DHCP scope is configured on a WLC 5508.I'm checking if there' a way for WLC to clear the dhcp leasing when a user is diconnected from wireless?
View 2 RepliesI've created a tonne of dhcp scopes on my routers before never had any issues, however this one will not hand out any addresses at all, i even give the router a reload to see if any magic happened but nothing, ive ended having to put a temp server in with just dhcp installed until i get the router diong what it should my config below, its something simple i havent seen, as ive compared it to plenty of my working DHCP configs and seen nothing.
View 11 Replies View RelatedI have a 5508 WLC controller at the HQ with the employee ssid ,the dhcp scope on the ssid is 10.120.0.0/16 network.
However,I want this same ssid to be brodcasted to a remote site using HREAP access point but with different dhcp scope 10.102.0.0/16.
I have tried creating another interface for the remote site with a different dhcp scope(10.102.0.0) but the controller wont allow me create another wlan with same ssid that existed before to apply the new interface created for.
The 5508 is running code 7.0.116.0. I have created a group interface for 3 subnets and assigned the group to the WLAN. Clients are getting IP addresses in a round robin fashion. The issue or downside to this is if the lease has not expired before the next time the station connects to the WLAN it consumes an address on another subnet instead of grabbing the unexpired lease IP address on it's previous VLAN. It seems that the WLC determines the VLAN in the interface group before the DHCP request from the client in case the client already received a DHCP address that has not expired. This can be problematic since we have seen some iPhones requesting an address every 20 minutes thus consuming an address on every subnet in the interface group. Other than setting a lease time extremely low what can be done to address this?
View 1 Replies View RelatedI am using Windows 2011 SBS and Windows 7 clients.My server has a DHCP range of 192.x.x.150 to 192.x.x.199 and all other I.P. addresses are static. On a workstation located at I.P. 192.x.x.13 I am seeing an address conflict.When I perform an "nbtstat -a 192.x.x.13" command from the server I am given the logical computer name of a staff members personal laptop.Investigation of the laptop reveals that it is set to DHCP, and clearly the address of 192.x.x.13 is outside of my servers DHCP scope, so this I.P.should never be assigned, let alone in duplicate.I Google this topic before posting, and it was suggested that IPv6 could be having an adverse affect. I determined this because I performed a ping on the laptop and only got a MAC address back rather than an I.P. address.However after unticking IPv6, and rebooting, the laptop is still causing havoc.I can set a static I.P. address on the laptop, however this is not ideal.
View 2 Replies View RelatedI have a ASA5505 that i have running asdm 6.4 on it and have tried setting up some DHCP scopes for the interfaces.I have the security plus key.I set up 4 interfaces all with different subnets and all with different DHCP being doled out by the firewall for the time being.Anyway, 3 of the 4 work.I have tried to change interfaces wondering if there was an issue with that phy device.I tried enableing the subnet that would not work first and it didnt matter still would not issue dhcp.the other 3 work fine.Is there a limitation to the amount of scopes that will issue dhcp for an asa5505 ?
View 3 Replies View Relatedi am using wlc 4402 with a mgt ip 172.26.150.x/24 and ap manager ip 172.26.150.x/24, my all ap get the ip address from dhcp . currently in dhcp server 172.26.150.3 to 254 dhcp scope is configured. at mysite some devices are configured like ipad,iphone or galaxy tab with mac binding in dhcp server. now this pool is almost full. i have a policy configured for these devices for mac binding is done in DHCP. to increase pool what are the changes i need to do in wlc. what are the changes i need to do in dhcp server . is policy made for mac binding in dhcp server will get affected by this ?
View 2 Replies View RelatedI change DHCP scope to match corporate IP scheme Friday came back To discover only some stations picked up new leases from the scope.
View 2 Replies View RelatedMy Network is running Windows Server 2003 and with more than 150 Users. But last week, I notice that a program is changing my DHCP server IP Address scope.
View 2 Replies View RelatedI did the config below but unable to obtain the ip from the subnet scope 10.10.9.0. The switch is in the layer 3 mode.
no spanning-tree
vlan database
vlan 2
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
[code]....
Just inserted a new 5508 WLC into the network. We current have 3 4404 WLCs, and there was a need to duplicate, as much as possible, the configurations on the 4404s, and the design. The 5508 came online as expected. We moved a few access points over to it. The APs got the correct address range. The clients are expected to get addresses in the same scope range as the APs. However, the clients are receiving addresses in the management IP scope.I know there are two "not a good way to do it" in here. Why is the management address range in the DHCP scope, and why are the clients using the same scope as the APs. We are going to change that. For now, the AP and client in the same range has been going on since we rolled out wireless in 2006.The 8 ports on the 5508 are configured for LAG. There is no dedicated port for management. They tell me not to do that on a 5508.
View 8 Replies View RelatedI am trying to setup VLANs and most of configurations are working ok now except IP address assignment from DHCP. If any computer in VLAN 120 or 130 configured with manual IP address, then all works fine. It can reach internal servers and the internet without problem.If the IP address is assigned automatically then any computer in VLAN 120 or 130 are obtaining IP address (strangely!) from VLAN 100. Because switch ports that connected to the computer belongs to VLAN 120 or 130, the computer cannot reach internal servers and the internet with ip address from VLAN 100 . All SVI interfaces for VLAN 100, 120 and 130 have ip helper-address option defined pointing to the DHCP server. No DHCP snooping enabled on all switches at this point. DHCP server have three scopes for the three different VLANs.
View 2 Replies View RelatedThe company I work for owns a remote manufacturing facility that houses a stack of five 3750 switches that function as the core switching system for the plant. DHCP services are configured on the 3750 stack.
There are currently three VLANs configured, one for data and one for voice (144 and 244 respectively) and one for UCM servers (200), with corresponding subnets of 10.44.32.0 /19, 10.44.0.0 /19 and 10.44.100.0 /24.
The current DHCP scope configurations are as follows:
ip dhcp pool Plant-44_DHCP
network 10.44.32.0 255.255.224.0
default-router 10.44.33.254
[Code].....
My question is will the addition of this scope in the manner presented cause any problems with PCs or IP phones outside the targeted recepents receiving the wrong IP information from this scope?
I plan to identify the users that should be members of this VLAN 444 and change the switchport mode access configuration on the corresponding switch ports from VLAN 144 to VLAN 444. The voice VLAN 244 will remain the same.
We have a WLC 4410 management IP Address configured as 10.40.124.59.and configured VLAN1 on WLC with IP address 10.40.126.250. we are unable to ping the VLAN1 ip address from the switch. even unable to ping 10.40.126.252 (Gateway). Is there any limitation that we can not configured ip address from secondary scope...Switch vlan 1 configuration is ......interface GigabitEthernet0/0.1description Business VLANencapsulation dot1Q 1 nativeip address 100.93.50.2 255.255.0.0 secondaryip address 10.40.126.252 255.255.255.0 secondaryip address 10.40.124.61 255.255.255.192 secondaryip address100.43.94.252 255.255.255.0.
View 3 Replies View RelatedHave a WLC 5508 running 7.0.230 with internal DHCP server. Timeout is 3600 seconds. The IP addresses never seem to be released. The controller will show 70 clients but 254 addresses will be assigned.
View 2 Replies View RelatedThe two controllers are having two internal DHCP servers with the same range in LAN (enx1,enx2). but i have specified which is primary DHCP server(enx3) in WLAN interface.
Now if a new user added into network, will he get IP address from primary dhcp(WLC) or AP connected WLC.
if two users connected to 2 diff AP's which are connected to 2 WLC will get the same IP address? since having same address pool configured.
How do Mobility Groups work with internal DHCP scopes on a WLC 5508?We have a WLC 5508 with two internal DHCP scopes which redirect to captive portals for authentication. I am looking at putting in a second WLC in a mobility group setup to provide some WLC redundancy. The LWAPs will be setup so that every second AP is on the has the second WLC as its primary controller. If the primary WLC fails we want the secondary to be able to take over and issue IP's from the internal scope. How do you set this up with a Mobility group so the second WLC does not act as a rouge DHCP server while the primary WLC is still active?
View 6 Replies View RelatedWe created the management interface, an internal DHCP scope in same subnet, and Two SSID tied to the same management interface:
- when we connect to the first SSID we have and IP address
- but when we connect to the secone SSID: impossible to get an ip address - auth and association are OK
I am hoping to get your feedback around the dhcp issues I am facing with Two Centrally Switched Wireless LANs. The setup is as follows:
- I have a WLC 5508 which has been configured with 4 SSIDs, out of which 2 are using Central Authentication and Switching. - I have an LWAP connected to the WLC in HREAP mode. - WLC is configured as the DHCP server for clients connecting to the SSID 'Guest'. For the rest, I am using external dhcp server. - Only one scope for Guest Interface is setup on the WLC.
Problems:
1. As far as I know, for WLC to act as internal dhcp server, it is mandatory to have the proxy enabled, but the Clients connecting to SSID 'Internet' are unable to get an ip address from the external dhcp server, if dhcp proxy is enabled on the WLC. If i disable the proxy, it all works fine.
2. DHCP does not release the ip addresses assigned to clients even after they are logged out.
3. If a machine which was earlier connected to 'Guest' SSID connects to the 'Internet' SSID, it requests the same ip it was assigned by the WLC which it was assigned under 'Guest', but gets tagged with the V LAN configured on the management interface.
************Output from the Controller********************
(Cisco Controller) >show sysinfo
Manufacturer's Name............. Cisco Systems Inc.Product Name................ Cisco Controller Product Version................. 7.0.116.0Bootloader Version................ 1.0.1Field Recovery Image Version..................... 6.0.182.0Firmware Version..... FPGA 1.3, Env 1.6, USB console 1.27Build Type.......... DATA + WPS + LDPE
[code]...
A client wants us to use the internal DHCP server on a 5508 instead of Windows DHCP. They will have 15 APs initially and upto 25 later. The docs on the 7.2 WLC make it sound like this is discouraged: Internal DHCP Server.
The controllers contain an internal DHCP server. This server is typically used in branch offices that do not already have a DHCP server. The wireless network generally contains 10 access points or fewer, with the access points on the same IP subnet as the controller.
In this case, the APs will not be in the same subnet as the Managment Internet.Is it a mistake to use the internal DHCP with upto 25 APs (3 WLANs)?
i created the 10 V LAN in my Cisco 3750 switch.All other V LAN DHCP IP's (192.168.2.X - 192.168.10.X) will be release from the DHCP server except VLAN1 . In my 3750 switch i created DHCP pool(192.168.14.X).... and i assigned to VLAN10.... but one of the client is assigned to V LAN 2(192.168.2.X) configuration. but its getting IP from the Cisco DHCP instead of DHCP server.
View 2 Replies View RelatedI've heard mixed things about the use of DHCP release messages. I've heard that some operating systems don't bother with them at all, which makes sense because many users disconnect the network media without shutting down the workstation. Which operating systems actually send out release messages as part of their shutdown sequence?
View 5 Replies View RelatedCan add feature "release" and "renew" to wan dhcp client? Is it WOL not possible in RV220w? i tried forward broadcast magic packet from wan side, change broadcast IP and through VPN tunnel (PPTP & IPSEC)...got failed i change from draytek 2130n to rv220w, 2130n much better. except SSL VPN.
View 2 Replies View RelatedIs it possible to have more public addresses to more internal addressees? I have an internet provider which is in control of my router and he is telling me it is not possible. It's a Cisco router and I have static IP address.
View 1 Replies View RelatedI have multiple devices running on my home network. Every once in a while my wireless router starts playing up and I have to reset it.Whenever this happens, it changes the internal IP addresses of the devices. Is there a way to make the router keep the same internal ip address for each device? ie Laptop stays at 192.168.1.8I have a few forwarded ports for remote access to certain pieces of software, so each time the address changes, I have to go in and change these details, which is quite frustrating.
View 7 Replies View RelatedI recently cut over from a WRT54G to a RV120W. I am having an issue where I type [URL] (for a server running on my network) in my web browser while on the internal network and it always comes back with the router login page. Basically it is supposed to go out of the router and then come back in on the public IP address and hit that server. There was a function on the WRT54G called "Filter Internet NAT redirection" which when turned off would allow this to happen. I am not seeing a feature like this on the RV120W
[URL]
ASA 5505 Firmware 8.3(4), ADSM 6.4(2).I have a public IP address of 168.87.3.4.I need to forward ports (5060, 5080, etc.) to one internal address. (192168.1.1).I need to foward different ports (10020-10080) to a different internal address (192.168.1.2) Everything I read tells me how to do this in a 1 to 1 static NAT.
View 1 Replies View RelatedI've just installed a 2106 Controller at a remote site. The Controller is seen by the WCS at the main site so, connectivity is good and I'm able to login from the main site. I've configured the DHCP server which is at the Main site on the AP manager interface and the Manager interface and on the WLAN of the new controller but, APs are not getting addresses.
View 6 Replies View RelatedHow can i configure DHCP to use two different range of IP addresses. One range will be for example 192.168.0.* and the other range will be 192.168.1.* When the first range of ip is full the DHCP automatically assign IP addresses from the second range.
View 9 Replies View Related[URL] I have one Controller 5508 is my Central Office and I have some Ap's working in local mode in my Central Office, additional I have more Ap's in a remote Office they're are working as H-REAP and I can handles across my WLC. Now my enterprise decided bouth another WLC and wants to deploy a active-passive scenario. This new Controller should manages all the AP's when the central WLC fails...
My questions are... I need to have the same ip addressing on both sites? or they can be different. I nedd to configure some on my Ap's that are working as local mode, for allow the secondary WLC manage them when mi central WLC fails
Our 5508 Wireless Controller will drop MAC addresses clean out of the system. Addresses that are in use everyday just disappear. It is not a limitation issue because we are adding iPads everyday. And it is not a daily occurance, but maybe once or twice a week. Everything has been updated and it is more of a hassle than anything, I am just trying to understand what is happening.
View 2 Replies View RelatedI work on a college campus that has thousands of students a day accessing our wireless network. We have broadcast SSID that the students use to connect to the internet. The students usually have more than one WiFi enable device on them and their laptops and phones both take an IP address, but they are only using the laptop to authenticate while the phone is associted, but not authenticated. In the meantime, I have several thousand IPs being used by their phones/iPods etc. Is there a way to revoke the DHCP lease if the client does not authenticate within a specified time frame (i.e. 10 minutes)?
View 3 Replies View RelatedInitially there were 3 SSIDs configured but all of them were assigned a single interface and this interface was configured with the controller management IP address as DHCP server so that the WLC could assign IP addresses to wireless clients, guns and printers etc.
Issue: As part of PCI initiative, we decided to segment the traffic in multiple subnets based on type of wireless clients; so now there are 3 interfaces configured and each SSID is assigned a specific dynamic interface and each interface is configured to use the controller management IP address as DHCP server.
There are 3 scopes configured for each of the dynamic interfaces/SSIDs and DHCP proxy is enabled but wirelss clients are still being allocated IP addresses from the original DHCP scope that was associated with the dynamic interface originally assigned to all 3 SSIDs.
I verified the following:
1. Each SSID is assigned a different dynamic interface (Users, Voice and Handhelds)
2. Each dynamic interface is configured to use controllers management IP address as DHCP server
3. DHCP scopes configured with correct network information for each dynamic interface and enabled