Figure Out Primary And Secondary DNS?
Jun 22, 2011How can you figure out your primary and secondary DNS? I have a linksys router, and i'm trying to figure out what my primary and secondary DNS are so i can hook up my PS3 online.
View 1 Replies
ADVERTISEMENT
Make Secondary Router As Primary?
Apr 25, 2011I have been having problems when trying to host servers on games, etc.I have 2 routers. A modem router, which is a Thomson router. That is the main one. It has a wire connecting from it, to a D-Link router that is near my Computer, and my brother's one. Then that D-Link router has 2 wires from each port, to mine, and my brother's computer.So, I am trying to host games.I didn't connect to the Thomson one, which is also wireless. I am connected to the wired one (D-Link). When I try to host while connected to it, my brother, and other people can't find the server. My brother and me can find it on LAN, but not Internet.But when I disconnect from the Wired, and connect to the Thomson wireless one, and then when I host, I can find it on INTERNET. Even my brother can. He can connect to it perfectly.
I do not want to connect to the wireless, because then it will cause lag spikes every 5 minutes.So, when I disconnect from the wireless, and connect to the wire, I went into the CMD, and typed in ipconfig. I found out that the Default Gteway is the D-Link IP.When I connect to the wireless, and disconnect the wired, I went into CMD, and then the Default Gateway is the Thomson one, which is the main router.So what I want to do, is use the D-Link router, and that router will have the same IP as my thomson one, so that I can host perfectly with no lag spikes, and using a wired connection.
Cisco AAA/Identity/Nac :: ACS 5.3 Primary / Secondary Same License?
Jan 22, 2012I have a question about the number of Cisco licenses needed in two cases for ACS 5.3 Virtual Machine.One primary + One secondary : Just one license for all or one license for the primary + another one for the secondary ?One primary + several secondaries : Just one license for all or one license for the primary + just one license for all the secondaries ?
View 1 Replies View RelatedSingle SSID For Primary And Secondary DD-WRT Wireless Router
Feb 22, 2013I have more than 5000 sq. ft home and have some dead places other end of the house. Now I am looking for Range Extender/Repeater to boost signal. My primary wireless router is Motorola Surfboard SBG6580 and Secondary Linksys E3000 (planning to update firmware to DD-WRT). So I wanted something such that I can roam between the two routers without switching SSID (use single SSID name for primary and secondary DD-WRT routers) and connect automatically to whichever the best signal (or) strength router. In work place we have same thing like that single wireless SSID name which automatically connect wireless SSID from one end to another end of the building.
View 1 Replies View RelatedCisco AAA/Identity/Nac :: Use Two Servers ACS 5.2 In (primary And Secondary) Active?
Jun 16, 2011it is possible de use two servers ACS 5.2 (primary and secondary) in active/ active? or just in active/ passive?
View 3 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.3 - Unable To Re-register Secondary To Primary?
Jun 11, 2012Today I ran a failover test between our primary and secondary ACS systems (ran 'acs stop' on the primary) and in the process decided to promote the secondary while I had the primary down. All was fine until I brought the primary back up and tried to re-register the secondary to it. I get the following error message: I went into System Administration >Operations >Distributed System Management on each and it showed the other device as deregestered, tried to promote from there but it failed too, so I deleted them and tried to register the secondary again. After that didn't work I tried rebooting both but that didn't work either. I know the user/pass I'm using is good and I've tried using both the IP address and the hostname.
ACS/admin# sh app version acs
Cisco ACS VERSION INFORMATION-----------------------------Version : 5.3.0.40.5Internal Build ID : B.839Patches :5-3-0-40-5
Cisco VPN :: 888 Configure VRF With COOP Having Primary And Secondary Key Servers
Jun 19, 2012We are trying to configure vrf aware GET VPN with COOP having primary and secondary key servers and also 3 GM routers. All GM routers we use are Cisco 888 and Key servers we use cisco 2911 routers. All GMs crypto maps have been applied into Vlan interface as there's no L3 interface on 888 routers.
Always members can form a tunnel with primary KS, we have configured redundancy with secondary key server and listed on each GM primary and secondary KS on GDOI group.
The issue we facing is that whenever we shutdown the primary or secondary servers the tunnel is not forming with available KS unless otherwise we mannually clear the crypto session. In another way when primary KS down it doest not fall back to secondary KS and no GM get registered. We have already played with all the timers such as DPD, SA lifetimes, GDOI rekey lifetime etc and also exchanging the keys (import/export) with KS and COOPs but there's no luck. We could see the following message was seen on both KS.
[code] 192.168.1.3 is the primary KS and 192.168.1.6 is the secondary KS.I captured attached debug output from 1 GM and secondary KS while I shutdonw the primary KS and also attached is our senario we were trying get work.
Also attached is the show output from both KSs when it form a tunnel with GM.
Cisco Firewall :: 5505s - Secondary ASA Active And Primary Is On Standby
Dec 5, 2011We have 2 ASA 5505s in a data center at a remote site.
Whilst troubleshooting another issue I noticed the below. I don't know much about fail over but this would suggest that the secondary ASA is active and the primary ASA is on standby.
if the primary is "active" then how come the secondary is the active ASA? I would have thought that once the primary ASA became active this would assume the "main" role".
[Code] .....
Cisco :: Setting Up Primary And Secondary 5508 Using Redundancy Port
May 15, 2013Management purchased a HA package from Cisco consisting of 2 5508's with pre installed 500 users license on the Primary WLC and none on the secondary WLC. We have 5508's already so I am familiar with setting them up and so forth. What I am not familiar with is setting them up using HA for failover and license sharing. I've looked and looked and can't find documentation online showing how to set this up. I have found some but nothing that is complete. I have spent 2 days spinning my wheels.
View 2 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.2 - Primary-secondary Radius Server Configuration
Apr 21, 2013I have a couple of ACS 5.2 configured as active and backup and I am doing dot 1x authentication using these servers . I have configured the switch with the bellow configuration.
radius-server host 10.0.10.15 auth-port 1645 acct-port 1646
radius-server host 10.0.10.16 auth-port 1645 acct-port 1646
radius-server key 7 aaaaaaaaaaaaaa
please help to understand what will happen in switch
1) in case of primary failure
2)in case if primary returns alive .
Cisco AAA/Identity/Nac :: Secondary ACS 5.1 Fails To Deregister After IP Change On Primary
Aug 9, 2011IP address of Primary had to be changed, to respond to a hardware failure of TACACS server with IP in many device configs.
Now the Secondary fails to respond to repeated "Deregister from Primary" requests, even after reload - apparently because it cannot reach the Primary at its old IP address.
Requesting Deregister in GUI generates pop-up that says, "This operation will deregister this ACS Instance from the Primary Instance. Management applications on this ACS instance will be restarted and you will be required to login again. After performing this operation
[code]....
Cisco AAA/Identity/Nac :: ACS 5. 2 Secondary Server Is Not Collecting Logs From Primary
Nov 2, 2011Cisco ACS 5.2 secondary server is configured as a log collector for both primary and secondary server .Now i am facing problem in log collection from primary server .ACS secondary server is not collecting any logs from primary .
View 2 Replies View RelatedCisco VPN :: 5520 - Primary And Secondary ASAs / L2L Tunnels Not Responding?
Apr 12, 2011I have a pair of ASA5520s in active/active failover - this works fine. Both primary and secondary ASAs are running 8.2(2) code.I have a 30-day temp 50 seat SSL license that I applied to the primary. I then started having problems with L2L tunnels.
I noted that if the 'show crypto isakmp sa' state for an L2L was MM_STANDBY, then the remote protected net could not reach my side. However, I could ping across to the other side at which time the state changed to MM_ACTIVE as I would expect and the remote could then reach my side.
I believe this results from the differences between the two licenses. When I applied the 50 seat SSL lic. it disabled failover, but I was willing to risk that for a few days to do show my customer the benifits of SSL connectivity. Note license differences. Is this causing the MM_STANDBY IKE issue and if so can I overcome it and use the 50 SSL VPN Peers lic.
[code]...
Cisco Switching/Routing :: C6509 - Broadcast Not Working Between Primary And Secondary IP Address
May 11, 2012I have recently configured secondary ip address on LAN Interface of Cisco C6509.. We have some application which needs to use broadcast traffic communication to communicate with client... Broadcast is working within subnet & also working from broadcast server to primary subnet. But not working from secondary subnet.. I have checked broadcast within secondary IP range & it's working fine... Secondary not working broadcast with primary and also with broadcast server... broadcast address is different for these subnet but both should be communicate since configured on same interface... When I went through Cisco website found that command "ip directed broadcast" which will pass broadcast to different subnet... But I'm not sure whether any other impact if I enable that command on particular Ethernet interface...
View 6 Replies View RelatedCisco Firewall :: ASA 5505 - Dual ISP SLA Track With Primary PPOE Secondary DHCP
Aug 25, 2011Cisco ASA 5505 Security Plus 1 link with PPOE dialup for internet access
desirable situation: Primary link with a PPOE dialup Secondary Link with DHCP address Asignment
Problem: i want to configure Dual ISP Failover modus, but the problem exist when i configure the ip sla syntax it looks good in the running config. but after a reload the secondary line becomes primary
It looks like the ppoe client authentication is busy when the ip sla tracking mechanism becomes active. can i tweak the settings that the ip sla tracking mechanism starts later?
What i the correct config for Dual ISP setup with primary PPOE and secondary DHCP
Cisco Switching/Routing :: 887m - Unable To Route Data Between Primary And Secondary IP Networks
Jan 7, 2013We an 887m router in our office with an unmanaged switch. We have two networks, 192.168.0.x and 192.168.11.x connected to router on the same interface (192.168.11.253 is a secondary ip) but I can seem to be able to route packets from one network to the other. Internet traffic is fine from both networks. I can't see what I'm doing wrong here. I can ping the 192.168.11.253 (router) from the 192.168.0 network but nothing beyond that.
I tried this at home with no other config and its the same. Is this by design?
Cisco :: Failover Configuration - Allow Primary Link To Fail And Secondary Link To Automatically Pick Up Traffic?
Dec 27, 2012We have a customer who has a network consisting of two ISPs, one as a primary and the other as a backup. We are trying to create a configuration that would allow the primary link to fail and the secondary link to automatically pick up traffic and begin routing .how to set something like this up. Both routers are non Cisco routers and there for HSRP is out.
View 14 Replies View RelatedHow To Figure Out Password To Network
Feb 4, 2012i cant get the security code or password for my router
View 1 Replies View RelatedLaptop Won't Figure Out Network - Undefined
May 27, 2011My laptop will either connect somedays or won't connect at all!!!! Sometimes it will connect but wont figure out my network call it "Undefined" and makes it a public access and then its super slow.....even though its MY secured wireless! Its a Linksys N router and it worker great when we had At&T, but since we moved we could only get stupid Comcast.... My sister's Ipod Touch connects fine so what gives??? I've tried power cycling, and pulling up my router's page and followed instructions with MAC addresses and all that stuff. Its working now (after restarting my lap top twice-removing the network from my list and re-connecting to put in the password and then restarting) but who knows for how long!
View 1 Replies View RelatedCisco :: ACS 5.1 Promote Secondary Server
Mar 2, 2011In ACS 5.1 how do I promote the secondary server to local mode if I have lost the primary server, in this scenario is it only accessible by the CLI and would you have to manually promote it so as to enable further configuration elements via the GUI? I would have thought that if the primary failed some sort of keep alive from the primary to the secondary would be lost thus making the secondary force it's own promotion but this does not seem to be the case???
View 2 Replies View RelatedCisco AAA/Identity/Nac :: ACS V.5 Cannot Be Added As Secondary Via WAN
Aug 26, 2012i have planned a deployment with one acs in Europe working as primary, one acs in europe as secondary and one acs in USA as secondary also.
I can add one acs in europe to the deployment as secondary. When I try to add the acs in USA to the deployment - Nothing really works.
The status shown in the primary is offline (red) and status pending. It stays like this for hours. When I log in to the gui directly on the acs in USA, it still has status primary.
The two acs are transparently connected. There is WAN optimization (cisco waas) in between the two datacentres..
Cisco AAA/Identity/Nac :: Can't See Login Secondary ACS 5.2
Apr 24, 2011I have two ACS 5.2 working in redundancy Primary and Secondary my question in when my primary ACS goes down i can´t see the log in the secondary ACS. I read in the documentación that only one ACS can be configurated for working like logg collector server. Now I configurated my secondary ACS like logg collector server now when my Primary ACS goes down i can see the logg. Finally when my Secondary ACS goes down i can modified the ACS Primary Configution by show me the logg.. Is possible to do this automaticaly for show me the event logg ? when the ACS that is configurate like logg collector server goes down pass the event other ACS automatically..
View 3 Replies View RelatedCisco WAN :: 2821 NAT Secondary Public IP
Sep 12, 2011I have 1 2821 router with several IP addresses from a single provider. The IP addresses are not contiguous.I would like to NAT different internal subnets to different external IP's. i.e. map 10.1.1.0 to x.x.220.68 and 10.1.2.0 to x.x.220.70 and 10.1.3.0 to x.x.105.184.
I currently have ip nat inside source route-map SDM_RMAP_1 interface GigabitEthernet0/1 overload that translates everything to x.x.105.184.What would be the best way to setup the NAT statements to be able to divide up the subnets?
Cisco WAN :: 2821 / Using Secondary IP Address For NAT?
Mar 16, 2012On a cisco 2821 running 15.1(3)T1 From this cisco DOC, common use of secondary IP addresses on an interface are
•There might not be enough host addresses for a particular network segment. For example, suppose your subnetting allows up to 254 hosts per logical subnet, but on one physical subnet you must have 300 host addresses. Using secondary IP addresses on the routers or access servers allows you to have two logical subnets using one physical subnet.
•Many older networks were built using Level 2 bridges, and were not subnetted. The judicious use of secondary addresses can aid in the transition to a subnetted, router-based network. Routers on an older, bridged segment can easily be made aware that many subnets are on that segment.
•Two subnets of a single network might otherwise be separated by another network. You can create a single network from subnets that are physically separated by another network by using a secondary address. In these instances, the first network is extended, or layered on top of the second network. Note that a subnet cannot appear on more than one active interface of the router at a time.
On the WAN interface I've added two Secondary Public IP's (from the same subnet) to use for NAT to internal hosts. Is this a common scenario or is there a more typical way to acheive this. This assumes, I do not want to put a Public IP on an interface on the internal server.
interface GigabitEthernet0/1
description WAN$ETH-WAN$
ip address x.x.x.1 255.255.255.240
ip address x.x.x.2 255.255.255.240 secondary
ip address x.x.x.3 255.255.255.240 secondary
[code]....
AAA/Identity/Nac :: 1121 - Add Secondary ACS Server 5.4?
May 29, 2013My customer has an ACS 1121 version 5.4. Now we want to install a secondary ACS 1121.
View 2 Replies View RelatedCabling / Cards :: Secondary PC Does Not Recognize USB Devices
Dec 25, 2011My secondary PC does not work with the Wireless US adapter or any other USB device that I insert in the USB ports. What do I need to download to get this PC to work in my (home) network
View 1 Replies View RelatedBackup Internet Access Through Secondary Router?
Jan 30, 2013I have two routers on my local network:
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled)
2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2
There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the same subnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it possible by configuring the DHCP server to assign the primary DNS address as 192.168.1.1 and secondary DNS address as 192.168.1.2?
Linksys Cable / DSL :: WAG54G-EU Secondary IP Setting
Mar 21, 2011Can I add a secondary IP address for LAN interface to manage two LAN in my network?
View 1 Replies View RelatedD-Link DIR-655 :: Configuring It As Secondary Access Point?
Sep 15, 2009I have a DLG-4500 router as my primary router and want to connect a second router (DIR-655) to it as an extention of the LAN to the second floor of my home. I have found instructions on doing this with most other routers, but not DLINK. In fact when doing the initial configuration and trying to disable the WAN link on the second router by using a bogus IP address string (127.0.0.1) The router won't let me save the change? What are the steps for configuring a secondary router cascaded to the primary (both wireless) to extend network coverage.
View 13 Replies View RelatedCisco Firewall :: Secondary IP Address In ASA5510
Feb 7, 2013Just want to know if there is a way to configure secondary IP address on the outside/public interface of ASA/PIX.One of our clients have used most of their IP on the subnet given by their ISP. They use those IP's for staticallymapping to Servers inside their local LAN. Thus, they requested another block/subnet from their ISP. They will also use this for static mapping/port forwarding to other servers in their network. The current UTM they are using is allowing this but they would like to use ASA/PIX as their main Firewall. Is this even possible or is there a workaround for this kind of scenario?
View 5 Replies View RelatedCisco VPN :: 871 - Backup GRE Tunnel Using Secondary IP Address
Oct 3, 2011Is it possible to setup a Backup GRE Tunnel using a Seconadary IP Address on the WAN interface. The router is a Cisco 871.
View 33 Replies View RelatedCisco AAA/Identity/Nac :: ACS 5.3 How To Enable Log On Secondary Server
Feb 28, 2013We are using ACS 5.3 with two servers in a distributed solution.All logs are collected on primary server so when this server fails all logs are lost.How can I enable log on secondary server also?
View 2 Replies View RelatedCisco Firewall :: Secondary IP Over 5505 Fastethernet
Jun 13, 2012I would like to know if is possible to configure a secondary IP address in a 5505 interface ??
View 1 Replies View Related