I recently cut over from a WRT54G to a RV120W. I am having an issue where I type [URL] (for a server running on my network) in my web browser while on the internal network and it always comes back with the router login page. Basically it is supposed to go out of the router and then come back in on the public IP address and hit that server. There was a function on the WRT54G called "Filter Internet NAT redirection" which when turned off would allow this to happen. I am not seeing a feature like this on the RV120W
I want to connect two sites through a VPN tunnel, such that each machine can access all others, regardless of which site they're located.
The two sites have a VDSL connexion with dynamic public IP addresses. Unfortunately, our ISP does not offer static IP addresses with VDSL connexions.
I plan to do the following : install two RV 120W routers, one at each site, right after the VDSL modemconfigure the modems in bridge mode, such that the 120Ws get directly the WAN IP address and trafficuse DynDNS to assign domain names (site1.dyndns.org and site2.dyndns.org) to each siteassign different subnets to each site (ie 192.168.1/24 for site 1 and 192.168.2/24 for site 2)configure a VPN tunnel in gateway mode using the FQDN (site.dyndsn.org and site2.dyndns.org) of each site on both routers, with corresponding remote subnets
if possible with the RV042.Primary External IP address uses port forwards for some ports, all okay.I would like to have other external ip addresses assigned to machines on my lan.Basic host multiple web servers, on different IP addresses, using port 80. [code]
From what i am reading, it looks like the RV042 can do this, but I am not real clear what my rules should look like.
I would think my high priority rule for each external IP address would be to deny all traffic first for each machine on the lan.Then create one entry with source 202.x.x.2 port 80 -> 192.168.168.2 ?
How should I set my rules to do this, and what settings should I have on the Nic of the second machine?
I managed to set up an ipsec vpn between the RV 120W (responder) and Shrewsoft vpn client.The virtual ip and dns for the client pc are manually set. The tunnel is enabled, but I see no traffic between the local and the remote LAN.I can't ping or reach any pc behind the router.Using the command ipconfig /all on the client pc, I see that no gateway is assigned to the virtual vpn interface.So it seems that the RV 102W is unable to pass to the client the address of the default gateway for the lan, and I think this is why I can't access any resource.
Trying to get a service setup with a third party to access our system (ERP web service to access our ERP data, making data available to customers and vendors via internet). They require that I setup four external IP addresses to have access through the firewall. I haven't figured out how to do this. I'm using a Linksys WRV200 router.
I have a RV 120W router and SBS 2011 Essentials server. The remote access was working porperly, but now when I type the URL it brings up the RV login screen instead of the Remote Access sign in page. I am not certain what settings are messed up.
I have block some website in URL Blocking.But they can access the website which i have blocked through proxy server? Can i deny user access proxy server? It has many proxy server,i can not block the proxy server one by one.
Our secondary site accesses the internal intranet via a link, which is basically:
[URL] where externalip is the IP address of my router.
* This used to work fine before we migrated from ADSL (6mb up / 0.5mb down) to Fibre(70mb / 20mb) *
Internally, I access the same link, but via [URL] Internally it loads in 2 seconds, externally it is taking 68seconds(ish)..
I can't work it out, the fibre shouldave made things loads quicker but is infact very slow. I'm wondering if something network wise is going on.
The intranet is a php intranet sitting on apache, and using postgresql as the database. Other pages load fine, this specific index.php page does quite a lot of DB connections and so on, but as I say before, it worked fine before the migration.
I am aware that we can allow external admins to telnet over a custom port to the internal router. Even i was allowed to connect to a remote router via the remote firewall. The way i was accessing the router is by telnet to the remote ASA address on port 8023.I am not sure how exactly we can configure this on a ASA.
I am having some trouble accessing some backup Email (Outlook Web Access) and Citrix servers located behind an ASA 5505 firewall at a remote datacentre. Simply put, when I go to the specific URL (e.g. [URL]) I do not arrive at the splash page, I just get a message saying that the server took too long to respond in the web browser. I'm wondering whether I have missed something on the configuration or the firewall itself is not letting my requests through. The remote servers are located at a remote Disaster Recovery site and use the subnet 192.168.4.0/24. I am at head office which is connected to the DR site via a VPN using 192.168.1.0/24.
We have an ASA 5505 running version 8.4. We are having problems allowing external traffic to access computers behind the firewall. Our current config is:
I'm using a 2601X router connecting to a broadband connections. The following NAT connections is working but I need to do NAT exemptions to set up my VPN appliance on the DMZ. I see a lot of documentation on how to use a pool of public addresses to do that, but I only have the one dhcp address from my isp.
! boot system flash:c2600-adventerprisek9-mz.124-25d.bin ! ! ! interface FastEthernet0/0
I have a issue that i am at a loss as how to solve it. I have an ASA 5505 as my firewall. I have users from other companies who visit from time to time and are unable to use their outlook email to send messages. They can however receive messages without a problem. I also have a situation where users who use windows live to access gmail are unable to send messages.
I have narrowed it down to the fact that these uses are using ssl/tls to send the mails. I did some research and found out about the inspect esmtp setting in the ASA. I have disabled it and i still have to problem. I have also removed all outbound deny statements and still no luck.
Of note is that i can send emails without attachments. They take a long time to go out ( from minutes to hours) but eventually they do. Emails with attachments of even 10k do not go at all.
I was running image 8.2.3 and i downgraded to 8.0.5...still did not work...i upgraded to 8.4.3...still did not work. I am now back at 8.2.3.
My Firewall config is attached. I am at my wits end as to what else to try. The company has not renewed support for the device so i am on my own here!
We recently purchased an SRP527W router because of its capability to configure site-site VPN tunnels. The configuration of IKE and IPSEC is working and the tunnel comes up but the problem is that the router is passing our internal IP addresses through the tunnel. The remote end we are connecting to requires us to hide all traffic behind one IP address which would ideally be our external static IP address from our ISP.
Is it possible to have more public addresses to more internal addressees? I have an internet provider which is in control of my router and he is telling me it is not possible. It's a Cisco router and I have static IP address.
I have multiple devices running on my home network. Every once in a while my wireless router starts playing up and I have to reset it.Whenever this happens, it changes the internal IP addresses of the devices. Is there a way to make the router keep the same internal ip address for each device? ie Laptop stays at 192.168.1.8I have a few forwarded ports for remote access to certain pieces of software, so each time the address changes, I have to go in and change these details, which is quite frustrating.
In setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
I have the RV 120W router, and can not seem to get SNMP Set to work. I though I would just check here, and make sure it is supported, and if it is, are there any special config settings I need to use?
I am interested in the QuickVPN solution for a Mac.I am getting mixed messages in my searches.If not, what is the secure, reliable way to use an RV-120W with a Mac?
I've installed RV042 for a client of mine. For next two months everything worked without any problems. The issue I've been experiencing lately is when I assign a static IP address to the PC it won't have internet access. Once I allow it to have a dynamically assigned IP then it works fine. The IP I assign isn't part of the DHCP range.
For the life of me I can’t get my quick VPN client to connect to my Cisco 120w. I have IPSec gateway to gateway setup and working just fine. I made my quick vpn client under vpn tab. I enabled remote management. Every time I try to connect I get the failed to establish connection. Using the same quick VPN software I can connect to a rv082 with no trouble.
I recently replaced a client's router with a Cisco RV 120W. The client employs a web-based application on an internal server that manages their business. Workers in the field use a handheld device power by WIndows Mobile to access a mobile version of the the web-based app. Data contained on the mobile app syncronizes with the server when workers choose a sync menu. Some workers perform this sync in the field, others wait till they return to the office and use the wireless provided by the router. Prior to changing the router, the synching worked fine either inside or outside the company network. The mobile app accesses the internal server via the router's public IP address. The router forwards the http requests to the internal server. But now the synching does not work internally. I assume it's because the Cisco RV 120 W does not support NAT Loopback, or I simply haven't figured out how to enable it. Does anyone know how to enable NAT Loopback on the RV 120 W so I can access the web-based app by through the router's external IP while on the private side of the LAN??
I just installed a new RV 120W to replace my dlink router.The problem is i cant display the configuration site (192.168.1.1). My internet is working fine and when i go to 192.168.1.1 i can logon (with the password i set using the installation disk) but then i see the top of the config site (blue) but where the config panel should be i see `site cannot be displayed`.
i am using the router,rv 120w can i redirect website to a special IP? for example,the website www.cisco.com, can i redirect it to the IP :8.8.8.8 in router?
I am not a tech guy but have to take care of some basic IT stuff. I had Ether fast cable/DSL router and it got changed with RV 120W router. there were comment that internet is now working slowly - what could be the reason for this?
I copied most of settings. First big technical problem was with phone. It stopped working - call could get through but when answered there was no sound. We use linksys modem for VoIP. I called operator and was told to disable sip alg. I did that and service improved a little. When answering a call sound could get through but would stop for few moments and then continue. Operator told me to forward port 16384 to 16482 to VoIP modem IP. But I can only set forwarding for one port at the time in "Port forwarding" settings. Is there a way to forward to port range?
I have a 1760-v router set up at my home lab and I am unable to access IP addresses outside my local network. I have my Cisco router's fast Ethernet port connected to a small net gear router which then connects to my cable modem. The Cisco router is able to ping local address fine, but when I try to ping an outside address or domain name it times out. However, when I am at the CLI and type something like Ping { URL}, it resolves Google's IP address but it will not ping it. I have IP DEFAULT-GATEWAY and IP NAME-SERVER both pointing to my net gear router and pointing to my ISP's DNS server.
I'm am using Google Analytics for my webpage, and I want to exclude(filter) the IP range of my router's external IP addresses from the Analytics data. How do I determine the IP range of my router's public IP?
I have a 2600 I am trying to setup for educational use.
My Cable ISP has issued me 5 routable IP's through their SMC modem 86.28.12.226-229. The SMC modem is .225. Currently the internal network can get out through .229 as expected but nothing outside (tcp 80 to web server) can get through. When I assigned the ip's to e0/1 as secondarr I could get it to route from the inside network (so hitting .226 80 went to the correct place) but it still didn't work from the outside - plus I read that wasn't a great way to do it anyway.
! interface FastEthernet0/0 description LAN Interface
I have a checkpoint Safe@Office 500 firewall router, connected to adsl via another adsl device in bridged mode.We needed to assign an external IP to a device behind the firewall.We contacted the ISP, and now they have assigned an additional IP to our adsl account.I have read from the documentation that:"NAT can be defined automatically via the network object (Node, Network or Address Range). When you define NAT via the network object, rules are automatically added to the Address Translation Rule Base"....so I add the object, with the external IP given to us by our ISP, and the wizard simply complains that the IP address is invalid.My thoughts are that the router does not know about the additional IP provided by our ISP. If so, how do I tell the router that there are other IP addresses available to use? I have rebooted the router, and no luck.
