Single SSID For Primary And Secondary DD-WRT Wireless Router
Feb 22, 2013
I have more than 5000 sq. ft home and have some dead places other end of the house. Now I am looking for Range Extender/Repeater to boost signal. My primary wireless router is Motorola Surfboard SBG6580 and Secondary Linksys E3000 (planning to update firmware to DD-WRT). So I wanted something such that I can roam between the two routers without switching SSID (use single SSID name for primary and secondary DD-WRT routers) and connect automatically to whichever the best signal (or) strength router. In work place we have same thing like that single wireless SSID name which automatically connect wireless SSID from one end to another end of the building.
View 1 Replies
ADVERTISEMENT
Apr 25, 2011
I have been having problems when trying to host servers on games, etc.I have 2 routers. A modem router, which is a Thomson router. That is the main one. It has a wire connecting from it, to a D-Link router that is near my Computer, and my brother's one. Then that D-Link router has 2 wires from each port, to mine, and my brother's computer.So, I am trying to host games.I didn't connect to the Thomson one, which is also wireless. I am connected to the wired one (D-Link). When I try to host while connected to it, my brother, and other people can't find the server. My brother and me can find it on LAN, but not Internet.But when I disconnect from the Wired, and connect to the Thomson wireless one, and then when I host, I can find it on INTERNET. Even my brother can. He can connect to it perfectly.
I do not want to connect to the wireless, because then it will cause lag spikes every 5 minutes.So, when I disconnect from the wireless, and connect to the wire, I went into the CMD, and typed in ipconfig. I found out that the Default Gteway is the D-Link IP.When I connect to the wireless, and disconnect the wired, I went into CMD, and then the Default Gateway is the Thomson one, which is the main router.So what I want to do, is use the D-Link router, and that router will have the same IP as my thomson one, so that I can host perfectly with no lag spikes, and using a wired connection.
View 19 Replies
View Related
Jun 22, 2011
How can you figure out your primary and secondary DNS? I have a linksys router, and i'm trying to figure out what my primary and secondary DNS are so i can hook up my PS3 online.
View 1 Replies
View Related
Jan 22, 2012
I have a question about the number of Cisco licenses needed in two cases for ACS 5.3 Virtual Machine.One primary + One secondary : Just one license for all or one license for the primary + another one for the secondary ?One primary + several secondaries : Just one license for all or one license for the primary + just one license for all the secondaries ?
View 1 Replies
View Related
Jun 16, 2011
it is possible de use two servers ACS 5.2 (primary and secondary) in active/ active? or just in active/ passive?
View 3 Replies
View Related
Jun 11, 2012
Today I ran a failover test between our primary and secondary ACS systems (ran 'acs stop' on the primary) and in the process decided to promote the secondary while I had the primary down. All was fine until I brought the primary back up and tried to re-register the secondary to it. I get the following error message: I went into System Administration >Operations >Distributed System Management on each and it showed the other device as deregestered, tried to promote from there but it failed too, so I deleted them and tried to register the secondary again. After that didn't work I tried rebooting both but that didn't work either. I know the user/pass I'm using is good and I've tried using both the IP address and the hostname.
ACS/admin# sh app version acs
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.3.0.40.5Internal Build ID : B.839Patches :5-3-0-40-5
View 3 Replies
View Related
Jun 19, 2012
We are trying to configure vrf aware GET VPN with COOP having primary and secondary key servers and also 3 GM routers. All GM routers we use are Cisco 888 and Key servers we use cisco 2911 routers. All GMs crypto maps have been applied into Vlan interface as there's no L3 interface on 888 routers.
Always members can form a tunnel with primary KS, we have configured redundancy with secondary key server and listed on each GM primary and secondary KS on GDOI group.
The issue we facing is that whenever we shutdown the primary or secondary servers the tunnel is not forming with available KS unless otherwise we mannually clear the crypto session. In another way when primary KS down it doest not fall back to secondary KS and no GM get registered. We have already played with all the timers such as DPD, SA lifetimes, GDOI rekey lifetime etc and also exchanging the keys (import/export) with KS and COOPs but there's no luck. We could see the following message was seen on both KS.
[code] 192.168.1.3 is the primary KS and 192.168.1.6 is the secondary KS.I captured attached debug output from 1 GM and secondary KS while I shutdonw the primary KS and also attached is our senario we were trying get work.
Also attached is the show output from both KSs when it form a tunnel with GM.
View 2 Replies
View Related
Dec 5, 2011
We have 2 ASA 5505s in a data center at a remote site.
Whilst troubleshooting another issue I noticed the below. I don't know much about fail over but this would suggest that the secondary ASA is active and the primary ASA is on standby.
if the primary is "active" then how come the secondary is the active ASA? I would have thought that once the primary ASA became active this would assume the "main" role".
[Code] .....
View 7 Replies
View Related
May 15, 2013
Management purchased a HA package from Cisco consisting of 2 5508's with pre installed 500 users license on the Primary WLC and none on the secondary WLC. We have 5508's already so I am familiar with setting them up and so forth. What I am not familiar with is setting them up using HA for failover and license sharing. I've looked and looked and can't find documentation online showing how to set this up. I have found some but nothing that is complete. I have spent 2 days spinning my wheels.
View 2 Replies
View Related
Apr 21, 2013
I have a couple of ACS 5.2 configured as active and backup and I am doing dot 1x authentication using these servers . I have configured the switch with the bellow configuration.
radius-server host 10.0.10.15 auth-port 1645 acct-port 1646
radius-server host 10.0.10.16 auth-port 1645 acct-port 1646
radius-server key 7 aaaaaaaaaaaaaa
please help to understand what will happen in switch
1) in case of primary failure
2)in case if primary returns alive .
View 8 Replies
View Related
Aug 9, 2011
IP address of Primary had to be changed, to respond to a hardware failure of TACACS server with IP in many device configs.
Now the Secondary fails to respond to repeated "Deregister from Primary" requests, even after reload - apparently because it cannot reach the Primary at its old IP address.
Requesting Deregister in GUI generates pop-up that says, "This operation will deregister this ACS Instance from the Primary Instance. Management applications on this ACS instance will be restarted and you will be required to login again. After performing this operation
[code]....
View 1 Replies
View Related
Nov 2, 2011
Cisco ACS 5.2 secondary server is configured as a log collector for both primary and secondary server .Now i am facing problem in log collection from primary server .ACS secondary server is not collecting any logs from primary .
View 2 Replies
View Related
Apr 12, 2011
I have a pair of ASA5520s in active/active failover - this works fine. Both primary and secondary ASAs are running 8.2(2) code.I have a 30-day temp 50 seat SSL license that I applied to the primary. I then started having problems with L2L tunnels.
I noted that if the 'show crypto isakmp sa' state for an L2L was MM_STANDBY, then the remote protected net could not reach my side. However, I could ping across to the other side at which time the state changed to MM_ACTIVE as I would expect and the remote could then reach my side.
I believe this results from the differences between the two licenses. When I applied the 50 seat SSL lic. it disabled failover, but I was willing to risk that for a few days to do show my customer the benifits of SSL connectivity. Note license differences. Is this causing the MM_STANDBY IKE issue and if so can I overcome it and use the 50 SSL VPN Peers lic.
[code]...
View 3 Replies
View Related
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
May 11, 2012
I have recently configured secondary ip address on LAN Interface of Cisco C6509.. We have some application which needs to use broadcast traffic communication to communicate with client... Broadcast is working within subnet & also working from broadcast server to primary subnet. But not working from secondary subnet.. I have checked broadcast within secondary IP range & it's working fine... Secondary not working broadcast with primary and also with broadcast server... broadcast address is different for these subnet but both should be communicate since configured on same interface... When I went through Cisco website found that command "ip directed broadcast" which will pass broadcast to different subnet... But I'm not sure whether any other impact if I enable that command on particular Ethernet interface...
View 6 Replies
View Related
Aug 25, 2011
Cisco ASA 5505 Security Plus 1 link with PPOE dialup for internet access
desirable situation: Primary link with a PPOE dialup Secondary Link with DHCP address Asignment
Problem: i want to configure Dual ISP Failover modus, but the problem exist when i configure the ip sla syntax it looks good in the running config. but after a reload the secondary line becomes primary
It looks like the ppoe client authentication is busy when the ip sla tracking mechanism becomes active. can i tweak the settings that the ip sla tracking mechanism starts later?
What i the correct config for Dual ISP setup with primary PPOE and secondary DHCP
View 1 Replies
View Related
Jan 7, 2013
We an 887m router in our office with an unmanaged switch. We have two networks, 192.168.0.x and 192.168.11.x connected to router on the same interface (192.168.11.253 is a secondary ip) but I can seem to be able to route packets from one network to the other. Internet traffic is fine from both networks. I can't see what I'm doing wrong here. I can ping the 192.168.11.253 (router) from the 192.168.0 network but nothing beyond that.
I tried this at home with no other config and its the same. Is this by design?
View 4 Replies
View Related
Mar 17, 2013
I want to Single SSID in my network .I have 3 cisco 4410 WAP. ISP router Have the Wireless .How to get the single ssid in the network .same time i want to do configure in the isp router for wireless?
View 1 Replies
View Related
Jul 16, 2012
I am setting up a Cisco 5508 wireless controller and was looking for some feedback or assistance. Basically I already have my guest SSID configured and functioning. Created an interface group containing my vlans and applied the created ACL "Guest Policy - internet only", which is also working.I want to setup a second SSID called "staffstudent" and use RADIUS for authentication. I have already created two separate network policies on the radius server: staff and student. Each only allows certain user groups. I want to be able to differentiate on the controller side which profile they are logging in on and then apply the correct ACL. I have two currently configured: one for staff and one for student. It appears to me that since you have to apply the ACL at the interface level I cannot use both since my interface is accepting both staff and students. Is there a way I can filter them using RADIUS so that when they login RADIUS can return a "student" value and then apply the correct ACL? Same for staff?
View 2 Replies
View Related
Oct 12, 2011
I have two 1142n LWP ap converted into standalone, as client doesn't have any controller there. They just want to extend their network via wireless.
L3 switch (trunk port gig 1/48) -----> connected to AP1
L3 switch (trunk port 2/48) -----------> connected to AP2
client is looking for 3 vlans on the floor ( users might multiple vlans might associated same AP ). They have a dedicated DHCP/DNS server and he will be configuring 3 vlans on L3 switch with correct ip helper address on SVI interfaces.
I'm i allowed to created 3 SSID's on 1142n standalone AP ?
What would the various optiosn to achieve this requirement ? Is there any simplest way to achieve this ? Do i need to go for 802.1x ? I remember client told their users are authenticating by using AD for wired network. This is their first request for wireless environment
View 2 Replies
View Related
Apr 2, 2013
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
View 16 Replies
View Related
Dec 27, 2012
We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies
View Related
Aug 1, 2011
I currently have my wired cable internet hooked into my wrt310n. I have that hooked into a linksys 10/100 ef3124 switch. From there, I have cat5 run to the back of my house, where the wireless signal is weakest. I've got an E2000 router and would like to hook that in at the back of the house. What settings do I need to make in order to set up a completely new wireless network in the back of the house?
View 1 Replies
View Related
Aug 13, 2012
Since the secondary router WRT300N uses the same default IP 192.168.1.1 as the primary installed router EA4500, any attempt to log onto the set up page results in diversion to the Cisco Connect Cloud for the primary router.
Is there a way to access the set up page for the secondary WRT300N, bypassing the main router intervention via the Cloud software?
View 3 Replies
View Related
Feb 25, 2013
Region : Argentina
Model : TL-WDR4300
Hardware Version : V1
Firmware Version :
ISP : fullrate.dk
My ISP has provided me a router: Zyxel P-2601HN which has an ideal WLAN transfer rate of 150 mbps. I live in a concrete 2 story house so signals are weak at best on the other floor - therefore, I Have bought the TL-WDR4300 as an extension for the latter floor. I have connected the routers from LAN to LAN and the Zyxel has 192.168.1.1 on LAN and the TL-WDR4300 had 192.168.0.1 as out set. I have changed this to 192.168.1.2 and all the setup (disabled DHCP + other) seems to work alright. BUT i can not log into the TL-WDR4300 !! Not with http://192.168.1.2 and not with [URL]. What I can do to get into the setup of TL-WDR4300. I know I can alays backup the setting and reset the router and load the setting again, make alterations, saving .....but it kind of drastic !Can the two radios SSID names (2,4 MHz and 5 MHz) be the same name as the SSID name on the Zyxel P-2601HN ? What are the implications ?
View 3 Replies
View Related
Aug 21, 2011
I have a set up for cable modem internet i would like to share with a laptop.Its a Motorola surfboard cable modem hooked up to my IBM P4 computer through a USB cable. The Ethernet port out of the modem is NOT operational.The IBM computer gets the internet fine in this configuration. I would like to use a SRX200 WiFi router to connect a laptop to my internet using ICS and leaving the IBM computer and router on when i do this.I opened properties on the USB connection and clicked share internet connection.This then set up my Ethernet port to 192.168.0.1.I now want to connect the SRX 200 to the Ethernet port. Its IP is 192.168.1.1.so, do i connect the computers Ethernet port to one the routers Ethernet ports instead of the wan port?Do i turn off the routers DHCP? Do i have to change the routers IP address to make this work? Will i have to assign fixed IP's to my client to make it work?
View 1 Replies
View Related
May 11, 2012
I set up a linksys e2500 router with name "mynetwork" and WPA2 password.
The network works fine, my laptop connects securely to it.
But when I View Available Wireless Networks , I see a second , unsecure network named "mynetwork-guest" to which my laptop will also connect with no credentials (not sure how that network got there).
How can I find and delete that unsecure network? When I go into my router setup, I only see mynetwork, not mynetwork-guest If it is of any use here is the IP information for both:
The settingd for mynetwork:
IP Address: 192.168.1.133
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
The setting for mynetwork-guest:
IP Address: 192.168.33.137
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.33.1
View 2 Replies
View Related
Nov 14, 2011
My network is Cable modem -> RVS4000 (does my VPN) -> E3000 (does my wireless)Cisco connect seem to deal with this issue and I want to use the guest feature of the wireless.
View 1 Replies
View Related
Mar 6, 2011
I named my network "abc," and the system appends "-guest" to it, i.e.., "ABC-guest", to use as the guest network name. I want to hide the name of the primary/private network completely. Why can't I do that? I know I can use a different password.
View 7 Replies
View Related
Nov 24, 2012
The router always inserts its’ own address as the primary DNS server for the all DHCP clients even though you have set the DHCP server on the router to assign manual external addresses?
Oh I have a
WRT310n v2
firmware v2.0.01 build 004
Let me elaborate a little so I am clear what I am saying. On the router setup page go to the section that is labeled “DHCP server settings” enter 3 static DNS servers. Say 2 Google and one open dns.
8.8.8.8
8.8.4.4
208.67.222.222
Apply your settings.
Release your ip on your workstation, then renew it. And look at your DNS, the routers address is still the first entry.
DNS Servers . . . . . . . . . . . : 192.168.1.1
I suspect this was probably a design decision so that they could allow a user to open their web browser and type something neat like [URL]. Which for the average user is fine and dandy. If my ISP didn’t suck and try to redirect everything to cached copies I probably wouldn’t have noticed it. But since I end up using the router for DNS and it picks up DNS from my ISP I end up getting Akamai IP addresses, and they have problems with SSL certs…. So you get errors.
I know I can go set the DNS server settings on the workstations. But I really don’t want to do this on all of my devices as they are mobile and switch networks, and on some networks not using the local dns breaks things. Like on the corporate network.
View 5 Replies
View Related
Jun 4, 2012
When I plug my desktop into my wireless router I have slow internet but when I plug directly into the modem I have no connection at all. It says "cannot connect to primary DNS server". I'm using a Motorola SURBOARD SB6121 and a NETGEAR WPN824V2 Wireless Router. When I do ipconig /all this is what I get:
View 11 Replies
View Related
Dec 4, 2012
Region : UnitedStates
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
ISP :
My TL-WR700N does its job to provide wired internet to my desktop computer from another wireless router via client mode. However, when it is connected, the other wireless clients connected to the primary router lose their connections. To restore those connections, the WR700N must be powered down and the primary router must be restarted.
View 4 Replies
View Related
Sep 25, 2012
I am using D link DIR 615 router for my network. My ISP sent me a letter few days ago that they can provide me total separate wireless connection other than my regular connection. But they will charge me $10/month for this. just wondering do we have any way to create two separate wireless network so that my clients can access that free wireless connection when they are in my store. But on the other side they don't interfere with my regular connection and its good for my network security too.
View 8 Replies
View Related
