Cisco Wireless :: 4410 Unable To Ping Secondary IP Scope Gateway
Nov 15, 2012
We have a WLC 4410 management IP Address configured as 10.40.124.59.and configured VLAN1 on WLC with IP address 10.40.126.250. we are unable to ping the VLAN1 ip address from the switch. even unable to ping 10.40.126.252 (Gateway). Is there any limitation that we can not configured ip address from secondary scope...Switch vlan 1 configuration is ......interface GigabitEthernet0/0.1description Business VLANencapsulation dot1Q 1 nativeip address 100.93.50.2 255.255.0.0 secondaryip address 10.40.126.252 255.255.255.0 secondaryip address 10.40.124.61 255.255.255.192 secondaryip address100.43.94.252 255.255.255.0.
View 3 Replies
ADVERTISEMENT
Mar 31, 2011
We have two ASA5510s, each with outside interfaces to the same two ISPs (different IP addresses within the same subnet, of course). Both ASAs allow ICMP on all (inside and outside) interfaces. One ASA's default route is to ISP-1 and the other is to ISP-2. We can ping the default gateways for both ISPs from only one ASA. From the other ASA, we can only ping the default gateway for the default route but not the other. The pings originate from an inside client, first configured with the default gateway for ASA-1, then for ASA-2. Why does this happen, how do I troubleshoot something like this and how do I fix it?
View 1 Replies
View Related
Apr 7, 2013
DHCP scope is configured on a WLC 5508.I'm checking if there' a way for WLC to clear the dhcp leasing when a user is diconnected from wireless?
View 2 Replies
View Related
Oct 24, 2011
about two days ago my main PC lost the ability to connect to the internet. I'm useing a trendnet tew-687ga adapter and a netgear n600 router. I can't ping the default gatway 192.168.1.1
View 2 Replies
View Related
May 30, 2012
I am just setting up a simple scenario with a 1841. Server @ 172.31.1.1 cannot ping 172.31.0.254 or 172.31.0.105. It can ping 172.31.1.250. The router can, on the other hand, ping devices on both networks. This is just for testing routing theory so I don't know why hosts on either side of the network cannot ping each other.
I am only using the FastEthernet interfaces on Router 1841.
View 3 Replies
View Related
Jul 26, 2012
We have a VPN setup between two Cisco RV082 routers, the VPN status shows as connected however I can't ping the other network. I am unable to ping between routers, let alone ping computers behind those routers.
We have 2 branches, branch 1 is on a static IP and branch 2 is Dynamic. I am able to connect via QuickVPN from Branch 2 to Branch 1 and remote desktop to computers, however have yet to VPN/remote desktop in the opposite direction.
To me it seems like a firewall issue at branch 2, but what's causing this. Also they are currently running 2 differnet firmware version not sure if this would cause a problem.
View 1 Replies
View Related
Dec 12, 2011
I set this up and I can ping all the gateways but never the hosts. I was hoping I could make these links between 6500's a mix of L2 and L3. Check it out. They are connected in a linear fashion R1--->R2--->R3. I can ping from R1 to R3's SVI4 gateway but I can never ping a host on that SVI4. I was hoping that I could use the port-channels between 6500's as routed links or as trunk links depending on the type of traffic....thought it would ease the migration. I suppose I could always get rid of the port-channels and just make separate L2 and L3 links between the 6500's.
View 3 Replies
View Related
Jan 15, 2012
Cisco ASA 5505 Cannot Ping Secondary Internal Network.
View 9 Replies
View Related
Sep 21, 2012
I have spent countless weekends trying to configure the WAP 4410 as a wireless repeater. From what I see the instructions and help screens seem to be incomplete or the WAP is not capable of this function even though it is available.It will not connect to the modem wirelessly as a repeater. I have tried numberous settings including the same channel and SSID without avail. As soon as I disconnect it from the wireless modem it will no longer connect to the internet.I have an older WRT 610N which will connect to the modem as a repeater so I don't think it is at the modem end.Searches have indicated others with a similar problem but I don't see any viable solutions except to buy and connect to another WAP 4410.Contacting Cisco for suppor by chat t has been pointless. Either they are not available when I am or they are clueless.
View 5 Replies
View Related
Apr 21, 2012
I have 5 access points (WAP4410N) all connected to a befsr41 8 port/switch router, each AP has it's own SSID. Is it possible to to have one SSID for the entire wireless network so users do not have to change SSID's every time they change locations?
View 11 Replies
View Related
Jun 9, 2012
I'm trying to get a 2811 router with a NM-AIR-WLC6 Wireless Controller Module to work with an c1200 series access point. The LWAP is connected to a 2690 switch which has a trunk connected to the router. My configuration looks very similar to example 2 on this page: [URL] . The LWAP does get an IP from the DHCP pool on the router. I can also connect to the GUI of the controller from a PC on VLAN 250 (which also is connected to the switch).
[URL]
The moment I join my Wireless network I get no IP and when I enter a valid static IP, I still can't ping the gateway. I also noticed that the controller could ping the gateway before I configured the interface. After configuring an interface with that gateway, the controller loses the ability to ping to it. I can't seem to figure out why. I've been working all week on getting this controller and LWAP to broadcast a fully working network.
View 3 Replies
View Related
Jan 29, 2011
I have a wireless system and I am setting up the player but cannot connect because of the gateway ping problem.I called my server and was told that my average ping rate is 1292 and have no hope of getting connected.
View 7 Replies
View Related
Mar 17, 2013
I want to Single SSID in my network .I have 3 cisco 4410 WAP. ISP router Have the Wireless .How to get the single ssid in the network .same time i want to do configure in the isp router for wireless?
View 1 Replies
View Related
Jul 14, 2011
We have 4 access points in my network i want configure 1 is ap mode another 3 is bridge mode Is it possible to configure in 4410 N ? if i configure bridge mode can i use single SSID&Securtiy key for all aps. how to i use these 4 access points
View 1 Replies
View Related
Jun 19, 2012
failed gateway ip ping on dell xps 15r laptop and slows up the internet, but when I plug it into the outlet, ping test passes and the internet screams.
View 9 Replies
View Related
Jul 15, 2012
I have been using this router for the last six months and never had a single problem. Then yesterday out of nowhere internet stopped working and I was not able ping my ISP gateway (both wired and wireless) [Received: Destination host not reachable on both Windows Vista / 7]. Rebooted the router but still no luck. Unplugged / Replugged the net connection from the WAN port and then finally ping was successful.Now the weird this is every time I power on the router the Internet does not work and ISP Gateway seems not reachable, but if I unplug/replug the WAN connection the ping reply starts and internet works without any problem.
View 3 Replies
View Related
Sep 20, 2012
We are using Cisco VPN Client 5.0.07.0290 to connect to our servers. We have Sonicwall NSA2400 FW and we have 2 ISPs. We have configured the Load balancing on Firewall in 'Spill-Over' mode.
So whenever the 1st ISP Line is on full load it will automatically moves the users on 2nd line.The problem we are facing here is users who are getting IP from 1st ISP Line they are smoothly able to connect to Cisco VPN client but the users who are getting IP from 2nd ISP Line they are not able to connect to Cisco VPN Client. This is really annoying as everyone should be able to connect.
View 8 Replies
View Related
Dec 6, 2011
I have installed 2 ACS 5.2 appliances, the two appear as Primary. When I try to register one of them with the other one using "System Administrator -> Local Operation -> Deployment Operations" I get the following message:
This System Failure occurred: Unable to authenticate with node.. Your changes have not been saved.Click OK to return to the list page.
I have tried with both "ACSAdmin" and "admin" users with their respective passwords.
View 3 Replies
View Related
Jun 11, 2012
Today I ran a failover test between our primary and secondary ACS systems (ran 'acs stop' on the primary) and in the process decided to promote the secondary while I had the primary down. All was fine until I brought the primary back up and tried to re-register the secondary to it. I get the following error message: I went into System Administration >Operations >Distributed System Management on each and it showed the other device as deregestered, tried to promote from there but it failed too, so I deleted them and tried to register the secondary again. After that didn't work I tried rebooting both but that didn't work either. I know the user/pass I'm using is good and I've tried using both the IP address and the hostname.
ACS/admin# sh app version acs
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.3.0.40.5Internal Build ID : B.839Patches :5-3-0-40-5
View 3 Replies
View Related
May 21, 2013
My controller is vWLC installed in ESXi which has to vNet Cards configured with all vlans(4095), then it is connected to a 3560 switch with trunk. The configuration of the switch interface is as belows: The SSID is BYOD and I can connect the SSID and get the IP address such as 10.10.10.118/24, but for now, i cannot ping 10.10.10.1, but i can ping 10.10.10.90.
View 3 Replies
View Related
Jan 18, 2013
From My Router that connects to Cable modem i am unable to ping website 4.2.2.2I am able to ping all other websites fines.Same website i can ping from my pc and all other switches fine.Router has only 1 ACL thats for NAT.
View 25 Replies
View Related
Jun 5, 2012
I have an ASA 5510 running v8.4(3)9 and have setup a remote user VPN using the Cisco VPN client v5.0.07.0410 which is working appart from the fact that I cannot access resources on a secondary subnet.The setup is as follows:
-ASA inside interface on 192.168.10.240
-VPN clients on 192.168.254.x
I can access reources on the 192.168.10 subnet but not any other subnets internally, I need to specifically allow access to the 192.168.20 subnet,[code]
View 3 Replies
View Related
Jan 7, 2013
We an 887m router in our office with an unmanaged switch. We have two networks, 192.168.0.x and 192.168.11.x connected to router on the same interface (192.168.11.253 is a secondary ip) but I can seem to be able to route packets from one network to the other. Internet traffic is fine from both networks. I can't see what I'm doing wrong here. I can ping the 192.168.11.253 (router) from the 192.168.0 network but nothing beyond that.
I tried this at home with no other config and its the same. Is this by design?
View 4 Replies
View Related
Feb 13, 2013
i'm having problem to ping succesfully default gateway on Router1 from Router2. Basically i can: - ping from R1 the serial interface on R2 and default gateway on R2 - telnet from R1 to R2 - ping from R2 to serial link on R1, BUT I CANNOT ping default gateway from R2 to R1 Below is the photo showing topology and running configuration on both routers
View 2 Replies
View Related
May 13, 2013
One of our ASA5505 can not ping the gateway today. But when I use a notepad , using the same IPs, it can ping the gateway !!!
It is so strange, the ASA5505 was working ok before until today.
Is there anyting I can do to check whether the ASA is ok ?
View 2 Replies
View Related
Sep 10, 2012
I have a VM server, whose IP is in customer VLAN600 ( 172.60.60.10/24 ) and Peer end is switch then Firewall.Switch is configured with same VLAN600 and learning mac-address of Server on VLAN 600, Firewall is also having VLAN600 and IP is 172.60.60.1/24.Server is not able to Ping/reach Firewall and vice versa.
View 1 Replies
View Related
Aug 29, 2012
Have been given a Dell computer for my daughter, it is only just over a year old and cant get it to connect to internet. It keeps saying that the router is not working, when I know it is ok because my other computers work on the internet ok. When I was looking to see if I could find problem I managed to access something which let me check computer connection and it came up that the Gateway IP Ping failed so I would not be able to connect to internet
View 1 Replies
View Related
Feb 6, 2013
i am using wlc 4402 with a mgt ip 172.26.150.x/24 and ap manager ip 172.26.150.x/24, my all ap get the ip address from dhcp . currently in dhcp server 172.26.150.3 to 254 dhcp scope is configured. at mysite some devices are configured like ipad,iphone or galaxy tab with mac binding in dhcp server. now this pool is almost full. i have a policy configured for these devices for mac binding is done in DHCP. to increase pool what are the changes i need to do in wlc. what are the changes i need to do in dhcp server . is policy made for mac binding in dhcp server will get affected by this ?
View 2 Replies
View Related
Oct 24, 2012
I've spent the last two days working on this problem and it is killing me! I know the answer has to be something simple, but despite hours of searching and trying different things, I just can't seem to fix it.Essentially, I am going to be installing a Cisco 2691 and use it as the default gateway for a small business. It will be directly connected to a cable modem with a static IP. The other Ethernet interface is going to connect to a 2950 switch with a couple different VLANs.
The problem I'm having is that I can ping anything external from the router itself. From the clients connected to the 2950, I can ping IPs in other VLANs, and I can ping up to the IP of the external interface, but no pings go beyond that.I've set up NAT overload on the router, and when I do a debug ip nat, I see the pings trying to get through with the proper translations, but I still don't receive ICMP replies back.I set up GNS3 to simulate what I'm trying to accomplish (since it emulates a 2691). Attached is a jpg of the topology -- on the right is the "simulated ISP" with 3 loopback networks and one host on a different subnet. The 2691 has a static route to the "Internet" router, and can ping everything attached to the router, including the host. The host (5.5.5.5) can also ping the outside interface of the 2691 (50.50.50.2).
However, the hosts behind the 2691 can't ping past 50.50.50.2. The 192.168.0.x network can be ignored, because that network won't need to access the Internet. But the 10.10.20.x (VLAN 20) and 10.10.30.x (VLAN 30) networks will need to. In the simulation, the hosts are 10.10.20.5 and 30.5. They can ping each other, their default gateways, and the 2691 outside interface (50.50.50.2) but not the other side, the "Internet" router at 50.50.50.1 or beyond.
[code]....
View 4 Replies
View Related
Dec 24, 2011
I have more than 10 PC om my Workgroup, using DHCP on network, but I have one PC alwaws got wrong IP (auto from dhcp), and can't connect even using static IP (status connect, but can't ping to gateway and other IP)Here "ipconfig /all" on one of PC that work. [code]
View 5 Replies
View Related
Aug 10, 2011
I have a 5508 WLC controller at the HQ with the employee ssid ,the dhcp scope on the ssid is 10.120.0.0/16 network.
However,I want this same ssid to be brodcasted to a remote site using HREAP access point but with different dhcp scope 10.102.0.0/16.
I have tried creating another interface for the remote site with a different dhcp scope(10.102.0.0) but the controller wont allow me create another wlan with same ssid that existed before to apply the new interface created for.
View 1 Replies
View Related
Feb 16, 2012
I did the config below but unable to obtain the ip from the subnet scope 10.10.9.0. The switch is in the layer 3 mode.
no spanning-tree
vlan database
vlan 2
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
[code]....
View 1 Replies
View Related
Jul 18, 2006
I'm unable to access my linksys wireless g broadband router (WRT54G)'s access gateway. (192.168.1.1)The gateway page doesn't load, at all. It doesn't ask for the user or password at all. On any of my internet browsers (firefox, and internet explorer)Anyway of fixing this would be appropriate.
View 2 Replies
View Related
