I have a set up for cable modem internet i would like to share with a laptop.Its a Motorola surfboard cable modem hooked up to my IBM P4 computer through a USB cable. The Ethernet port out of the modem is NOT operational.The IBM computer gets the internet fine in this configuration. I would like to use a SRX200 WiFi router to connect a laptop to my internet using ICS and leaving the IBM computer and router on when i do this.I opened properties on the USB connection and clicked share internet connection.This then set up my Ethernet port to 192.168.0.1.I now want to connect the SRX 200 to the Ethernet port. Its IP is 192.168.1.1.so, do i connect the computers Ethernet port to one the routers Ethernet ports instead of the wan port?Do i turn off the routers DHCP? Do i have to change the routers IP address to make this work? Will i have to assign fixed IP's to my client to make it work?
View 1 Replies
View Related
Aug 1, 2011
I currently have my wired cable internet hooked into my wrt310n. I have that hooked into a linksys 10/100 ef3124 switch. From there, I have cat5 run to the back of my house, where the wireless signal is weakest. I've got an E2000 router and would like to hook that in at the back of the house. What settings do I need to make in order to set up a completely new wireless network in the back of the house?
View 1 Replies
View Related
Mar 25, 2009
I Installed the DD-WRT firmware on my linksys WRT54G2 v1 router....ibut now the connection keeps on dropping...not stable, how do I roll back to the original linksys firmware?
View 9 Replies
View Related
Jan 23, 2008
I have the wireless-n wrt150n router. I have it wired to my computer and have it wirelessly connected to my ps3. But for some reason there is another unnamed device listed under My Network. My network was not secure before, but I changed it to secure when I noticed the unnamed device. How do I remove that unnamed device from my network?
View 3 Replies
View Related
Sep 24, 2012
I have a Linksys E3000 and I see the gateway (192.168.1.1) listed in my DNS server addresses.
1. Why is this listed here in the DNS?
2. How do I remove it from my DNS servers or stop the router from inserting it into my DNS server list?
View 4 Replies
View Related
May 23, 2009
My Linksys WRT150N recently gave up on me and started to give me weird issues and started to disconnect (all the ports including wired & wireless) anywhere from 3 to infinite number of times per day and my only solution was to remove the power chord and connect it. I tried all possible ways possible including resetting the router, stopping SSID broadcast, removing the encryption, etc, but non worked. As the router was out of warranty my only option was to take it to the dealers where they told me it would take 3 weeks to fix and God knows how much they would have charged me. But after flashing the firmware with the dd-wrt it has been almost 24 hours without a single problem and now I have the cool option of seeing who is connected to the router, etc. This is a MUST for every Linksys owner.
1. Reset the router using 30-30-30 and waited for 2 minutes for things to come back 2 normal
2. Flashed the router with "dd-wrt.v24_mini_generic.bin"
3. Reset again using 30-30-30 and wait again4. Flashed the router with " dd-wrt.v24_std_generic.bin"5.
View 3 Replies
View Related
Sep 5, 2011
I'm currently setting the MAC address filtering for my Linksys E2500 router. I have about 20 devices which i'm allowing to access my router, so i keyed in the MAC addresses into the config page and save setting. But only 16 addresses are registered, the rest refused to register no matter how many times i key in, it just reset back to 00:00:00:00:00:00 after i click on save setting.
View 4 Replies
View Related
Jan 25, 2011
I've been noticing a Belkin router on my network for a while now and just yesterday another Linksys router as join the party, causing havoc on my connection speed!
The strange thing is that I'm the only one seeing them through Norton on my laptop, all other computer on my home network is not detecting them. could this mean that someone is monitoring me? is possible? If I move permanently to Ubuntu linux would the problem go away? OR will they still be able to connect and monitor me?
View 6 Replies
View Related
Oct 4, 2012
I previously entered in settings for the "Static DNS" 1 through 3 (using ip addresses from OpenDNS and one from Google DNS).
I want to remove these so the router reverts to using the DNS allocated to it by the ADSL modem (which will likely be the IP of the modem, which then forwards the requests to the DNS from the ISP).But I can't clear the Static DNS settings. I have to put in 0.0.0.0 but the last zero is not accessed. I get the error: The value is out of range [1 - 254].So I end up with 0.0.0.1 and then all Internet access is lost on the computers because they are being given a bad DNS IP.
How can I reset the static DNS ip address back to 0.0.0.0 ?
View 4 Replies
View Related
Jan 30, 2013
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled) 2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the samesubnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it
View 4 Replies
View Related
Feb 28, 2013
I am trying to connect to a new VPN using my E2500 router. As soon as I connect, the connection breaks.
View 1 Replies
View Related
Sep 3, 2012
i buy a new e2500 from staples. but when i try to register the product. it shows me "Serial Number you entered is invalid.". i am sure i choose the right product and number to register.. so is that mean some one used it..
View 3 Replies
View Related
Dec 18, 2012
I want to add my E2500 as a second wireless router to cover my entire house.I have a Motorola Surfboard SBG6580 cable modem (Time-Warner) at one end of the house.I added via powerline Ethernet connection a new E2500 wireless router at the other end of the house.The E2500 set-up with all defaults and has the same SSID and Password as the Surfboard cable modem.It seems to work OK, but I wonder about network confusion/interference.Do I have to configure the E2500 in some manner to allow seamless roaming of my wireless devices (iPad, Cell Phones, Netbook)?I had an RE1000 with just the Surfboard, but it did not quite do the trick, and does not like both routers connected at either end.
View 9 Replies
View Related
Nov 23, 2011
How To Reset E2500 Router
View 1 Replies
View Related
