Trying to get a service setup with a third party to access our system (ERP web service to access our ERP data, making data available to customers and vendors via internet). They require that I setup four external IP addresses to have access through the firewall. I haven't figured out how to do this. I'm using a Linksys WRV200 router.
View 1 Repliesif possible with the RV042.Primary External IP address uses port forwards for some ports, all okay.I would like to have other external ip addresses assigned to machines on my lan.Basic host multiple web servers, on different IP addresses, using port 80. [code]
From what i am reading, it looks like the RV042 can do this, but I am not real clear what my rules should look like.
I would think my high priority rule for each external IP address would be to deny all traffic first for each machine on the lan.Then create one entry with source 202.x.x.2 port 80 -> 192.168.168.2 ?
How should I set my rules to do this, and what settings should I have on the Nic of the second machine?
I recently cut over from a WRT54G to a RV120W. I am having an issue where I type [URL] (for a server running on my network) in my web browser while on the internal network and it always comes back with the router login page. Basically it is supposed to go out of the router and then come back in on the public IP address and hit that server. There was a function on the WRT54G called "Filter Internet NAT redirection" which when turned off would allow this to happen. I am not seeing a feature like this on the RV120W
[URL]
How do i tell my firewall to start listen also on another outside ipadress assigned by my ISP? I have it used on other firewall right now. So my steps would be shutting down ip address assignment off old firewall interface. Assign that ip address to ASA5510 outside interface and configure NAT.
View 13 Replies View RelatedI am a total Cisco novice who has just had a ASA5505 installed to replace a linux freeware firewall (smoothwall).I'm told that the 5505 can't port forward traffic (e.g. ssh) from two external IP addresses to two internal destination machines via the same port # (22 in this example).
View 9 Replies View RelatedI have purchased a subnet of 8 private IP addresses from my ISP. 109.x.x.128/29.The ISP has placed a juniper router within our data centre which is routing purely from 109.x.x.206/30 to 109.x.x.128/29 with the ip of fa0/1 set to .129.
I have linked a cisco 5505 to fa0/1 of the juniper from fa0/0 and configured its IP to .130. I have configured NAT to translate our client pool 192.168.16.x /24 address' to the internet.
Is it possible for the 5505 to route / map my remaing private IP addresses through its external port? I have tried creating a seperate VLAN for a DMZ for our servers to sit within but am returned with a subnetting error as VLAN for my external port is all ready configured within the same subnet.
I'm trying to setup a VPN Tunnel between RV082 and WRV200.The RV082 has an static IP, the WRV200 has a dynamic IP. I have to Dyndns.org in the WRV200.I have setup the RV082 tunel auth like: Dynamic IP + email.In the WRV200 I setup the hostname with the username, and the domain with the domain part of domain entered in the RV082.In the RV082 VPN Log I got: Initial Aggressive Mode message from 11.22.33.44 but no (wildcard) connection has been configured.It seems to be working the IPSEC setup but the RV082 does not accept the connection because of a missmatch in the Remote Security Gateway Type parameter in the RV082.
View 1 Replies View RelatedI Changed my old firewall by an ASA5510, since that change my internet connexion is slower.Some websites takes longer to display.I would like to know if there are some specific configuration about TCP connection or DNS to setup?
I just configured the ISP DNS :
Dns server-group DefaultDNSname-server 194.2.0.20 name-server 194.2.0.50
I have Astaro UTM running on an old computer as my only firewall right now. The Astaro also serves as my DHCP server. My Wifi is provided by a Linksys E3000 running DD-WRT software. NAT/SPI are disabled on the E3000, and it forwards DHCP requests to the Astaro. All my network clients connect via wifi/ethernet to the E3000.
All clients --> E3000 (no firewall) --> Astaro --> www
I am considering setting up my own personal cloud server using a Synology NAS that I can access remotely. I would also like to remotely access my Surveillance DVR. I would like to access them via VPN or portforwarding. I do not want to use DMZ.
I would like to utilize the SPI firewall on the E3000 to provide an extra layer of defense. I would like the NAS and the DVR to be on an external LAN between the Astaro and the E3000...and all other clients being on an internal LAN behind the E3000. I have the necessary switches/cables to make this work.
My question is...How do I configure the E3000? Can I have both the internal and external LANs on the same subnet? Do I have to use the NAT on the E3000? I'd rather not...since that will render the Astaro's reporting functions rather worthless.
I would like the Astaro to remain the only DHCP server. I would like all internal LAN clients to be able to reach out to the external LAN/WAN...but the external LAN should not be able to reach into the Internal.
I have 3 WRV200 that I want to install in 3 cities.I want each router to have its own Internet connection from the local ISP.I then want each router to connect to the other 2 routers and create a 3 node WAN using VPN connections.
View 1 Replies View Relatedis it possible to make a VPN Connection with my Ipad and a WRV200 Vpn Router ?? The WRV200 is in my Company and i can start a VPN Connection with my Laptop. So this works. But is it also possible with my Ipad, so that i can get access to my NAS (Which is in my Company also)??
View 1 Replies View RelatedWRV200 does not transmit packets in Router mode. This issue has been describes already here:
[url]....
So is there a solution to forcing this router function properly according to manufacturer's declaration (router mode)?
I use a router RV082 with load balancing. My problem is when I try to access a specific site, I get the error message that my IP address changes and I can not use 2 ip address. I want to specify an ip range to always use the same WAN port.
View 2 Replies View RelatedIn setup for old RV042 (V1), when updating / adding Mac addresses, the table is always sorted by IP addresses. But in the new oneRV042 (V3) I have, even with latest firmware 4.2.1.02 the list is random, thereby increasing the chance of user entering DUPLICATE IP addr with diff Mac addr. That will result in conflict.If the firmware sorts the DHCP entries by ip addresses, user would be able to catch duplicate ip errors even if the system does not flag the errors. All Cisco smart engineers can you all get the dhcp entries SORT by ip addresses.
View 2 Replies View RelatedI have a cisco router 881 with advipservices running ios Version 15.2(4)M1 this router is a device that the user will connect company equipement with antivirus and such.is there a way I can force the ports like fe0 fe1 2 3 to accept only devices with specific mac addresses?if not, is there a way for me to apply an acl to vlanX to block everything that's not from these specific addresses?
View 4 Replies View RelatedIs it possible to enable an absolute value rate limit using QOS on a HP ProCurve 5406 switch for a particular IP range on a specific port? Is there a way to configure our HP 5406 with an absolute rate limit on "WAN" port for that server's IP range? I would like to limit it to only being capable of sending 1Mbps worth of traffic over the head end at once.Everything in the documentation points towards priority queues, which as far as I can tell, isn't really what I want.Baring accomplishing this goal using rate limiting is there a better way to prevent our services from accidentally saturating this connection?i thimkong about somthing like that:
class ipv4 rate-limit-port-A1
match ip 10.136.0.0/16 any
exit
policy qos port-a1-ratelimit
class servers-to-be-slowed action rate-limit kbps 1000
exit
interface A1 service-policy port-a1-ratelimit inI'm not sure about this.
I inherited a Cisco ASA 5505 and am trying to piggy back the device off of an established Network. Here is the basic layout:
192.168.10.1 (Core Router - Handles DHCP/DNS)
192.168.10.9 (ASA 5505 - Piggy backing off of Network)
192.168.40.x (ASA 5505 - VLAN)
I'm able to get onto the Internet without any problems. Devices from the 192.168.10x Network can not ping the inside VLAN1 (192.168.40.x). However, I would like traffic going from the inside VLAN to the Outside VLAN to be blocked, except for 192.168.10.1 and 192.168.10.9. I've tried using ACL's but end up killing my Internet connection. 192.168.10.1 is the default route and is how I get out to the Internet. Is this possible? Essentially, I'm trying to set up a small Network that guests can connect to. The idea is that they can get to the Internet, but that is it. They can't get to internal resources on the 192.168.10.x Network
Here is the config:
ASA Version 8.2(1)
!
hostname ciscoasa
enable password EeCsulrpu.9LalEE encrypted
[Code].....
I have a Cisco 800 series ?I need to allow access to our local server from a specific range of external ip addresses.I can open port for all external ip using this command:
ip nat inside source static tcp <localserverip> <port> interface <interface> <port
But this is not secure as is..Do I then restrict and permit access using access-list? Or is there another way altogether?
I have a 1760-v router set up at my home lab and I am unable to access IP addresses outside my local network. I have my Cisco router's fast Ethernet port connected to a small net gear router which then connects to my cable modem. The Cisco router is able to ping local address fine, but when I try to ping an outside address or domain name it times out. However, when I am at the CLI and type something like Ping { URL}, it resolves Google's IP address but it will not ping it. I have IP DEFAULT-GATEWAY and IP NAME-SERVER both pointing to my net gear router and pointing to my ISP's DNS server.
View 3 Replies View RelatedI'm am using Google Analytics for my webpage, and I want to exclude(filter) the IP range of my router's external IP addresses from the Analytics data. How do I determine the IP range of my router's public IP?
View 4 Replies View RelatedI want to redirect internal web traffic (browsing) to an external web server for Web, Virus and Spyware filtering. Those externals proxies are running in 8080 port. I have one ASA firewall and a Cisco 2600 router. I was thinking in doing PBR in the router but in the next hop I can only set one IP, not an IP and a port. So how can I redirect web traffic to an external proxy listening in 8080 port?
View 11 Replies View RelatedI have a WAG160Nv2 and I want to block specific external ip addresses from trying to get at our server that uses the WAG160Nv2 as an internet gateway. It's not immediately obvious if this can be done from looking through the config pages.
View 4 Replies View RelatedI know the CSS is too old but I have one in production environment and I was asked if it is possible to CSS to make NAT from inside addresses and translate them into one external IP address to diferent kind of communications, for example: 172.16.4.9 and 172.16.4.10 (inside addresses) should start connection to external IP addresses destinations 50.50.50.50 / 60.60.60.60 70.70.70.70 / 80.80.80.80 and so on, the default gateway to those Servers is the CSS and I would like to know if it is possible that all connection to external world to be translate into one IP address 172.16.4.100.
My CSS is 11503
Version: sg0810106
I'm trying to setup a Application specific proxy. I have tried everything that I could find via Google search and nothing seems to work. All the proxy servers I have found seem to be centered around web browsers such as IE, and firefox.
View 2 Replies View RelatedI have a RVS4000 and I am going to configure vlan in the near future. Among all other configurations sent by the internet provider company is this one :
Firewall NAT :
from x.x.2.0/24 to 0.0.0.0/24 should be NAT
from x.x.2.0/24 to x.x.0.0/21 should not be NAT
From all the other configurations, this one is not clear to me. Can this configuration be done on a RVS4000 and where can it be done.
Working on setting up a Cisco 10008 with PPPOE and it seems like we kind of have it working but only one user can get on.
Here is part of the config:
Cisco-10008#show run
Building configuration...
Current configuration : 4134 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
Also is there a way to show a specific user once they are connected with PPPOE? I'm currently using "show aaa sessions", but was thinking it would be "show pppoe something"
I have a Netgear ProSafe VPN Firewall FVX538. But I also have 10 Public IP Addresses that I will like to setup for three web services. So how do I set this up. With multiple routers. Or can my Netgear FVX538 take multiple Public IP Addresses to the same ports. If not how can setup multiple routers. one being the main one.
View 1 Replies View RelatedI am trying to setup my 3550 layer 3 switch to do hand out dhcp addresses for different vlans. It is connected to my router address 192.168.1.1. I setup a new vlan 3 and the dhcp pool.. The client gets a 192.168.3.2 address but am not able to ping the router and other clients and get out to the internet.
Here is the config that I have. I deleted the other ports because I am not using them. The vlan 3 client is on port fast Ethernet 0/17 and the router is connected to the fastethernet 0/1.
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
[code]....
I was asked to enable netflow in an ASA Firewall for Orion/Solarwinds server monitoration. Firewall is a 5550, with 4G RAM, and no extra modules but SSM-4GE. This firewall has 5 DMZ segments and ans specific segment for internet traffic.There are segments as unique subinterfaces in physical interfaces. Other segments as individual subinterfaces in the same physical interface (but individual VLANs)Usually firewall CPU flows between 30% to 40%. Rarely to 50%.
1 - How dangerous or risky could be implement netflow in this firewall?...This firewall is very critical for the customer. My concern is regrading CPU, traffic generated, memory, etc
2 - In a month, firewall will be migrated from 8.2 software version to 8.4 software version. Is there any incompatibility in some commands?...Would be recommended to perform netflow configuration after software upgrade?
3 - How could it be implemented for Orion monitoring, regarding each individual sub-interface (and so, each VLAN assigned)?I there any recommendation regarding configuration, best practices?
I'm running a windows lan that connects 3 computers and a shared storage external hard drive. The whole network, including the external hard drive is connected by ethernet back to my adsl modem/router. I want to convert the external hard drive into an ftp server to enable secure file sharing on the internet by allowing remote access (for the purpose of downloading files) to anyone that I offer a username and password to.The external hard drive is a Western Digital World Edition (blue light)I believe it's a 2008 model.The adsl modem/router is a Billion Bipac 7300(G) RA.Is this doable?
View 3 Replies View RelatedI got a different tower to use ,and added my wireless card and external antenna to it , but need setting up the new PC tower to use the wireless card and antenna. How to set up the available connections so that I can use this in my garage too.
View 1 Replies View RelatedHow do I setup to use an external USB HD (as NSD) connected to Vizio xwr100 router. Vizio thinks it is a media device and makes no connection which can be found with Win Explorer
View 1 Replies View RelatedI have a 2800 with one Gigabit interface connection to our Lan and the other interface connected to the internet with a public IP address. Now I'd like to setup the router to resolve both internal and external DNS requests. Thus requests like www.google.co.za and LocalLanPcName should be resolved to their public and private IP's respectively. [code] When I ping any name the only DNS server that is ever queried is 192.168.1.200 (it does resolve internal name correctly though).
None of the other servers are attempted to resolve the name. It does not matter if I specify a FQDN or not.
How do I setup the router so that my internal resolution is handled by 192.168.1.200 and .201, while external resolution is handled by 41.160.36 and .37. Or alternatively, how do I configure it to at least try all 4 specified name-servers for resolution, and not fail after trying the first one unsuccessfully.