Can add feature "release" and "renew" to wan dhcp client? Is it WOL not possible in RV220w? i tried forward broadcast magic packet from wan side, change broadcast IP and through VPN tunnel (PPTP & IPSEC)...got failed i change from draytek 2130n to rv220w, 2130n much better. except SSL VPN.
View 2 RepliesI have a Linksys WRT310N v1 with firmware v1.0.10 build 002Jul 19, 2010 My router fails to renew it's DHCP lease from my cable provider, causing internet access to drop. I can still access my cable modem at 192.168.100.1, but I must do a "IP Address Release" then "IP Address Renew" to get back internet access. The router works fine otherwise.
View 6 Replies View RelatedI have a linksys EA 2700 with the latest smart wifi firmware. However, the "Release and renew" of the IPv4 internet ip is greyed out. Only IPv6 is enabled.
View 1 Replies View RelatedI've had my WRT110 for about 3 years or so, and it has worked fine for a long time. Today my computers were connecting to the router, but weren't getting internet access so I did the following:
checked lights on router and modem, they all indicated everything was working and normal Reset Modem,Reset Router,Still nothing. Called Comcast, they said everything was working fine from their end.Plugged my laptop into the ethernet connection on router.Plugged laptop directly into modem and it works fine.I saw the link on here to setup the router, and I have 0s on the internet ip, like it suggests at the end. When I click on the "release" and "renew" buttons nothing changes.
At this moment (firmware 1.0.3.5) the router has no IPv6 firewall and therefore when used in a typical dual stack IPv4/IPv6 network it has no protection regarding IPv6 traffic. Hopefully this will be fixed with a firmware update before the World IPv6 Day on the 6th of June 2012.
View 1 Replies View RelatedI have been trying to configure a local DMZ on our network with the Cisco Small Business RV220W router, running the latest 1.0.3.5 firmware but it doesn't seem to be fully functional? Does the DMZ feature actually do anything at the current state of this router? Because when I tried to DMZ host a computer on our local network I still had to manually port forward different applications in order for people to reach it from WAN.
For instance when trying to host a game session, utilizing TCP port 7777 it didn't matter whether I had enabled DMZ or not, I was still required to manually port forward the port to the DMZ IP-address.
Doesn't this defeat and eliminate the whole purpose of the DMZ feature in the first place?
From an older manual it describes how to configure this. I installed the oldest firmware available for download and this feature is there. Was this just simply moved somewhere else in the newer firmware?
Configuring Port VLANs
You can associate VLANS on the Cisco RV220W to the LAN ports on the device.
By default, all 4 ports belong to VLAN1. You can edit these ports to associate them
[Code].....
I Have RV220W Rev 1.0.3.5/I want to create 5 users adn connect remotely to the office network using a PPTP connection.
I have enabled the PPTP server and created users.From a remote location (WAN) on Windows 7, I have created a PPTP connection and I can connect however I can not ping or map to the office network.
I have a Cisco RV220W router (firmware version 1.0.4.17).
I would like to have two separate networks with the following specifications:
Netwrork1: address range for the network is 192.168.0.1-254. All devices should be able to reach eachother within this network and connect to the internet either on LAN or through Wifi. From this network I should also be able to reach the device management page of the router. Also the devices should get the ip addresses throgh DHCP.
Network2: address range for the network is 192.168.5.1-254. All devices within this network should not be able to reach the devices in network1. All devices on this network should reach the internet through Wifi only. Device management page should not be available on this network.
I have configured the router as shown in the attached screenshots but the problem is that in Network2, devices get IPs from the 192.168.0.1-254 range and not from the 192.168.5.1-254 range. Also there is no internet on these either.
Initial setup with RV220W completed without difficulty,Need to set up static IP for one of the machines in the LAN (not static IP for WAN),I presume I use the static DHCP option, which allows me to select a particular IP for the machine I select based on it's MAC,1. My confusion stems from the manual stating that "the IP address that you pick should be outside the DHCP address range specified on the Networking> LAN(local network)>IPV4(local network)page".,Does that mean that the range on the IPV4 local network page should be modified to exclude the IP address that I want to use for the static IP..e.g. change the range from 1-255 to 1-200 and then use an IP of XXX.XXX.X.201 for instanceor does that mean that as soon as I choose an IP on the Static DHCP page, that if will reserved for use only on that machine and not used for another machine on the LAN, without me having to do something else to exclude it's use (i.e. does reserving a static IP automatically remove it from the range of IPs available to other machines)If I simply set a static IP on the local machine by going to "change network adapter" settings, what's the liklihood that the router might use the same IP on another machine.
View 2 Replies View RelatedI'm wondering if it's possible to setup SSL VPN connection via OPEN VPN client?I'm a Mac OS 1.7 user with Tunnelblick.
I tried to use "built-in" SSL VPN Tunnel client but unfortunately it's not working - during installation Java exception appears saying that either I don't have admin privileges or there is not enough space.. Of course I'm admin and there is plenty of space...
My ISP waits a definite host name from me to return my white IP address via DHCP. Can I set this parameter in RV220W router? I don't find such parameter in IPv4 WAN configuration page.
View 1 Replies View RelatedI try to connect to RV220W with windows 7 client but I fail : error 789. I compare again and again pre shared key, but it doesn't change anything. How to connect to RV220W with IPsec client ?
View 4 Replies View RelatedThe establishment of IPSEC tunnel between the RV220 and QuickVPN client works properly with the security certificate of origin of the router.RV220 V1.0.3.5QuickVPN V1.4.2.1
Since the establishment of a security certificate self-signed, the RV220 and QuickVPN client refuses to work together .
Here are the log of the QuickVPN client
2011/09/27 12:45:14 [STATUS]OS Version: Windows 7
2011/09/27 12:45:14 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON
2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON
[code].....
I have a Cisco RV220W running the latest firmware (currently 1.0.4.17), and I have noticed that after about a week of use, wireless clients can no longer acquire IP addresses via DHCP.
I have used Network Monitor on both the DHCP server, and the WiFi client, and can see that the server is receiving the requests and sending a reply, but the client never sees the response from the server. So far the only way to resolve this is to reboot the router.
We assign (reserve by MAC actually) static IPs to all of our devices. Over time we have gotten rid of some devices but haven't begun (or finished really) re-using the old IPs. On our WRVS4400N v2 routers we are able to set the max number of DHCP users per Vlan. This prevents unauthorized devices trying to connect to our LAN.For example. I set the range from 192.168.1.100 - 192.168.1.103. IPs 100, 101, and 103 are in use (reserved via MAC address). We set max number of DHCP users to 3. This prevents someone from gaining access to 192.168.1.102. Does this make sense? Or at least this was the initial goal and it tested out successfully back when we implemented it.
How can I do the same for with the RV220W? I can set the range, assign static IPs (reserve IPs by MAC address), but can't keep others from gaining accessing to our LAN via the unused IPs (not assigned a static IP).My initial thought was to create static IPs (for the unused IPs) using dummy MAC addresses. I'm sure there is a much better way of accomplishing what I am trying to do.
We have
1-A wireless link (pre-wimax) that provide me with 2 Mb internet connection (tagged Ethernet frames) throught RJ-45
2-have 6 real IP _one of them as Gateway
What i need now is what is the best and cheapest device to do NAT and DHCP to allow users to access the internet , i am trying to do this using Cisco AP 1141 and the link is working fine with static ip configuration on my lap (give my wireless NIC real IP) but now i just need device to do NAT and DHCP
My suggestion is can i use Cisco RV220W Wireless-N Network Security Firewall to do this function. is the WAN port on this router support tagged Ethernet frames ??? or even untagged frames and can i give this router one of those public IPs and give the rest of those IPs statically to other devices on the network.
I have a Cisco rv220w. I just tried updating the firmware. I used RV220W-Firmware-1.0.3.5.img. It rebooted, and now there is no DHCP and no access to anything. I tried the reset button for 10 seconds. That didn't do anything. The WAN and all the LAN lights light up. Power is on and solid. The light blinks alternating between the DMZ and the blank space to the right of wireless. How can I get this back to factory defaults?
View 5 Replies View Relatedi created the 10 V LAN in my Cisco 3750 switch.All other V LAN DHCP IP's (192.168.2.X - 192.168.10.X) will be release from the DHCP server except VLAN1 . In my 3750 switch i created DHCP pool(192.168.14.X).... and i assigned to VLAN10.... but one of the client is assigned to V LAN 2(192.168.2.X) configuration. but its getting IP from the Cisco DHCP instead of DHCP server.
View 2 Replies View RelatedI have an out of the box configured RV220W and was wondering if it supports local DNS resoltuion for DHCP addresses it issues. I have a few reservations and a custon search domain configured ('local') but it will not resolve a name fromt the terminal using the search domain (see below):
It resolves freenas but not freenas.local.
macbookair:~ brantwinter$ dig freenas
; <<>> DiG 9.8.1-P1 <<>> freenas
;; global options: +cmd
[Code]...
I've heard mixed things about the use of DHCP release messages. I've heard that some operating systems don't bother with them at all, which makes sense because many users disconnect the network media without shutting down the workstation. Which operating systems actually send out release messages as part of their shutdown sequence?
View 5 Replies View RelatedI was trying to set a DHCP pool with 127.16.0.0/16 with RV220W, however, RV220W UI can't save it. It displays "IP Address Range -"Step to reproduce: (it is 100% reproducible)
1. login into RV220W admin web
2. Create a VLAN, id 201
3. Go to "Multiple VLAN subnets", select the VLAN, click edit
4. Enter following info:
IP Address: 172.16.0.1
Subnet Mask: 255.255.0.0
DHCP Mode: DHCP Server
Domain Name: Cisco
Starting IP Address: 172.16.2.100
Ending IP Address: 172.16.10.254
Primary DNS Server: 172.16.0.1
Leave rest of settings with default value.
DNS proxy is enabled
5. Press Save button. The UI shows text "IP Address Range -".
Expected result: RV220W shall save the setting and make use of 172.16.0.0 subnet in IP pool. By the way, the error message "IP Address Range -" seems incompleteI tried same setting on netgear FVS318N (very similar settings to RV220W), it accepts 172.16.0.0/16 as DHCP IP pool and works.RV220W has great feature set meets my needs. Its UI is slow and sometime dashboard freezes, which I can live with comparing to features. But DHCP server IP pool can't be class B is huge limitation to me.
I wanted to connect to the Internet but my laptop has this message: " Your IP address lease has expired. DHCP was unable to renew your lease." I cannot connect to the Internet. What should I do?
View 1 Replies View RelatedI have several Cisco WAP4410N access points. They are configured to automatically obtain an IP address through DHCP. This works fine, but I've discovered when the DHCP lease expires, the access point doesn't renew it. It continues to use the same IP address but does not renew the lease. If I reboot the access point, it will renew the lease again.Is this a known issue with the WAP4410N? Is there any way to work around this, other than setting a static IP address or rebooting regularly?
View 9 Replies View RelatedI randomly lost Internet connection, and since have not been able to Renew an IP address! Other people in my household can connect just fine. I've tried numerous things to get my internet back, but continue to be unsuccessful in doing so.
Microsoft Windows XP [Version 5.1.2600]
(C) Copyright 1985-2001 Microsoft Corp.
C:Documents and SettingsMike>ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : miker
Primary Dns Suffix . . . . . . . :
[code]....
I have an RVS4000 located at my office. A user of mine also has one at their house. We have created an IPSec Tunnel between the 2 of them and have them successfully communicating between the 2 networks with no problem.
The problem I have is if I make a change on their end and the router needs to reboot to apply the changes, the WAN port never renews it's DHCP address. The end user must unplug the unit, plug it back in and then the system comes back up with the correct WAN DHCP address, and the tunnel is connected automatically.
I beleive they have the newest firmware (2.0.0.3) but I cannot confirm that right now as the unit is down. I bought the 2 of them at the same time - my unit at the office has the 2.0.0.3 firmware so I am assuming the users does as well.
I have two Cisco RV220W routers and I would like to realy DHCP from the home office to the remote office accross the IPsec Tunnel. Is this possible and if so how?
I have already gone into the IPv4 LAN (Local Network) settings on the remote router and set the DHCP mode to "DHCP Relay" providing the internal ip address of the home office router as the remote DHCP server.
I've got a WRVS4400N wireless router running DHCP for a couple dozen wireless clients in a public library. We need to gather statistics on the wireless clients on a daily basis: average number of clients, max number of clients, average time used per client etc.
The router only gives a list of clients currently allocated an IP address, but there doesn't seem to be a way to gather statistics over time. Is there a program that will interface with the router to gather more detailed statistics?
I have a (single) client (it is a cisco IOS router) behind a wireless workgroup bridge (cisco1242).The client's IP address is obtained via DHCP from the wired network.Now, when roaming occurs, the Client will never have knowledge about this event,and hence will not renew its IP address until lease expiers. This is not a problem of course when Layer 2 roam occurs, but with Layer 3
roam it will interrupt the traffic.
The cisco's IP Mobile implementation does have this issue addressed in DCCoA scenario: the WGB is configured to send an SNMP trap on its dotradio state change;the cisco mobile router is configured with snmp-server manager to process this trap and start DHCP renew on the Down/Up event. Unfortunately, this works in Mobile IP scenario only because I cannot make it work without the mobile router registered with a home agent.
how to force DHCP renew on a client (cisco IOS router) in such a situation - event scripting, SLA, or ...?
DHCP scope is configured on a WLC 5508.I'm checking if there' a way for WLC to clear the dhcp leasing when a user is diconnected from wireless?
View 2 Replies View RelatedI have a Wireless N router model F5D8236-4 v2 (01) with firmware 2.00.04 (Nov 12 2008 10:51:08) and it's not showing all issued wireless or Wired IP addresses in DHCP Client List.
They all have IP addresses and connect to the internet through the router, but in the router administration page, they're not listing. The Windows devices all show but most of the Mac devices are not, nor is my XBox 360.
My reason for investigating this is because the router seems to keep losing the Mac devices and a router reboot fixes it, but it shouldn't have this problem because all the Windows devices just seem to work.
According to the support page I have the latest available (dated November 12, 2008 which really seems kinda old to me for a Wireless N router). Are there any plans for a new firmware offering for this modem or have you already deprecated it as "legacy equipment"?
Is it possible to use this feature on WLC 2504 ? ( Passive client feature). I found just this note :" The passive client feature is supported on Cisco 5500 and Cisco 2100 Series Controllers. "
View 8 Replies View RelatedDo the problem caused by the modems itself or it just sign of faulty Ethernet switch (using 20 port Allied Telesis ethernet switch).
Sometimes I cannot connect to internet due to "unidentified network" buy i can resolve this problem by restarting my modem + switch.