Cisco Application :: CSS11503 / Make NAT From Inside Addresses And Translate Into One External IP Address?
Dec 8, 2011
I know the CSS is too old but I have one in production environment and I was asked if it is possible to CSS to make NAT from inside addresses and translate them into one external IP address to diferent kind of communications, for example: 172.16.4.9 and 172.16.4.10 (inside addresses) should start connection to external IP addresses destinations 50.50.50.50 / 60.60.60.60 70.70.70.70 / 80.80.80.80 and so on, the default gateway to those Servers is the CSS and I would like to know if it is possible that all connection to external world to be translate into one IP address 172.16.4.100.
I guess I'll start with the easy stuff, Cisco ASA 5520 ver 8.2, ASDM ver 6.2, IPSec L2L tunnel with overlapping private IPs.
I have about a dozen L2L connections on our 5520 but never had to do one with overlapping IPs. I have two that I have to build and one definitely overlaps our inside locals, and the other is requesting that we NAT our inside locals to a 10.x.x.x.
I've searched the board and found several good posts including document 112049, but I just don't seem to be able to get my head around how to translate one inside address to another. It would seem like is would be as easy as doing an (inside,inside) static NAT, but most everything has the solution as a policy NAT or doing an (inside, outside) but in the less secure address space place the name of an ACL. I have ordered that brick of a book on ASAs from Cisco Press, but need to get something going and I'm not having much luck getting this thing up and running.
Perhaps my basic understanding of NAT rules is wrong. I thought that when using NAT the command speaks to the interfaces and the direction of travel, (inside,outside). I also thought that the IP adresses used must be valid on the interface refferenced, so any refference to "inside" would have to be an address on the "inside interface of the FW and likewise for the "outside" interface. Finally, to be sure I'm not calling a duck a goose my understanding is that the following are correct; "inside local" = my private, "inside global= my peer, "outside local"= their private, "outside global"= their peer.
So if I'm translating say a 192.x.x.x on my inside local and wanted to present them a 10.x.x.x, wouldn't I need an (inside,outside)? And even though I'm translating my private IP into a different private IP, the translated IP must be on the "outside" interface because that is the interface that I want to present the new private IP on?
So for the scenario I suggested at the top where I need to translate my private 192.x.x.x into a 10.x.x.x and present that 10.x.x.x to the other side, I need something like NAT Static (inside,outside) 10.x.x.x 192.x.x.x?
I'm trying to translate my inside network of 192.168.20.0 to my outside ISP address on ASA 5505. The ping from all hosts to 4.2.2.2 works, but it still only let's one address out to translate.My configuration is:
global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0
I'm trying to translate my inside network of 192.168.20.0 to my outside ISP address on ASA 5505. The ping from all hosts to 4.2.2.2 works, but it still only let's one address out to translate.My configuration is:
global (outside) 1 interface nat (inside) 1 0.0.0.0 0.0.0.0
Obj-192.168.1.20-1 and Obj-192.168.1.20-2 contain the same host address.
The idea being that traffic destined for Obj-External-1 on port 443 will be forwarded to Obj-192.168.1.20-1 on port 443. Traffic for Obj-External-2 on port 443 will be forwarded to Obj-192.168.20-2 on port 2000.
Traffic for the first object, Obj-192.168.1.20-1, works but traffic for the second does not.
I am desperate to make some kind of translation which convert an outside IP Address of our web server to its inside ip address so that requests can be routed internally to the server.
This is what we have: A wireless network with an SSID to serve visitors. We also have an in-house web server which can be accessed internally and externally. We have a ASA 5520 that protects the internal network, including the Web server, and also routes all traffic from the all visitors connected to the public SSID to the outside. The DHCP server for the wireless network for visitors is configured to give the 8.8.8.8 as dns server. The problem with that is that the www.ourwebserver.com is resolved by Google's dns server to the public IP Address of our web server! The traffic then is sent to the outside interface of the ASA 5520. The visitor who wants to access our web server cannot connect!
How can I configure the ASA to route that traffic to our web server with the public ip address to the inside ip address of the web server?
How can you check if balance ACA is enabled in CSS11503? How can you see also if the content switch(CSS11503) is load balancing using balance ACA? "show load" command does not show it.
xxxxxx# show load Global load information: Reporting:Enabled Calculation method:Relative Step Size:Dynamic Configured:10 Actual:1280 Threshold:254 Ageout-Timer:60 Teardown-timer: Configured:20 Actual:20
Service load information: Average Average Peak Average Service Name Load Number ResponseTime Response Time ----------------------------------------------------------------------- DNS1 4 8999 33972 DNS2 4 8884 28254 SSH-WPHGT11 2 0 87509 WPHGT11 2 0 0 def-gwy-server 255 0 0 fe1-gw1-radius1 2 0 0 fe1-gw1-radius2 2 0 0 fe1-gw1-wap-8799 8 15344 662337 fe1-gw1-wap-9200 2 [Code].....
I’m wondering if there is a way to configure CSS11503 running 8.10 so that the servers in the content rules can see the client port number?The servers can see the client IP, but not the port!! It seems when forwarding packets to the servers in the content rule, the CSS uses a new high-number port when communicating with servers.
We have a CSS11503 that is currently being used to accept incoming HTTPS and SSH connections on a specific VIP and then PAT those client connections. I understand that it also PATs the server initiated connections. [code]
What is the equivalent of the command "show flash" in IOS for the CSS11503 as I would like to view available flash space on the CSS11500 series load balancers?
I have 5 workstations with 2 servers but the backup server (black) is shut down intentionally.I have 1 cisco gigabit unmanaged 8 port switch and 1 cisco 1941 vpn router.The cisco 1941 vpn router is configured for IPVPN connection to other branches.
Challenge:
1. Configure NAT to enable the 5 workstations to be connected to the internet thru the router to the ISP. 2. Configure NAT to enable the server to be accessed from outside using the public IP address provided by the ISP. [code]
Verification:
1. I can ping other pc on 10.71.5.0/24 network. 2. When I typed in the ISP's public ip address on the browser, i got into the modem user interface for configuration.
I still can't connect to the internet. When i do tracert, it stops on the 192.168.15.1 hop and didnt continue. This shouldn't be the case since i want to connect using the GE0/1 outside port for the internet.
I just purchased an ASA 5555 and started to configure. I was successful in natting all the IPs that are on the same subnet as the ASA eth0. I could not get the nat working for the 2nd address block.
I have a virtual machine running in my desktop which connected on the gigabit lan port on EA4500 with firmware 2.0.37.What I want to be able to do forward a port that came from an external ipv4 address to the ipv6 address and a different port to my virtual machine (to remote desktop port 3389).The reason I want to convert the traffic to ipv6 is because virtual machine is running vpn and is not reacheable through ipv4 (unless bunch of routes are setup and things get complicated etc). I verified my phsical server and virtual server get both ipv6 ip addresses through ipv6 tunnel from comcast. Without tunneling I could not get ipv6 setup using automatic mode with comcast, it simply did not work for some reason.
i have Cisco 1941(with security lic) and i have been asked to make a VPN with public IP addresses so there will be no info about internal networks. Other side has ASA 5520 and they provided me with 2 public IP addresses. i have done many different VPNs but this is first with public IP addresses and i cannot figure it out.So here is the question:
We are going to setup a L2L VPN with a vendor and they asked us to NAT a couple IP addresses for remote access to a couple of servers on our inside network. Our device is an ASA 5580 with version 8.1 and we have a handfull of public IP addresses for use if needed. The vendor's remote network is a public IP address but for this posting I will use 192.168.10.0. Our inside servers are 10.100.10.20 and 10.100.10.30. Because 10.100.10 is in use with another customer they asked us to NAT 10.77.97.20 and 10.77.97.30 to the two inside servers.
I think the subject gives a good first impression of what I'd like to achieve.Anyway i'll give a little more context.I'm running a Windows Home Server in my LAN and I would like to use it's functionalities (especially the streaming) features from "anywhere" using the same URL.My is a Linksys WRT160Nv3 running on the DD-WRT v24-sp2 firmware.I've already setup the necessary port forwardings, as most of the WHS sites run on ports 80 (http) and/or 443 (https) and my isp is blocking all ports < 1024 (I know it suck, but nothing to do about)Anyway, outside my network (friends home, work, ...) I can access my home server browsing to ://xxx.homeserver.com:10080 or https://xxx.homeserver.com:10443What I want is that this (external) DNS also works when i'm inside my network (so when I'm at home).
Is this possible?I want this because on the home page of the WHS web interface, I have some links (for example to sabnzb, or the webpage of my raid controller, etc etc, but they all point to http://xxx.homeserver.com:These url's (with the external dns) are not working when i'm inside my lan.I'm not an export but i'm quite sure it's a DNS issue.Some more info:When i do an nslookup xxx.homeserver.com I see the (external) static IP that has been assigned to my router.When I do a ping to xxx.homeserver.com I also get a reply from the (external) static ip that has been assigned to my router.
On an 887VA running 15.x IOS, is there a way to support both public and private addresses on inside vlans? The outside interface is public static ip, so the requirement would be to not nat anything if coming from inside vlan10 but nat if coming from inside vlan20.I didn't think this was possible since the outside interface would have to use an outside nat command that would not be ignored for traffic coming from vlan10.
DNS resolution works and I can surf the web without fail. But if I try to ping any external hosts (I can ping inside interface of ASA fine) from the LAN I get timeouts. I can ping anything from the ASA without fail.
I also want in internal NAT, but only for certain external hosts, so when they connect to any of the above, their source address is changed. I've attempted the following so an external host (172.16.2.254), has it's source changed to 172.16.1.100.
I have a 1760-v router set up at my home lab and I am unable to access IP addresses outside my local network. I have my Cisco router's fast Ethernet port connected to a small net gear router which then connects to my cable modem. The Cisco router is able to ping local address fine, but when I try to ping an outside address or domain name it times out. However, when I am at the CLI and type something like Ping { URL}, it resolves Google's IP address but it will not ping it. I have IP DEFAULT-GATEWAY and IP NAME-SERVER both pointing to my net gear router and pointing to my ISP's DNS server.
I'm am using Google Analytics for my webpage, and I want to exclude(filter) the IP range of my router's external IP addresses from the Analytics data. How do I determine the IP range of my router's public IP?
I currently have DCHP server set up on my new 1141N. Everything works great, but I wanted to know if it were possible to make the DHCP server only hand out ip addresses on the wireless connection? Currently the AP is giving out ip addresses from the pool to wired and wireless pc's.
I purchased a wireless bridge D-Link DAP-1522 (IP fix 192.168.0.50) to share the Internet connection to two remote devices: WD TV Live HD (IP fix 192.168.0.52) and a Samsung BD P2500 player (IP fix 192.168.0.51: to try the BD-Live) but when I plug it into my network I have an IP conflict and I can not navigate anywhere, even by the computer which control the Netgear router (IP 192.168.0.1 DHCP range 192.168.0.2-192.168.0.49).
I tried with all fixed IP (192.168.0.xxx Subnet mask 255.255.255.0 Gateway 192.168.0.1 DNS 192.168.0.1), but nothing to do, I have the same problem: after a few minutes after plugged the network cable into BD player the network falls.With wired connection (10 m of patch cable!!!) Samsung BD P2500 have no problem (DHCP and IP fix).
Then look closely in the information relating to devices connected to the Netgear router I noticed that all devices connected through the bridge DAP-1522 have the different IP but same MAC address and I think this could be the cause of the problem that creates the Blu Ray when it's connected to the network through the bridge, because he is not identified with any name but only as UNKNOWN as the bridge (a problem that WD Live not seen: same MAC address but is identified by name as WDTVLIVE).
How can I make the MAC addresses from the bridge will be recognized separately from my router/modem Netgear?In the settings of the bridge I noticed that you can enable or disable MAC address cloning, but if the off I would expect that cloning was not done and instead all the devices are identified by the Netgear router with the MAC address of the access bridge.The DAP-1522 masked the MAC address of device that are plugged into bridge.The router has the latest available firm while the original bridge has version 1.20 (the penultimate version available).
I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG. I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP table from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address.
FW1 - CONFIGURATION
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0
if possible with the RV042.Primary External IP address uses port forwards for some ports, all okay.I would like to have other external ip addresses assigned to machines on my lan.Basic host multiple web servers, on different IP addresses, using port 80. [code]
From what i am reading, it looks like the RV042 can do this, but I am not real clear what my rules should look like.
I would think my high priority rule for each external IP address would be to deny all traffic first for each machine on the lan.Then create one entry with source 202.x.x.2 port 80 -> 192.168.168.2 ?
How should I set my rules to do this, and what settings should I have on the Nic of the second machine?
How do i tell my firewall to start listen also on another outside ipadress assigned by my ISP? I have it used on other firewall right now. So my steps would be shutting down ip address assignment off old firewall interface. Assign that ip address to ASA5510 outside interface and configure NAT.
I am a total Cisco novice who has just had a ASA5505 installed to replace a linux freeware firewall (smoothwall).I'm told that the 5505 can't port forward traffic (e.g. ssh) from two external IP addresses to two internal destination machines via the same port # (22 in this example).
Trying to get a service setup with a third party to access our system (ERP web service to access our ERP data, making data available to customers and vendors via internet). They require that I setup four external IP addresses to have access through the firewall. I haven't figured out how to do this. I'm using a Linksys WRV200 router.
I recently cut over from a WRT54G to a RV120W. I am having an issue where I type [URL] (for a server running on my network) in my web browser while on the internal network and it always comes back with the router login page. Basically it is supposed to go out of the router and then come back in on the public IP address and hit that server. There was a function on the WRT54G called "Filter Internet NAT redirection" which when turned off would allow this to happen. I am not seeing a feature like this on the RV120W
I have an old ASA 5505, and I'm having some trouble with Nat Hairpinning. I've done this with other firewalls before and I am having no luck now. I have an internal address that I wish to forward from an external address- so if someone goes to 123.456.789.012:3456 then it will forward to 192.168.1.244:92 (All numbers are arbitrary here- only for illustration). I have and Access Rule and NAT and PAT set up so that I can get in if I originate from outside the LAN. What I am trying to do is to have this work from inside the LAN as well- so that if I am at my desk, and I connect a device and type in 123.456.789.012:3456, it will deliver the content at 192.168.1.244:92. The problem I am having is that it just isn't working, and I cannot figure out why- When I started here, there was an address configured to work this way, and it still works- I just cannot find what is different between what I am doing and what the person who configured it did.
