I have a RV 120W router and SBS 2011 Essentials server. The remote access was working porperly, but now when I type the URL it brings up the RV login screen instead of the Remote Access sign in page. I am not certain what settings are messed up.
View 3 RepliesI have a RV120W; configured to perform port forwarding. I have Configured a Port Forwarding and Access Rule
* Sample Firewall: Access Rules:
Action | Service | Status | Connection Type | Source IP | Destination IP
[Code]....
Everything works, but in my destination server, i see as remote address the IP for the RV120W. I want it to forward also the originating IP address of the client (the remote address)
Is it possible to configure this?
I have also configured DMZ for my server, but see same behaviour
Firmware: 1.0.3.10
I managed to set up an ipsec vpn between the RV 120W (responder) and Shrewsoft vpn client.The virtual ip and dns for the client pc are manually set. The tunnel is enabled, but I see no traffic between the local and the remote LAN.I can't ping or reach any pc behind the router.Using the command ipconfig /all on the client pc, I see that no gateway is assigned to the virtual vpn interface.So it seems that the RV 102W is unable to pass to the client the address of the default gateway for the lan, and I think this is why I can't access any resource.
View 4 Replies View RelatedI have block some website in URL Blocking.But they can access the website which i have blocked through proxy server? Can i deny user access proxy server? It has many proxy server,i can not block the proxy server one by one.
View 1 Replies View RelatedI recently cut over from a WRT54G to a RV120W. I am having an issue where I type [URL] (for a server running on my network) in my web browser while on the internal network and it always comes back with the router login page. Basically it is supposed to go out of the router and then come back in on the public IP address and hit that server. There was a function on the WRT54G called "Filter Internet NAT redirection" which when turned off would allow this to happen. I am not seeing a feature like this on the RV120W
[URL]
I recently Installed AVG 2011 and AVG PC tune-up 2011. When i just start my computer the internet is working fine, but after a open my game Flyff, The internet is still connected but cannot use it.
View 2 Replies View RelatedI have an RV180W router and I am trying to use the Windows 2011 SBS. It seems like I setup everything properly in order to use the remote access, but when I try to log on from home, I don't have any luck. According to Window's instructions, here's what I have setup on the router side:, I turned on UPnP. (they say to either do port forwarding, or UPnP, but I found on the Windows SBS that I had to do both in order for it to say it was working).
View 2 Replies View RelatedI'm considering upgrading my home server to 2012 Essentials from WHS 2011. WHS 2011 has always been strangely finicky and I have a new Win8 laptop, so i would like to take advantage of the new options in Essentials.that said, I was looking to access my data on the WHS 2011 system to back IT up, and all I see are a bunch of 4,194,304kb .dat files. I've been lucky in that I have never had to recover data from the server, so this has been an interesting issue. how does one access the backed up files on a WHS2011 computer, short of doing some kind of restore?
View 2 Replies View RelatedI have the RV 120W router, and can not seem to get SNMP Set to work. I though I would just check here, and make sure it is supported, and if it is, are there any special config settings I need to use?
View 2 Replies View RelatedI am interested in the QuickVPN solution for a Mac.I am getting mixed messages in my searches.If not, what is the secure, reliable way to use an RV-120W with a Mac?
View 1 Replies View RelatedFor the life of me I can’t get my quick VPN client to connect to my Cisco 120w. I have IPSec gateway to gateway setup and working just fine. I made my quick vpn client under vpn tab. I enabled remote management. Every time I try to connect I get the failed to establish connection. Using the same quick VPN software I can connect to a rv082 with no trouble.
View 2 Replies View RelatedI recently replaced a client's router with a Cisco RV 120W. The client employs a web-based application on an internal server that manages their business. Workers in the field use a handheld device power by WIndows Mobile to access a mobile version of the the web-based app. Data contained on the mobile app syncronizes with the server when workers choose a sync menu. Some workers perform this sync in the field, others wait till they return to the office and use the wireless provided by the router. Prior to changing the router, the synching worked fine either inside or outside the company network. The mobile app accesses the internal server via the router's public IP address. The router forwards the http requests to the internal server. But now the synching does not work internally. I assume it's because the Cisco RV 120 W does not support NAT Loopback, or I simply haven't figured out how to enable it. Does anyone know how to enable NAT Loopback on the RV 120 W so I can access the web-based app by through the router's external IP while on the private side of the LAN??
View 2 Replies View RelatedI just can not find the way to check the mac address and computer name of the client which connected to my rv 120w?
View 1 Replies View RelatedHow can i check the website history in router?I want to know the website which the user explored through the router.
View 1 Replies View RelatedI just installed a new RV 120W to replace my dlink router.The problem is i cant display the configuration site (192.168.1.1). My internet is working fine and when i go to 192.168.1.1 i can logon (with the password i set using the installation disk) but then i see the top of the config site (blue) but where the config panel should be i see `site cannot be displayed`.
View 4 Replies View Relatedi am using the router,rv 120w can i redirect website to a special IP? for example,the website www.cisco.com, can i redirect it to the IP :8.8.8.8 in router?
View 1 Replies View RelatedI am not a tech guy but have to take care of some basic IT stuff. I had Ether fast cable/DSL router and it got changed with RV 120W router. there were comment that internet is now working slowly - what could be the reason for this?
I copied most of settings. First big technical problem was with phone. It stopped working - call could get through but when answered there was no sound. We use linksys modem for VoIP. I called operator and was told to disable sip alg. I did that and service improved a little. When answering a call sound could get through but would stop for few moments and then continue. Operator told me to forward port 16384 to 16482 to VoIP modem IP. But I can only set forwarding for one port at the time in "Port forwarding" settings. Is there a way to forward to port range?
I have recently changed a couple of our companys office routers over from a netgear vpn router to this, all has gone well with the cisco router providing much better speed and reliablilty... But....
I have one little problem, at one of our offices they have a brother printer that has a scanner built in, since this change over the scanner does not seem to want to work,
as far as i can guess the router is blocking communication to the scanner, printing is working fine. is there anything that I need to enable or add to the settings on the cisco to get this working? I believe that the printer is using some kind of multicast to connect to the PC's
We have just acquired a Cisco RV120W Firewall Router and we are experiencing issues with this router. I've read some threads related to port forward issue with RV120W before writing this new topic.
We have 2 locations (site A and site B) connected with a Site to Site VPN (PPTP) running under Windows Server 2008 R2 with TMG 2010. This Site to Site VPN worked very well until we replaced our old router with the RV120W at site B. Since this moment, our engineers are not able to make the site to site VPN work again. The TMG box are located just behind the router.
We have followed some threads about Port Forwarding but it did not solve our issue (others port forwarding rules for RDP for example work). Our RV120W is running the last stable firmware (1.0.2.6) provided by Cisco.
I recently installed a new RV120W router at one of my customer's office. I have 2 users connecting using the Quick VPN software.The first one is running on a Windows XP Pro SP3. Everything works great on this PC.The second PC is running on a Windows Vista - The QUICKVPN client stays at Veryfing Network and Eventually I get an error " The remote gateway is not responding. Do you want to wait?I have disabled Firewall on both PCS for troubleshooting purposes.
View 1 Replies View RelatedI'm running FW 1.2.4 and how to setup Remote Web Access over my IPSEC vpn tunnel. I would like to be able to remotely access these routers and make configuration changes from my main office but I cannot seem to figure out how to get it to work. If I try to access the internal router IP from across the VPN, I cannot. My VPN tunnel is up and operational and I can ping various devices across the tunnel but I cannot access the web management of the router.
View 4 Replies View RelatedI have a customer that has a Cisco 2900 Series ISR on his Headquarters, and has some branches with RV082s.We have VPN Client configured on the 2900 ISR Router and we can connect remotely using the VPN Client to the Headquarters (192.168.1.0) however we can't reach the branches subnets (192.168.2.0, 192.168.3.0, etc.)... we found out that in the RV082 you need to specify the secure traffic as a destination, but in only supports one network (192.168.1.0 or Headquarters in this case), we can't specify the VPN Client pool defined on the ISR so it can reach the incoming VPN Clients.Is there any way to accomplish this? We need to access the branches subnets when connecting using VPN to the 2900 ISR.
View 1 Replies View RelatedRVL200 firmware 1.1.12.1 iPad2 cannot access any device on the remote LAN despite the closed padlock icon.Is there another App needed ? Or how to debug the SSL VPN ?
View 2 Replies View RelatedI'm using SRP527W router at the moment and there are 10 PCs in the office.First of all, I'm not expert on network administration at all.Anyway, I set up remote access for particular PC and it works good.I made it like this.Add "Port Forwarding Entry" in Network Setup > NAT > Port Forwarding menu.
- Type: Single Port Forwarding
- External Port: 3389
- Internal Port: 3389
- Protocol: TCP and UDP
- IP Address: 192.168.0.20
I need to set up another remote access for another PC (IP: 192.168.0.25).I'm not quite sure I can use 3388 port for remote access.However, I added another "Port Forwarding Entry"
- Type: Single Port Forwarding
- External Port: 3388
- Internal Port: 3388
- Protocol: TCP and UDP
- IP Address: 192.168.0.25
However, it doesn't work.when I tested internal network(use private IP -192.168.0.25:3389), it works fine.But when I tried through the Internet (use public IP 202.171.xxx.xxx:3388), it returns "Remote Desktop can't connect to ...." message.How can I open 3388 port in router administration colsole(Services Ready Platform Configuration Utility)?
is it possible for me to use the Remote Support Feature? If I start a terminal connection I will answered for user/pass If I type in the routers web frontend admin credentials I get a access denied. Which user/pass do I have to use? Or do I have to configure something else in the frontend?
View 2 Replies View Relatedhow can I remote in to my router and I need to get past my router to my pc desktop
View 2 Replies View RelatedI am trying to connect to my office PCs via VPN and/or RDP. The office uses Qwest DSL and has a dynamic IP address. I use DynDNS.org to keep the DNS updated with the WAN address of the router. However, any attempt to access the network fails. I have tried remote management access (I enabled it on the router) but that fails. I forwarded RDP ports on the router to one of the PCs but can't connect to it. I also set up a VPN server but cannot connect to it either. Something tells me that all requests to myoffice.homeip.net are not getting to my modem/router. I have even tried the IP associated with the name (Yes, I did check that it is correct!) but nothing works there either.
View 1 Replies View RelatedI have a RV082 and several of my remote laptops cannot access my server using its domain name. It can be accessed using its internal ip address. The issue is that you can log onto the server using remote access and the ip however you cannot use any shortcuts using the domain name. You can see the server with the domin name however no access path is available. This is only on a few remote user laptops. Others work perfectly.
View 1 Replies View RelatedI want to connect two sites through a VPN tunnel, such that each machine can access all others, regardless of which site they're located.
The two sites have a VDSL connexion with dynamic public IP addresses. Unfortunately, our ISP does not offer static IP addresses with VDSL connexions.
I plan to do the following : install two RV 120W routers, one at each site, right after the VDSL modemconfigure the modems in bridge mode, such that the 120Ws get directly the WAN IP address and trafficuse DynDNS to assign domain names (site1.dyndns.org and site2.dyndns.org) to each siteassign different subnets to each site (ie 192.168.1/24 for site 1 and 192.168.2/24 for site 2)configure a VPN tunnel in gateway mode using the FQDN (site.dyndsn.org and site2.dyndns.org) of each site on both routers, with corresponding remote subnets
I have setup a site-to-site VPN tunnel between 2 sites using CISCO rv120w.Everything works fine; any PC on one site can access all systems on the other site and vice-versa.The issue I have is when I start a VPN connection another site on Internet using IPSecuritas.I can initiate a VPN to site 1 and site 2; but when connected, I can only access servers that are located into the same site I'm connected to; I cannot ping the remote site.The Range of IP addresses on the internet during my tests is 192.168.11.0 (I 'm using a Mac)
-Systems with IP 192.168.1.1 and 192.168.10.1 are bridges
-Systems with IP 192.168.1.2 and 192.168.10.2 are CISCO rv120w
I have a Cisco 678 connected to my ISP (Qwest) using DHCP. This is connected to a Linksys WRT54g router. I also have a home server running for remote access to some files and media streaming. I just installed security cameras that I wish to monitor remotely via the internet.I can access my home files over the internet with no issue. However I am unable to access my cameras using the internet. Looking at my router incoming log, I see my request arriving, but I never get to the DVR attached to the camereas for remote viewing.I enabled bridging on the Cisco 678 but this did not solve the issue.
View 1 Replies View RelatedMy company is using an RV016 router as a gateway to our internal network. My end goal is to allow remote users to access network shares via Samba.I've been trying to create a VPN using the router with absolutely no luck. I've tried QuickVPN. I've tried creating a client-to-site group vpn. I've tried creating a client-to-site tunnel vpn. I've tried pptp. Nothing will allow me to establish a VPN connection. Sometimes there is information logged in the router but most of the time there is not.
View 1 Replies View RelatedI am trying to configure RV082 router with Mac Native VPN Client for my remote access. However, no matter what I did, I am not able to make it works. Can any one can give me an example of how to conguration my RV082 router and Mac Book Pro(Mountain Lion)?
View 2 Replies View Related