We have a Cisco ASA 5580 and the outside interface has a public IP address and we noticed we can ping this address from the Internet. I did a packet capture on the outside interface and confirmed the pings and the IP address sending the pings. The 5580 does not have an access list allowing icmp so I'm not sure what is allowing the pings to this interface.
View 5 Replies
We are using Cisco ASA 5580 (8.2) firewall. When i try to ping from inside lan to firewall DMZ interface IP it is not pingable and but from inside users i am able to ping firewall inside interface IP address.
I think we can't ping to other interfaces of ASA by default. But can we allow the single IP address who can ping all the interfaces of firewall?
We are not doing any natting in firewall, for that we used the Load Balancer.
We are going to impliment Spectrum (CA) in my network,i have ASA-5580-20 firewall now my spectrum server want to communicate with firewall,then only it will discover the firewall logs.Now the problem is my spectrum server is in MZ zone(10.10.10.45) security leval is 70 and my inside interface(10.20.20.101) security leval is 100.
I am unable to ping from spectrum server to firewall because of high security leval.How can i solve this problem,can i change my inside security leval to 69 then i think it will ping.
VPN between datacentre & office ASA 5510 & HP routers site-to-site vpn, 192.168.1.0 и 172.16.0.0 networks If I ping internal routers' cisco address 192.168.1.1 from 172.16.0.0 network host (172.16.2.200) I get ping timeout At the same time I see the same messages in ASDM monitoring when successful ping reaches and comes back to 192.168.1.0 host (192.168.1.101 for example) Pings from 172.16.0.0 to 192.168.1.0 hosts are ok, only 192.168.1.1 is silent Looks like icmp echo reply is not allowed or smth like that, where to take a look?why monitoring looks ok instead of denied according to ACL...?
View 2 Replies View Relatedhow my switches are configured, a cisco 3750 and a cisco 4506.[code] i can ping the gateway from the 3750 however cannot get anything past that or enything to it.
View 12 Replies View Relatedi check ASR 1006 config with ESP-40, the firewall permonce can reach 40G, ASA 5580 is 20G, can ASR 1006 replace ASA 5580, is there any function feature problem?
View 1 Replies View Relatedaccessing my cisco ASA, last night we were doing VA on our ASA, after that iam not able to access it through ssh nor telnet. its not giving me any error.. i tried from different system also. SSH & telnet allowed from inside to 0.0.0.0 i have re-generated rsa keys when it was working. ASA version is 8.2 now when i connect telent is giving me blank prompt. i can login using ASDM.
View 5 Replies View RelatedI am using an ASA5550 for a complex secure network that has at least six "outside" networks. Each "outside" network is assigned to a specific port each set at level "0". I also have a DMZ, set to level "50". I am having difficulty with passing traffic from a host in the DMZ to all but one of the "outside" networks. Is there a limit to the number of "outside" interfaces? I will provide a redacted config file as soon as possible.
View 3 Replies View RelatedA user needs to be allowed through the Cisco ASA 5505 firewall to make a VPN connection to 83.1.**.** address on port 1723.
View 13 Replies View RelatedI was reviewing my ASA config and noticed that port 1025 was being allowed in and statically NAT'd to connect to my email server:
access-list outside_in extended permit tcp any host X.X.X.X eq 1025
static (inside,outside) tcp interface 1025 Y.Y.Y.Y 1025 netmask 255.255.255.255.
I got a problem with a cisco asa 5580 like two days ago and the device stop working (there was a mainteinance window and after that the device didn't work). Now we receive the RMA and we are trying to configure the failover so the new device get the configuration form the one that is working.
But this is the message that I gettin:
Failover message decryption failure. Please make sure both units have the same failover shared key and crypto license or system is not out of memory
We already changed the shared key and crypto license but the failover is still down, what are the features that the cisco need to activate to enable the failover?
I am receiving allot of Errors "%ASA-4-405001: received ARP collision from IP/MAC on interface dmz1 with existing ARP Entry IP/MAC
When i checked this MAC address in the same firewall it shows too many IP Addresses. What could be the reason ?
A customer's ASA is presenting the System LED flashing red.I have already analysed the show tech-support and show environment output: Found nothing, everythink seems OK.Cisco ASA 5580-20 - 8.2.1.Single appliance, no failover, multiple context and transparent mode.
View 5 Replies View Relatedwe are going to upgrade our 5580 ASA Cluster from 7.2 to 8.2 and want to do it like this way ( which worked for all 7.x upgrades ) :download asa8.2 Image to primary + secondary Firewallreboot primary ( message come up " mate version ...)reboot secondary.Does it works any experience? Does it work if both firewall can see each other during the boot process ?
Do I have to bring the secondary into the monitor mode so the fw is not visible for the primary ?
I want to ask that does ASA 5580 support the nat-pt for IPv6?
View 2 Replies View Relatedi'm new with the asa's...i'm familiar with the FWSM's on 6500's and pix..I'm running Version 8.3(2) and i wanted to setup nat-control and use of identify nats for advertising inside subnets to my outside networks.
the old command was static(inside,outside) 10.x.x.x 10.x.x.x netmask 255.255.255.x i'm having a little difficulty decyphering the pdf about the static nat...the command itself is no longer used, nat-control is no longer used, but i'm not quite sure what the equivalent nat command is that equates to the old static inside,outside command.
In my ASA 5580-20 system LED is flashing RED how can i trobleshoot this.
I checked rarepanel everything is ok also i saw environment also showing ok
i allowed one of internal ip using static nat and public ip is 203.18.137.22 and i want to check which IP are hit this public ip ?Is there is any command to check which ip is hitting 203.18.137.22? I have the cisco 5520 asa firewall.
View 6 Replies View Relatedi have reviewed this configuration a couple of times and I am not seeing my error. I have two internal subnets, in different VLANs with the ASA being the default router. The internal zone works fine, but the zone called wireless on VLAN 13 doesn't. The firewall blocks all communications and the rules look correct to me. I want all traffic on this wireless subnet to be allowed to cross over the firewall and NAT to the outside interface, just as the inside zone does.
View 1 Replies View RelatedI would like to setup an cisco ASA 5505 to only allow certain IP's on port 3389, but i can't get it to work. Maybe some of you experts know why?
Here is my config:
ASA Version 8.4(3)!hostname cisco-asaenable password ** encryptedpasswd ** encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface Ethernet0/2!interface Ethernet0/3!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!interface Vlan1nameif insidesecurity-level 100ip address 192.168.1.253 255.255.255.0!interface Vlan2nameif outsidesecurity-level 0ip address 95.*.*.* 255.255.255.248!ftp mode passiveobject network obj_anysubnet 0.0.0.0 0.0.0.0object network rdpuser-1host 46.*.*.*object network rdpuser-2host 48.*.*.*object network rdp-host-pchost 192.168.1.20object
[code].....
The allowed IP's are setup on user level (rdpuser-1 and rdpuser-2) .Still do, I can't connect to the server from any of these IP's...
Port forwarding done to a DMZ located server on the cisco ASA 5520. Now this host cannot browse but allowed outside to inside access is possible Is there anyway i can give this system to browse internet? may be through the natted IP ( 94.20.*.*)
View 2 Replies View RelatedI have encountered a problem in one of customer that the Active ASA 5580 is unable to sync with Standby Failover ASA. When Active is connected with FO and push the configs to it will not find the ethernet/Gig interfaces due to which the all the configuration were not applied and when the primary ASA the secondary is unable to respond.
When i attached console with the Standby ASA i have seen this error.
Number of interfaces on Active and Standby are not consistent.If the problem persists, you should disable and re-enable failover on the Standby.
For detail undestanding i am attaching the configs of primary and standby ASA. The KHI-DR-ASA-BB-01 is the standyby firewall.
If we switch from primary to secondary firewall the interfaces on the secondary go to state waitung than to failed. after awhile the secondary gives the control to the primary.
it seem that traffic passes the secondary firewall during this short failover time . we have several context created on the firewall, Switch Ports checked , cabeling check everythink checked
blackhole Interface inside (10.255.102.134): Normal (Waiting)
blackhole Interface shared (10.255.102.134): Normal (Waiting)
blackhole Interface inside (10.255.102.133): Failed (Waiting)
blackhole Interface shared (10.255.102.133): Normal
blackhole Interface inside (10.255.102.133): Normal (Waiting)
blackhole Interface shared (10.255.102.133): Normal
We got a replacement ASA 5580 from Cisco. We were not aware of PAK, Is there any other possible to generate Activation key? Can we generate PAK or Activation Key using SO (service order) number?
View 1 Replies View RelatedI have a problem with failover. On My site I have 2 Firewalls 5580. And I did this configuration on my firewall.interface GigabitEthernet3/0description LAN/STATE Failover Interfacespeed nonegotiate.
View 5 Replies View RelatedI have two firewalls in 2 different locations. They act as primary and secondary for my WAN connectivity. I would want a way to synchronize access-lists in both without manually replicating.(access list, NAT and Route)FW model cisco 5580
View 1 Replies View RelatedThe firewall is running version #8.2 on ASA 5580. Address translation is not needed on Inside network and Outside network.But the customer has hundreds of static command as below.. [code] Can they all be removed and replace with one single command as below?
View 1 Replies View RelatedWe are going to setup a L2L VPN with a vendor and they asked us to NAT a couple IP addresses for remote access to a couple of servers on our inside network. Our device is an ASA 5580 with version 8.1 and we have a handfull of public IP addresses for use if needed. The vendor's remote network is a public IP address but for this posting I will use 192.168.10.0. Our inside servers are 10.100.10.20 and 10.100.10.30. Because 10.100.10 is in use with another customer they asked us to NAT 10.77.97.20 and 10.77.97.30 to the two inside servers.
View 2 Replies View RelatedDoes ASA supports NAT in bridge mode? especially the 5580 series x??
View 1 Replies View RelatedI have got new cisco ASA 5580 running 7.2(4) on it when i am trying to configured Virtual interface on vlan 400 in Gi0/0.400 to LBASE.now the problem is from my MZ zone 10.242.107.17 to Lbase virtual interface 10.242.103.1 iam not able to ping.
View 2 Replies View RelatedThis is the situation I got to firewalls with failover and I need to upgrade the license so I can get more context (right now I have 5 context and I need 10) so I was looking at the procedure and I'm not sure If I need to restart the device or not. I was looking at this procedure:
Upgrading the License for a Failover using ASDM (No Reload Required) Use the following procedure using ASDM if your new license does not require you to reload. This procedure ensures that there is no downtime.
•1. On the active unit, choose Configuration > Device Management > High Availability > Failover > Setup, and uncheck the Enable Failover check box. Now click Apply. The standby unit remains in a pseudo-standby state. Deactivating failover on the active unit prevents the standby unit from attempting to become active during the period when the licenses do not match. •
2. Choose Configuration > Device Management > Licensing > Activation Key, and enter the new activation key that you obtained with the active unit serial number. Now click Update Activation Key.•
3. Log into the standby unit by double-clicking its address in the Device List. If the device is not in the Device List, click Add to add the device. You might be prompted for credentials to log in.
4. Choose Configuration > Device Management > Licensing > Activation Key, and enter the new activation key that you obtained with the standby unit serial number. Now click Update Activation Key.
5. Log into the active unit again by double-clicking its address in the Device List. Choose Configuration > Device Management > High Availability > Failover > Setup, and re-check the Enable Failover check box.
6. Click Apply. This completes the procedure.link: [URL]
But then I checked on the cisco web page that there are some license that need to reload I see this:
All models
#Downgrading any license (for example, going from 10 contexts to 2 contexts).#Note If a temporary license expires, and the permanent license is a downgrade, then you do not need to immediately reload the security appliance; the next time you reload, the permanent license is restored.
[URL]
So I just want to know if I'm UPGRADING from 5 to 10 context the reload applies to my situation or not?
I have a asa5580 with multiple interfaces. To replicate me databases to another site, I mainly use two interfaces on that firewall. Those interfaces have a steady pace, around 95%.
I am wondering when I should consider that the thoughput between those two interfaces is too much? Is there a good document that could explain me clearly why?
Also I want to be sure that I won't affect the normal traffic between the other interfaces. Is there a way to garantee certain traffic over others on an ASA? I don't have any router in me setup layer 3 role is perform by asa firewalls (static routes).
Preparing to upgrade the IOS on a failover pair of ASA 5580's and was wandering what is gonna happen after I've upgraded the IOS on the standby unit and rebooted. How is the active unit going to react when it sees an IOS mismatch prior to me making the standby the primary and upgrading it's IOS ?
View 2 Replies View Related
