I want to Single SSID in my network .I have 3 cisco 4410 WAP. ISP router Have the Wireless .How to get the single ssid in the network .same time i want to do configure in the isp router for wireless?
View 1 Replies
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
I am setting up a Cisco 5508 wireless controller and was looking for some feedback or assistance. Basically I already have my guest SSID configured and functioning. Created an interface group containing my vlans and applied the created ACL "Guest Policy - internet only", which is also working.I want to setup a second SSID called "staffstudent" and use RADIUS for authentication. I have already created two separate network policies on the radius server: staff and student. Each only allows certain user groups. I want to be able to differentiate on the controller side which profile they are logging in on and then apply the correct ACL. I have two currently configured: one for staff and one for student. It appears to me that since you have to apply the ACL at the interface level I cannot use both since my interface is accepting both staff and students. Is there a way I can filter them using RADIUS so that when they login RADIUS can return a "student" value and then apply the correct ACL? Same for staff?
View 2 Replies View RelatedI have more than 5000 sq. ft home and have some dead places other end of the house. Now I am looking for Range Extender/Repeater to boost signal. My primary wireless router is Motorola Surfboard SBG6580 and Secondary Linksys E3000 (planning to update firmware to DD-WRT). So I wanted something such that I can roam between the two routers without switching SSID (use single SSID name for primary and secondary DD-WRT routers) and connect automatically to whichever the best signal (or) strength router. In work place we have same thing like that single wireless SSID name which automatically connect wireless SSID from one end to another end of the building.
View 1 Replies View RelatedI have two 1142n LWP ap converted into standalone, as client doesn't have any controller there. They just want to extend their network via wireless.
L3 switch (trunk port gig 1/48) -----> connected to AP1
L3 switch (trunk port 2/48) -----------> connected to AP2
client is looking for 3 vlans on the floor ( users might multiple vlans might associated same AP ). They have a dedicated DHCP/DNS server and he will be configuring 3 vlans on L3 switch with correct ip helper address on SVI interfaces.
I'm i allowed to created 3 SSID's on 1142n standalone AP ?
What would the various optiosn to achieve this requirement ? Is there any simplest way to achieve this ? Do i need to go for 802.1x ? I remember client told their users are authenticating by using AD for wired network. This is their first request for wireless environment
I have around 60 , 1142 N APs . As of now i have only management VLAN ( for IP ) & one user vlan 350 configured on the access point . All the users connect to VLAN 350 and they get IP as required.However in our new set up there are couple of requirements have come up were in SSID will be the same however we have created many VLANs for different kind of user group and all these VLANs should be mapped to this single SSID and pick the IPs from their respective VLANs .
We have done configuration on the RADIUS server side were in we have mapped the users in their respective VLANs and they are getting authenticated via AD . Now how do i map my these 4-5 VLANs in a single SSID in Access Point.
I have spent countless weekends trying to configure the WAP 4410 as a wireless repeater. From what I see the instructions and help screens seem to be incomplete or the WAP is not capable of this function even though it is available.It will not connect to the modem wirelessly as a repeater. I have tried numberous settings including the same channel and SSID without avail. As soon as I disconnect it from the wireless modem it will no longer connect to the internet.I have an older WRT 610N which will connect to the modem as a repeater so I don't think it is at the modem end.Searches have indicated others with a similar problem but I don't see any viable solutions except to buy and connect to another WAP 4410.Contacting Cisco for suppor by chat t has been pointless. Either they are not available when I am or they are clueless.
View 5 Replies View RelatedI have 5 access points (WAP4410N) all connected to a befsr41 8 port/switch router, each AP has it's own SSID. Is it possible to to have one SSID for the entire wireless network so users do not have to change SSID's every time they change locations?
View 11 Replies View RelatedWe have 4 access points in my network i want configure 1 is ap mode another 3 is bridge mode Is it possible to configure in 4410 N ? if i configure bridge mode can i use single SSID&Securtiy key for all aps. how to i use these 4 access points
View 1 Replies View RelatedWe have a WLC 4410 management IP Address configured as 10.40.124.59.and configured VLAN1 on WLC with IP address 10.40.126.250. we are unable to ping the VLAN1 ip address from the switch. even unable to ping 10.40.126.252 (Gateway). Is there any limitation that we can not configured ip address from secondary scope...Switch vlan 1 configuration is ......interface GigabitEthernet0/0.1description Business VLANencapsulation dot1Q 1 nativeip address 100.93.50.2 255.255.0.0 secondaryip address 10.40.126.252 255.255.255.0 secondaryip address 10.40.124.61 255.255.255.192 secondaryip address100.43.94.252 255.255.255.0.
View 3 Replies View RelatedDoes LMS 4.1 or any newer version support Cisco Access Point 4410 N ?
View 1 Replies View RelatedHow do i get into my ssid the wireless network is got my name on it
View 1 Replies View RelatedWireless Equipment
D-link DIR-655 router set to only N
Old Netgear Router used as access point set to only G (I set up as an access point by turning off DHCP, changing the IP adresss and set to only G.)
Wireless Printer (only G Capable)
Cell Phone (only G Capable)
2 Laptops (both N capable)
iPad (N Capable)
Roku Media Box (N capable)
Problem: If I put the router and access point on the same SSID then equipment that is N capable will connect to the G network.If I use two different SSID's then the printer is unreachable.Is there a way of either (a) having two SSID's but allow the printer to be seen or (b) having one SSID, with separate access points for N and G but not allow N functioning client to connect to the G access point.
I am using D link DIR 615 router for my network. My ISP sent me a letter few days ago that they can provide me total separate wireless connection other than my regular connection. But they will charge me $10/month for this. just wondering do we have any way to create two separate wireless network so that my clients can access that free wireless connection when they are in my store. But on the other side they don't interfere with my regular connection and its good for my network security too.
View 8 Replies View RelatedSeveral days ago I had to change my router. The new one works OK except that I can't get the PC to link into the wireless while the SSID isn't being broadcast. Having read that it is a good idea not to broadcast the SSID for security reasons, I thought I would try it!
I am running Windows 7 home Premium and the router is a Draytek Vigor 2710 using WPA2. I can see the network when the SSID isn't being broadcast, it just refuses to connect to it. As soon as I switch on the SSID it connects like a dream.
As the title states, I am want to set up a single ADSL connection, using 1 router across 6 apartments. The apartments are 2 floors and from the top they look like this The Router is on Apartment 1. Between apartment 1 and 2, 3 and 4, and 5 and 6 is a normal cement wall. Between 3 and 4 is Cement and stone, so are the outside walls of each house. I was thinking of doing it simple and using 3-4 range extenders such as the Linksys RE1000. From what i searched on the internet, and what the documentation states, the signal will get bottle-necked for the last house due to the RE1000 giving half of the bandwidth. Quote from Linksys FAQ: Quote: 7. Can I add more than one RE1000 to my existing wireless network? Yes. But since the RE1000 only gets half of the wireless signal from your main router or access point, adding multiple range extenders can provide you with even lower signal, thus, giving lesser bandwidth to your wireless computers or devices that you are going to connect to these additional extenders.So, what would be an optimal solution to this? Should I go ahead and install the RE1000's? Is there something better that i can do?
View 5 Replies View RelatedWe have recently aquired a remote location which has a pre-existing flat network (172.16.X.X/16). Before we are able to convert them over to our new IP scheme, they have a need to have wireless connectivity on site. We have 4 1142's which I need to configure for them. I have experience configuring WLC's and autonomous AP's for networks with multiple vlans but have never configured AP's for a flat, single subnet network. I need to configure them for either guest access (internet only) or corporate access to network resources with radius authentication. Do I configure a native vlan as I would for a typical multi vlan network? Do I configure the switch port as an access port as opposed to a trunk beacause of the lack of layer 3? I basically need a sample configuration for this situation.
View 1 Replies View RelatedI'd like to change the SSID name on Aironet 1200 which is currenty used by my wireless network.
View 3 Replies View RelatedI have a simple configuration. E2500 using 2.x ghz N-only configuration. The router in in my office. I want to extend the same network ssid by adding another router in the kitchen, on the other side of the house. I haven't purchased the other router yet
View 1 Replies View Relatedjust bought the EA4500 new, setup the router with computer plug-in RJ45, after I change my network network to "LinksysOne", I can connect to the network wireless. But when I connect it with hard wire/RJ45, it shows "cisco27205", but I cannot see "cisco27205" with wifi, neither with RJ45 connection cannot see "LinksysOne". Why this happen? is this normal?
View 1 Replies View Relatedi have a linsys wrt54g router. my main computer is connected (wired) and works fine. until today my wireless devices were able to connect and access the internet using the router. now the ssid does not show as a possible network connection. i have unplugged everything, rest the router, checked setting, shutdown and reset every computer and all my wireless devices still cant locate the network connection???
View 9 Replies View RelatedI have a wrt160n router set up at a friends house that i would connect my windows xp laptor to when i would go there. it always worked fine. i recently got a new laptop with vista 64 bit OS. i went to my friends today and connected via wireless for the first time. i expected to get prompted for the security key. instead it asked for the pin #. the pin number was something new i noticed when i replaced an older linksys with the new wrt160n so i had it in my notes. i entered the pin number and connected to the wireless router. but then my friend laptop could not connect and said it couldnt find the network. when i viewed the available networks, i noticed that the original network SSID had been changed to my vista laptop's computer name. i had to physically connect my laptop to the router and reconfigure the settings of the wireless network. then my friend was able to see the available network and automatically connect..
View 6 Replies View RelatedIs it possible to change one's private network name as well as SSID?
View 1 Replies View Relatedi have a e3000 set up with my network i have guest network set up through the cisco connect but dont see a field to change the guest network broadcast ssid so an ideas?
View 1 Replies View Relatedi have two LAN 1:=IP10.44.0.76 subnet:255.255.255.0 & gateway: 10.44.0.1 ; 2:=IP DHCP,i want to do work both network. how can its possible.
View 3 Replies View Related
I've 4 ISP in my office. In my network all the machines are connected through unmanaged switches.Now if I need to shift any one machine to other ISP then I need to change his IP.Is the following possible:
I connect all the four ISP's to a machine(say Server), then I take out a wire and connect it to the switch so that I can distribute all the ISP into the network.Now on the basis of the MAC Address I can change the assign any ISP to any of the other machine in the network.Also is it possible that I can monitor their data usage as well as can CAP there bandwidth.
My brother is using an insane amount of bandwidth, and being from Australia, we don't get very much unless we want to pay very much
View 5 Replies View Relatedi have configured my network like below:
I have three lan ports in my server the IP is:
(1) IP: 10.10.10.2 SUBNET: 255.255.255.224
(2) IP: 10.10.10.34 SUBNET: 255.255.255.224
(3) IP: 10.10.10.69 SUBNET: 255.255.255.224
I have given IP as mentioned below to 1 to 30 pc connected in First Switch.
IP Starts From : 10.10.10.5 To IP : 10.10.10.30
Subnet Mask: 255.255.255.224
Gateway: 10.10.10.2
For 31 to 50 Pc in Second Switch
IP Starts From : 10.10.10.40 To IP : 10.10.10.65
Subnet Mask: 255.255.255.224
Gateway: 10.10.10.34
IP Starts From : 10.10.10.74 To IP : 10.10.10.85
Subnet Mask: 255.255.255.224
Gateway: 10.10.10.69
Pc are connected internally in separate switch. but can not connect all three switches & with server. Only Gateway 10.10.10.69 is connected with server.
How do I add a network SSID from/for a tablet
View 1 Replies View RelatedI am in the process of acquiring a static ip address from my isp time Warner. I only want to pay for a single static, but I have a number of machines I want to put on the internet, a web server and a e-mail-server. Using a cisco router, a Cisco Rv 120w. Can I assign the static ip address my isp gave me to the Rv 120w and then crate a vlan to assign addresses to various computers. Or is this something my ISP does. I get the impression from the tech guy at Time Warner that this is something they do.
View 11 Replies View Relatedhaving problems with a slow network at work.. ive just become resonsible for the network and inherited a lot of ancient kit.upstairs we have a switch connected to our router.. downstairs we have 2 ancient hubs, daisychained and with 30 devices connected via cat5 and cat5e cable.the question is, if i get the cabling cut, recrimped and all of the cabling connected to the single switch instead of the 2 hubs is there any reason for it not to work, or for performance to be worse?
View 10 Replies View RelatedI have 2 gateway over my network provider to connect to internet.like Gateway1="1.1.1.2" and Gateway2 = "1.1.1.3".but i have only one network adapter with one wire.now i want program to create "Virtual Network adapter" assigned to my real network adapter to set secondary Gateway to it, and use it by "ForceBindip".
View 3 Replies View Relatedi have a BSNL Broadband connection (1st Connection- input via RJ11-telephone line) thru ADSL2 + modem and now i have another Internet connection provided by another ISP(2nd Connection input via DSL - RJ45) thru Asus RT-N10E WireLess router for backup in case 1st ISP fails. now when 1st fails i have to switch to 2nd one manualy.s there a way by which my computer could switch over automatically to 2nd or visa versa to have a seemless connection.2nd issue related to it is that i have my n/w sharedrive and n/w printer connected (Wired) thru 1st Connection. when i switch to 2nd Connection i can only access internet connection but the n/w printer and shared drive are not available.
View 3 Replies View Related
