Cisco Firewall :: 5580 Need To NAT Addresses To Inside Servers
Jul 7, 2012
We are going to setup a L2L VPN with a vendor and they asked us to NAT a couple IP addresses for remote access to a couple of servers on our inside network. Our device is an ASA 5580 with version 8.1 and we have a handfull of public IP addresses for use if needed. The vendor's remote network is a public IP address but for this posting I will use 192.168.10.0. Our inside servers are 10.100.10.20 and 10.100.10.30. Because 10.100.10 is in use with another customer they asked us to NAT 10.77.97.20 and 10.77.97.30 to the two inside servers.
View 2 Replies
ADVERTISEMENT
Apr 30, 2013
I am trying to get two external addresses to PAT to different ports on the same address in the dmz.
Object NAT is configured as follows:
object network Obj-192.168.1.20-1
nat (dmz,outside) static Obj-External-1 service tcp https https
object network Onj-192.168.1.20-2
nat (dmz,outside) static Obj-External-2 service tcp 2000 https
Obj-192.168.1.20-1 and Obj-192.168.1.20-2 contain the same host address.
The idea being that traffic destined for Obj-External-1 on port 443 will be forwarded to Obj-192.168.1.20-1 on port 443. Traffic for Obj-External-2 on port 443 will be forwarded to Obj-192.168.20-2 on port 2000.
Traffic for the first object, Obj-192.168.1.20-1, works but traffic for the second does not.
View 5 Replies
View Related
May 6, 2011
I have a PIX 515E that I want to use to as a border between my internet connection and my Cisco AIR1131AG. I have configured the PIX to have the outside interface as a dhcp client which gets its dynamic IP address from the cable modem. the AP is connected to the E1 inside interface. Now I could see the E1 interface from the arp table from the AP but I cannot ping it. From the firewall I don't see the ARP table from the firewall. and i cannot ping the AP. what is wrong with the configuration? side note, i am able to connect to the AIR1131AG from my laptop I was not able to retrieve an IP address.
FW1 - CONFIGURATION
interface Ethernet0 description uplink towards the techsavvy modem speed 100 nameif outside security-level 0 ip address dhcp setroute !interface Ethernet1 description >>> WIFI LAN ACCESS <<< nameif inside security-level 100 ip address 10.0.0.1 255.255.255.0
[Code].....
View 3 Replies
View Related
Aug 8, 2012
I have a customer with an 877ISR with zone base firewall. They want to access two servers on the inside from the internet using RDP but with different ports.
Partial configuration.
interface Dialer0
description $FW_OUTSIDE$
ip address negotiated
no ip redirects
no ip unreachables(code)
View 4 Replies
View Related
Oct 30, 2012
Got an ASA5525-X with 8.6 release. We have an inside interface (10.11.1.0/24) and a DMZ interface (10.254.1.0/24). On that DMZ interface theres an SMTP server; by using the Public server feature in ASDM we created a rule so we have mapped the 10.254.1.29 internal ip to an external ip 217.x.x.x Everything is fine; working ok, but for several reasons we need to access the public ip 217.x.x.x from an inside ip (10.11.1.10). I tried to do it by creating an exemption for the dynamic nat; if i don't do that i have a 'deny ip spoof from...' message rolling on my syslogs.Seems to do the trick.....but only for pings! i ping the public ip from the inside ip, and got the reply from the internal ip on the DMZ. But if i want to telnet port 25 from inside to public; its not working.
View 7 Replies
View Related
Nov 27, 2012
On an 887VA running 15.x IOS, is there a way to support both public and private addresses on inside vlans? The outside interface is public static ip, so the requirement would be to not nat anything if coming from inside vlan10 but nat if coming from inside vlan20.I didn't think this was possible since the outside interface would have to use an outside nat command that would not be ignored for traffic coming from vlan10.
View 4 Replies
View Related
Dec 8, 2011
I know the CSS is too old but I have one in production environment and I was asked if it is possible to CSS to make NAT from inside addresses and translate them into one external IP address to diferent kind of communications, for example: 172.16.4.9 and 172.16.4.10 (inside addresses) should start connection to external IP addresses destinations 50.50.50.50 / 60.60.60.60 70.70.70.70 / 80.80.80.80 and so on, the default gateway to those Servers is the CSS and I would like to know if it is possible that all connection to external world to be translate into one IP address 172.16.4.100.
My CSS is 11503
Version: sg0810106
View 2 Replies
View Related
Dec 20, 2011
nslookup shows all ip addresses of a nic. is this expected? i think it should just show the default IP
View 3 Replies
View Related
Jul 5, 2011
Got a problem accessing our webservers on the inside interface from other clients on the inside interface on our ASA 5505.As in, they type in url... in their browser, and it wont work.
However, if we use a PC on another outside network, it works just fine! [code]
View 2 Replies
View Related
Feb 15, 2012
We have ASA 5550, I have a citirx server in the dmz which is natted statically to a public ip address for port 443. The dmz server communicate with our internal server (i.e. AD) for LDAP authentication. I have a static transparent nat from inside to dmz for the internal server's communcation with dmz.
When accessing the application from inside the network on the internal web server it works perfectly fine and authenticates with the AD.But when accessing from outside, the reach the citrix server and then the AD authentication fails, basically it works intermitantly. I have tried to check the communcation from the DMZ server to the internal server and the icmp works perfectly fine, even I am able to telnet on the ports specified on the internal servers from the DMZ servers. I tried to look into the logs on the ASA and this is something that looks suspicious to me.
Feb 16 Teardown TCP connection 47646475 for dmz1:CITRIX-DMZ1/47179 to inside:inside-server/80 duration 0:00:00 bytes 1230 TCP FINs
Feb 16Built inbound TCP connection 47646476 for dmz1:CITRIX-DMZ1/47180 (CITRIX-DMZ1/47180) to inside:inside-server/80 (inside-server/80)
Feb 16Teardown TCP connection 47646476 for dmz1:CITRIX-DMZ1/47180 to inside:inside-server/80 duration 0:00:00 bytes 3824 TCP FINs
Feb 16Built inbound TCP connection 47646477 for dmz1:CITRIX-DMZ1/47181 (CITRIX-DMZ1/47181) to inside:inside-server/80 (inside-server/80)
Feb 16 Teardown TCP connection 47646477 for dmz1:CITRIX-DMZ1/47181 to inside:inside-server/80 duration 0:00:00 bytes 1224 TCP FINs
[code]....
View 2 Replies
View Related
Apr 18, 2012
We are going to impliment Spectrum (CA) in my network,i have ASA-5580-20 firewall now my spectrum server want to communicate with firewall,then only it will discover the firewall logs.Now the problem is my spectrum server is in MZ zone(10.10.10.45) security leval is 70 and my inside interface(10.20.20.101) security leval is 100.
I am unable to ping from spectrum server to firewall because of high security leval.How can i solve this problem,can i change my inside security leval to 69 then i think it will ping.
View 1 Replies
View Related
Oct 30, 2011
i check ASR 1006 config with ESP-40, the firewall permonce can reach 40G, ASA 5580 is 20G, can ASR 1006 replace ASA 5580, is there any function feature problem?
View 1 Replies
View Related
Oct 13, 2010
I recently cut over from a WRT54G to a RV120W. I am having an issue where I type [URL] (for a server running on my network) in my web browser while on the internal network and it always comes back with the router login page. Basically it is supposed to go out of the router and then come back in on the public IP address and hit that server. There was a function on the WRT54G called "Filter Internet NAT redirection" which when turned off would allow this to happen. I am not seeing a feature like this on the RV120W
[URL]
View 29 Replies
View Related
Oct 15, 2011
accessing my cisco ASA, last night we were doing VA on our ASA, after that iam not able to access it through ssh nor telnet. its not giving me any error.. i tried from different system also. SSH & telnet allowed from inside to 0.0.0.0 i have re-generated rsa keys when it was working. ASA version is 8.2 now when i connect telent is giving me blank prompt. i can login using ASDM.
View 5 Replies
View Related
Sep 27, 2011
I got a problem with a cisco asa 5580 like two days ago and the device stop working (there was a mainteinance window and after that the device didn't work). Now we receive the RMA and we are trying to configure the failover so the new device get the configuration form the one that is working.
But this is the message that I gettin:
Failover message decryption failure. Please make sure both units have the same failover shared key and crypto license or system is not out of memory
We already changed the shared key and crypto license but the failover is still down, what are the features that the cisco need to activate to enable the failover?
View 5 Replies
View Related
Feb 11, 2012
I am receiving allot of Errors "%ASA-4-405001: received ARP collision from IP/MAC on interface dmz1 with existing ARP Entry IP/MAC
When i checked this MAC address in the same firewall it shows too many IP Addresses. What could be the reason ?
View 0 Replies
View Related
May 23, 2012
We are using Cisco ASA 5580 (8.2) firewall. When i try to ping from inside lan to firewall DMZ interface IP it is not pingable and but from inside users i am able to ping firewall inside interface IP address.
I think we can't ping to other interfaces of ASA by default. But can we allow the single IP address who can ping all the interfaces of firewall?
We are not doing any natting in firewall, for that we used the Load Balancer.
View 7 Replies
View Related
May 16, 2011
A customer's ASA is presenting the System LED flashing red.I have already analysed the show tech-support and show environment output: Found nothing, everythink seems OK.Cisco ASA 5580-20 - 8.2.1.Single appliance, no failover, multiple context and transparent mode.
View 5 Replies
View Related
Aug 19, 2012
we are going to upgrade our 5580 ASA Cluster from 7.2 to 8.2 and want to do it like this way ( which worked for all 7.x upgrades ) :download asa8.2 Image to primary + secondary Firewallreboot primary ( message come up " mate version ...)reboot secondary.Does it works any experience? Does it work if both firewall can see each other during the boot process ?
Do I have to bring the secondary into the monitor mode so the fw is not visible for the primary ?
View 2 Replies
View Related
Mar 29, 2011
I want to ask that does ASA 5580 support the nat-pt for IPv6?
View 2 Replies
View Related
Mar 5, 2011
i'm new with the asa's...i'm familiar with the FWSM's on 6500's and pix..I'm running Version 8.3(2) and i wanted to setup nat-control and use of identify nats for advertising inside subnets to my outside networks.
the old command was static(inside,outside) 10.x.x.x 10.x.x.x netmask 255.255.255.x i'm having a little difficulty decyphering the pdf about the static nat...the command itself is no longer used, nat-control is no longer used, but i'm not quite sure what the equivalent nat command is that equates to the old static inside,outside command.
View 8 Replies
View Related
Apr 8, 2012
In my ASA 5580-20 system LED is flashing RED how can i trobleshoot this.
I checked rarepanel everything is ok also i saw environment also showing ok
View 1 Replies
View Related
Jun 11, 2013
We are planning to split the Private servers from the DMZ Servers and configure an additional Interface and segment for this purpose.
Private Servers Segment: 192.168.4.0/24 (there is no DHCP all servers' IPs are statically configured)
DMZ Segment: 192.168.3.0/24 (This is a future deployment)
LAN Segment: 172.17.0.0/16
Both, Private Servers and DMZ Servers are in a collocation as well as the ASA5520. There are multiple Branch offices that uses subnets within the 172.17.0.0/16 Network and they are connected to the ASA5520 via Metro-E.
I do not know if this is possible but what I want to do is this:
In order to avoid the change of internal DNS records I want to mask the DMZ servers with a Private Server IP when a Private server or LAN host wants to access it like this:
The FTP server in the DMZ has the IP address: 192.168.3.100. But when a PC from the LAN wants to reach the FTP server it should points to its old IP: 192.168.4.100. This way the PC sends a packet to the ftp.corporate.net (192.168.4.100) the ASA recieves the packet and translate it to the (192.168.3.100) and send it out through the DMZ Interface.
Also if the Private Servers wants to reach the same FTP the ASA will act like a proxy-ARP and send the paquet to the DMZ by means of the translation of the IP.
View 6 Replies
View Related
Feb 19, 2012
I have encountered a problem in one of customer that the Active ASA 5580 is unable to sync with Standby Failover ASA. When Active is connected with FO and push the configs to it will not find the ethernet/Gig interfaces due to which the all the configuration were not applied and when the primary ASA the secondary is unable to respond.
When i attached console with the Standby ASA i have seen this error.
Number of interfaces on Active and Standby are not consistent.If the problem persists, you should disable and re-enable failover on the Standby.
For detail undestanding i am attaching the configs of primary and standby ASA. The KHI-DR-ASA-BB-01 is the standyby firewall.
View 2 Replies
View Related
Jul 11, 2012
If we switch from primary to secondary firewall the interfaces on the secondary go to state waitung than to failed. after awhile the secondary gives the control to the primary.
it seem that traffic passes the secondary firewall during this short failover time . we have several context created on the firewall, Switch Ports checked , cabeling check everythink checked
blackhole Interface inside (10.255.102.134): Normal (Waiting)
blackhole Interface shared (10.255.102.134): Normal (Waiting)
blackhole Interface inside (10.255.102.133): Failed (Waiting)
blackhole Interface shared (10.255.102.133): Normal
blackhole Interface inside (10.255.102.133): Normal (Waiting)
blackhole Interface shared (10.255.102.133): Normal
View 5 Replies
View Related
Nov 23, 2011
We got a replacement ASA 5580 from Cisco. We were not aware of PAK, Is there any other possible to generate Activation key? Can we generate PAK or Activation Key using SO (service order) number?
View 1 Replies
View Related
Dec 21, 2011
I have a problem with failover. On My site I have 2 Firewalls 5580. And I did this configuration on my firewall.interface GigabitEthernet3/0description LAN/STATE Failover Interfacespeed nonegotiate.
View 5 Replies
View Related
Jun 14, 2012
I have two firewalls in 2 different locations. They act as primary and secondary for my WAN connectivity. I would want a way to synchronize access-lists in both without manually replicating.(access list, NAT and Route)FW model cisco 5580
View 1 Replies
View Related
Apr 4, 2012
We have a Cisco ASA 5580 and the outside interface has a public IP address and we noticed we can ping this address from the Internet. I did a packet capture on the outside interface and confirmed the pings and the IP address sending the pings. The 5580 does not have an access list allowing icmp so I'm not sure what is allowing the pings to this interface.
View 5 Replies
View Related
Oct 3, 2011
The firewall is running version #8.2 on ASA 5580. Address translation is not needed on Inside network and Outside network.But the customer has hundreds of static command as below.. [code] Can they all be removed and replace with one single command as below?
View 1 Replies
View Related
Oct 31, 2011
Does ASA supports NAT in bridge mode? especially the 5580 series x??
View 1 Replies
View Related
May 1, 2012
I have got new cisco ASA 5580 running 7.2(4) on it when i am trying to configured Virtual interface on vlan 400 in Gi0/0.400 to LBASE.now the problem is from my MZ zone 10.242.107.17 to Lbase virtual interface 10.242.103.1 iam not able to ping.
View 2 Replies
View Related
Sep 13, 2011
This is the situation I got to firewalls with failover and I need to upgrade the license so I can get more context (right now I have 5 context and I need 10) so I was looking at the procedure and I'm not sure If I need to restart the device or not. I was looking at this procedure:
Upgrading the License for a Failover using ASDM (No Reload Required) Use the following procedure using ASDM if your new license does not require you to reload. This procedure ensures that there is no downtime.
•1. On the active unit, choose Configuration > Device Management > High Availability > Failover > Setup, and uncheck the Enable Failover check box. Now click Apply. The standby unit remains in a pseudo-standby state. Deactivating failover on the active unit prevents the standby unit from attempting to become active during the period when the licenses do not match. •
2. Choose Configuration > Device Management > Licensing > Activation Key, and enter the new activation key that you obtained with the active unit serial number. Now click Update Activation Key.•
3. Log into the standby unit by double-clicking its address in the Device List. If the device is not in the Device List, click Add to add the device. You might be prompted for credentials to log in.
4. Choose Configuration > Device Management > Licensing > Activation Key, and enter the new activation key that you obtained with the standby unit serial number. Now click Update Activation Key.
5. Log into the active unit again by double-clicking its address in the Device List. Choose Configuration > Device Management > High Availability > Failover > Setup, and re-check the Enable Failover check box.
6. Click Apply. This completes the procedure.link: [URL]
But then I checked on the cisco web page that there are some license that need to reload I see this:
All models
#Downgrading any license (for example, going from 10 contexts to 2 contexts).#Note If a temporary license expires, and the permanent license is a downgrade, then you do not need to immediately reload the security appliance; the next time you reload, the permanent license is restored.
[URL]
So I just want to know if I'm UPGRADING from 5 to 10 context the reload applies to my situation or not?
View 1 Replies
View Related
