Cisco Routers :: RV220W - Network Security Firewall / NAT And DHCP
Jun 4, 2013
We have
1-A wireless link (pre-wimax) that provide me with 2 Mb internet connection (tagged Ethernet frames) throught RJ-45
2-have 6 real IP _one of them as Gateway
What i need now is what is the best and cheapest device to do NAT and DHCP to allow users to access the internet , i am trying to do this using Cisco AP 1141 and the link is working fine with static ip configuration on my lap (give my wireless NIC real IP) but now i just need device to do NAT and DHCP
My suggestion is can i use Cisco RV220W Wireless-N Network Security Firewall to do this function. is the WAN port on this router support tagged Ethernet frames ??? or even untagged frames and can i give this router one of those public IPs and give the rest of those IPs statically to other devices on the network.
View 4 Replies
ADVERTISEMENT
Aug 3, 2012
We have installed a cisco rv220w for a client that use to have a simple linksys router and are having some difficulties configuring it. Here is what we are trying to accomplish:
1) we are trying to see cameras at an office using the iphone.
2) with the linksys we would point the iphone app to the manufacturers dynamic dns account that was tracking the ip address at the office. In turn, the linksys had 3 ports forwarded to the camera controller. All was great.
3) we then installed a cisco rv220w and what happens is when the iphone is outside the internal network (on 3G) it works fine. If the owner comes back to the office and connects to the local wifi he can no longer connect to the camera controller. If he types in the local ip address of the controller it works fine but we can't seem to go out of the internal network, connect to the ddns server, and then come back in. This is only an issue if he has 3G and wifi on in the internal network.
4) if he's on a different wifi network and has 3G on it works just fine.
5) how can i setup the router to allow me to go outside the network and then redirect me back in with both antennas on?
Below are the settings we used.
Linksys:
Forward tcp port 81 to 192.1681.200 (controller)
Forward tcp port 41790 to 192.168.1.200 (controller)
Forward tcp port 1025 to 192.168.1.201 (ip video server)
[Code]....
One last note: we installed cisco AP-541 access points in a cluster. No settings were modified on the access points and i think they worked fine with the linksys installed but will have to check.
View 6 Replies
View Related
Jan 2, 2013
I have a Cisco RV220W router (firmware version 1.0.4.17).
I would like to have two separate networks with the following specifications:
Netwrork1: address range for the network is 192.168.0.1-254. All devices should be able to reach eachother within this network and connect to the internet either on LAN or through Wifi. From this network I should also be able to reach the device management page of the router. Also the devices should get the ip addresses throgh DHCP.
Network2: address range for the network is 192.168.5.1-254. All devices within this network should not be able to reach the devices in network1. All devices on this network should reach the internet through Wifi only. Device management page should not be available on this network.
I have configured the router as shown in the attached screenshots but the problem is that in Network2, devices get IPs from the 192.168.0.1-254 range and not from the 192.168.5.1-254 range. Also there is no internet on these either.
View 8 Replies
View Related
Jun 23, 2011
My ISP waits a definite host name from me to return my white IP address via DHCP. Can I set this parameter in RV220W router? I don't find such parameter in IPv4 WAN configuration page.
View 1 Replies
View Related
Oct 9, 2012
I have a Cisco RV220W running the latest firmware (currently 1.0.4.17), and I have noticed that after about a week of use, wireless clients can no longer acquire IP addresses via DHCP.
I have used Network Monitor on both the DHCP server, and the WiFi client, and can see that the server is receiving the requests and sending a reply, but the client never sees the response from the server. So far the only way to resolve this is to reboot the router.
View 10 Replies
View Related
Nov 19, 2011
We assign (reserve by MAC actually) static IPs to all of our devices. Over time we have gotten rid of some devices but haven't begun (or finished really) re-using the old IPs. On our WRVS4400N v2 routers we are able to set the max number of DHCP users per Vlan. This prevents unauthorized devices trying to connect to our LAN.For example. I set the range from 192.168.1.100 - 192.168.1.103. IPs 100, 101, and 103 are in use (reserved via MAC address). We set max number of DHCP users to 3. This prevents someone from gaining access to 192.168.1.102. Does this make sense? Or at least this was the initial goal and it tested out successfully back when we implemented it.
How can I do the same for with the RV220W? I can set the range, assign static IPs (reserve IPs by MAC address), but can't keep others from gaining accessing to our LAN via the unused IPs (not assigned a static IP).My initial thought was to create static IPs (for the unused IPs) using dummy MAC addresses. I'm sure there is a much better way of accomplishing what I am trying to do.
View 3 Replies
View Related
Apr 13, 2012
I have a Cisco rv220w. I just tried updating the firmware. I used RV220W-Firmware-1.0.3.5.img. It rebooted, and now there is no DHCP and no access to anything. I tried the reset button for 10 seconds. That didn't do anything. The WAN and all the LAN lights light up. Power is on and solid. The light blinks alternating between the DMZ and the blank space to the right of wireless. How can I get this back to factory defaults?
View 5 Replies
View Related
Oct 19, 2011
Can add feature "release" and "renew" to wan dhcp client? Is it WOL not possible in RV220w? i tried forward broadcast magic packet from wan side, change broadcast IP and through VPN tunnel (PPTP & IPSEC)...got failed i change from draytek 2130n to rv220w, 2130n much better. except SSL VPN.
View 2 Replies
View Related
Sep 17, 2012
I have an out of the box configured RV220W and was wondering if it supports local DNS resoltuion for DHCP addresses it issues. I have a few reservations and a custon search domain configured ('local') but it will not resolve a name fromt the terminal using the search domain (see below):
It resolves freenas but not freenas.local.
macbookair:~ brantwinter$ dig freenas
; <<>> DiG 9.8.1-P1 <<>> freenas
;; global options: +cmd
[Code]...
View 3 Replies
View Related
Mar 28, 2012
I was trying to set a DHCP pool with 127.16.0.0/16 with RV220W, however, RV220W UI can't save it. It displays "IP Address Range -"Step to reproduce: (it is 100% reproducible)
1. login into RV220W admin web
2. Create a VLAN, id 201
3. Go to "Multiple VLAN subnets", select the VLAN, click edit
4. Enter following info:
IP Address: 172.16.0.1
Subnet Mask: 255.255.0.0
DHCP Mode: DHCP Server
Domain Name: Cisco
Starting IP Address: 172.16.2.100
Ending IP Address: 172.16.10.254
Primary DNS Server: 172.16.0.1
Leave rest of settings with default value.
DNS proxy is enabled
5. Press Save button. The UI shows text "IP Address Range -".
Expected result: RV220W shall save the setting and make use of 172.16.0.0 subnet in IP pool. By the way, the error message "IP Address Range -" seems incompleteI tried same setting on netgear FVS318N (very similar settings to RV220W), it accepts 172.16.0.0/16 as DHCP IP pool and works.RV220W has great feature set meets my needs. Its UI is slow and sometime dashboard freezes, which I can live with comparing to features. But DHCP server IP pool can't be class B is huge limitation to me.
View 1 Replies
View Related
Dec 23, 2011
I have two Cisco RV220W routers and I would like to realy DHCP from the home office to the remote office accross the IPsec Tunnel. Is this possible and if so how?
I have already gone into the IPv4 LAN (Local Network) settings on the remote router and set the DHCP mode to "DHCP Relay" providing the internal ip address of the home office router as the remote DHCP server.
View 1 Replies
View Related
Jan 19, 2012
At this moment (firmware 1.0.3.5) the router has no IPv6 firewall and therefore when used in a typical dual stack IPv4/IPv6 network it has no protection regarding IPv6 traffic. Hopefully this will be fixed with a firmware update before the World IPv6 Day on the 6th of June 2012.
View 1 Replies
View Related
Aug 27, 2012
I would like to isolate my wlan from the remaining network but with two exceptions. First it sould be possible to print from all devices in the wlan and second... my notebook should not be isolated
Therefore I did the followning steps:
1. Create vlan
2.Set access rules
Basically I blocked any inter-vlan-routing from the wireless vlan. I allowed all traffic from the wireless address range to the printer's ip address. I allowed all traffic from the notebook's ip address to the private vlan.
3. Set a static DHCP entry for the notebook
4. Set an IP/MAC binding entry for the notebook
For some reason I can reach any ip address from any wireless device.
View 3 Replies
View Related
Mar 11, 2012
I face a strange bahavior with my rv220w router : I set up access rules to deny all outbound trafic for a particular IP range. It seems to work fine .... but when I enable content filtering, HTTP access on port 80 works again (and other ports are denied). It seems that activating content filtering makes the router ignore firewall rule.
View 2 Replies
View Related
Apr 3, 2012
I do not have a valid SSL Certificate on my firewall but I want to use SSLVPN.
If I connect to the IP adress and the SSLVPN Portal I can choose the sslclient launcher but after that I get a error that I need a internet explorer 64bit or that the active I was blocked because of a unsecure publisher.
View 1 Replies
View Related
Dec 24, 2012
I just got a cisco RV220W and I try to connect it on my wireless network as client, but it doesn't work.
View 1 Replies
View Related
Aug 24, 2011
I am using the RV220W with the latest firmware, I disabled all the four APs and also disabled the Radio, but the "Wireless" green light on the front panel still ON, why? How can I completely turn off the wireless?
Quoted from manual: WIRELESS—The Wireless light is green when the wireless module is enabled. The light is off when the wireless module is disabled.
Moreover I tried to disable the "Radio" while enabled one AP, I found that I can still connect to that AP, so what is the Radio's Enable/Disable used for?
View 16 Replies
View Related
Jan 10, 2013
We have RV220W at corporate office...intent is to have (5) groups of (3) users each connecting via VPN. Had assumed would be using QuickVPN and have set up users, etc and connections at current locations are quick, smooth, reliable. I have set up (2) locations (6 users so far). However, after 4th connection (no matter where or in what order) client hangs at "Verifying Network" and doesn't complete connection. So, I have unique usernames, etc but each of the (3) at a location are hitting the router with the same IP. Is this the problem? I'm sure the RV220W can handle 15 simultaneous connections, but can the router deal with (3) connections from the same external IP?
View 3 Replies
View Related
Sep 22, 2011
Recently i had suffering with wireless connection problem, currently my wireless router connected to WAN directly, after that go into firewall and then go thru switch to end user PC, for LAN user there is no issue, but for wireless connected PC it is prompted with limited connectivity problem(DHCP is disable on router), after check with ipconfig /all. it seem likely due to wireless PC cannot get the IP from DHCP server. i am using DLink615 router. i had checked firewall setting there is firewall policy that connected all router ip into company LAN, but i don't think there is DHCP VPN setting up. is there anyway i can go thru firewall and get IP from DHCP server because if i set up DHCP on router, it cannot pass thru and access to LAN.
View 9 Replies
View Related
Jan 13, 2012
i have a cascading network in my house of 2 linksys routers, I left the DHCP server activated on both of them and it seems to work fine, whats the point of turning it off?
View 2 Replies
View Related
Jun 13, 2012
I have an inside network using PAT to one outside address. Our DNS server is on another local, but outside address. I can't get the inside network to successfully get addresses.I have another inside address that just uses the wirewall and gets addresses just fine from the same server.I have the box checked in ASDN that enables DHCP on the inside interface and points to the correct DHCP server,PAT service is working properly if I use a hard coded address for a machine on the inside network.This is an ASA5540 with 8.3(2)
View 2 Replies
View Related
Aug 14, 2012
I am having a very strange issue with connecting new machines to reach the internet.We have a ASA 5505 which the previous tech configured the DHCP pool to 192.168.1.60 - 192.168.1.110
We ended up reaching our limit which I changed it to: 192.168.1.60 - 192.168.187
Then next day when I arrived to work, our DC was hung from windows updates. Once we got everything back up, every computer currently on the network can reach the internet/VPN tunnels etc. So (continuing with my day) I created a new server in a VM (Hyper-V)I can ping everything internally (even the router) 192.168.1.1, but I cannot resolve DNS. I have configured a static IP, tried Dynamic IP.I have looked for any ACL indicating to block outside the range of the old DHCP pool but no luck.On my local maching I can ping the DNS addresses, but just not on the new server.
View 1 Replies
View Related
Jan 12, 2012
How do I find my network security key for my cisco e1000 router if the computer that it is installed on is broken?
View 1 Replies
View Related
Apr 2, 2012
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies
View Related
Aug 24, 2012
I am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies
View Related
Jul 3, 2012
Picked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
View 9 Replies
View Related
May 15, 2012
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
View 5 Replies
View Related
Dec 12, 2012
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
View 8 Replies
View Related
Sep 28, 2011
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies
View Related
Nov 27, 2011
Is there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies
View Related
Jul 22, 2011
i have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies
View Related
Jul 19, 2012
I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies
View Related
Jun 23, 2012
Having a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies
View Related
