Cisco Firewall :: Secondary IP Over 5505 Fastethernet
Jun 13, 2012I would like to know if is possible to configure a secondary IP address in a 5505 interface ??
View 1 Replies
ADVERTISEMENT
Cisco Firewall :: ASA 5505 Cannot Ping Secondary Internal Network?
Jan 15, 2012Cisco ASA 5505 Cannot Ping Secondary Internal Network.
View 9 Replies View RelatedCisco Firewall :: ASA 5505 - Dual ISP SLA Track With Primary PPOE Secondary DHCP
Aug 25, 2011Cisco ASA 5505 Security Plus 1 link with PPOE dialup for internet access
desirable situation: Primary link with a PPOE dialup Secondary Link with DHCP address Asignment
Problem: i want to configure Dual ISP Failover modus, but the problem exist when i configure the ip sla syntax it looks good in the running config. but after a reload the secondary line becomes primary
It looks like the ppoe client authentication is busy when the ip sla tracking mechanism becomes active. can i tweak the settings that the ip sla tracking mechanism starts later?
What i the correct config for Dual ISP setup with primary PPOE and secondary DHCP
Cisco Firewall :: ASA5510 Secondary Firewall Crashes After Upgrade To 8.4.1
Jun 29, 2011I have two ASA5510's set up in failover, and the secondary keeps crashing after doing the interface checks when bringing failover up. This only happens if I try to upgrade the image on the secondary to anything newer than 8.4.1 (I've tried with 8.4.1-11 and 8.4.2). The primary one run just fine with new images.
I don't have the exact error right now, as I need to do a screen capture from console. It's just a huge crash dump.Are there anything I might have missed during the upgrade? Should I cold-boot both the firewalls in the correct order?
Cisco Firewall :: Secondary ASA 5550 Firewall Getting Down Automatically?
Apr 17, 2011I am having two ASA 5550 firewall running in active/standby mode. With in last two months our secondary firewall got down automatically 3 times. Firewall is running with IOS version 7.1.2. how to proceed further troubleshooting because there are not any logs on firewall.
View 3 Replies View RelatedCisco Firewall :: Asa5510 - How To Add Secondary Firewall
May 4, 2012I have a cisco asa 5510 with security plus license in Live enviroment . I need to add a secondary firewall . I was planning to do in active /standby mode for failover .But i have a doubt , when i do "show version " on live asa output says Active /active failover , does this means that i can only configure failover in active/active mode not in active/standby (which i want to do )?
Maximum Physical Interfaces : 8
VLANs : 20, DMZ Unrestricted
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 25
WebVPN Peers : 2
Dual ISPs : Enabled
VLAN Trunk Ports : 8
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5505 Security Plus license...
Cisco Firewall :: Secondary IP Address In ASA5510
Feb 7, 2013Just want to know if there is a way to configure secondary IP address on the outside/public interface of ASA/PIX.One of our clients have used most of their IP on the subnet given by their ISP. They use those IP's for staticallymapping to Servers inside their local LAN. Thus, they requested another block/subnet from their ISP. They will also use this for static mapping/port forwarding to other servers in their network. The current UTM they are using is allowing this but they would like to use ASA/PIX as their main Firewall. Is this even possible or is there a workaround for this kind of scenario?
View 5 Replies View RelatedCisco Firewall :: Implement Secondary ISP To ASA 5510?
Aug 27, 2012We are in the process of implementing secondary ISP to our ASA firewall and We would like to run both ISPs in parallel so we can test until we finally cutover?
View 2 Replies View RelatedCisco Firewall :: Assign Secondary ISP-2 Pool IP To DMZ Server?
May 15, 2011Can we assign Secondary ISP-2 Pool IP to DMZ Server, network design attached for reference.
View 2 Replies View RelatedCisco Firewall :: ASA 5520s Secondary FW Sub-Interface Failure
Mar 3, 2013I have two ASA 5520s in Active/Standby. I try and test this quartely to ensure it is working correctly. Everything works fine, except I have an issue with one interface. When doing a show failover, it shows the interface as failed on the secondary unit, and I am not sure why. It shows it as normal on the primary.
This host: Primary - Active
Active time: 9277305 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(4)) status (Up Sys)
Interface WaterworksCanopy (192.x.x.x): Normal
[code]....
Cisco Firewall :: 5505s - Secondary ASA Active And Primary Is On Standby
Dec 5, 2011We have 2 ASA 5505s in a data center at a remote site.
Whilst troubleshooting another issue I noticed the below. I don't know much about fail over but this would suggest that the secondary ASA is active and the primary ASA is on standby.
if the primary is "active" then how come the secondary is the active ASA? I would have thought that once the primary ASA became active this would assume the "main" role".
[Code] .....
Cisco Firewall :: Configure Secondary IP On Inside Interface Of ASA 5520?
Nov 24, 2012We already have a subnet defined to inside interface and is in produciton. the default gateway is this interface ip. In that setup now I have to add one more subnet and as the first subnet is been defined in ASA indside interface, I have to assign secondary Ip to the inside interface so that new subnet users can easily reach here and go outside.
View 1 Replies View RelatedCisco Firewall :: ASA5505 Alias Secondary Subnet / No Communication Between Them?
Aug 17, 2011As this is an ASA 5505, unlimited users, I must use arp alias to allow a secondary network.
Inside network: 10.200.31.0/24.Additional inside network: 10.200.12.0/24
Clients in both networks can reach internet, but they can't communicate with eachother. Hosts on the additional network can ping the ASA inside network IP, but nothing else. I get incomming hitcount for inside interface when 10.200.12.x tries to ping 10.200.31.x. In the error log, I see: [code]
Cisco Firewall :: Integrating Secondary Failover Unit ASA 5510?
Nov 20, 2011I have a single production 5510 with 2 contexts. Now I want to integrate the secondary failover unit. My question is: How much configuration needs to be done on the secondary firewall? How much of the configuration will be sync'd from the primary to the secondary when the secondary is connected?
For example, do I need to add the following on the secondary or will it be sync'd from the primary?
admin-context NAME
context NAME
allocate-interface Ethernet0/0.14
[Code].....
Cisco Firewall :: Can ASA 5555 Translate To Secondary IP Address Block
Oct 14, 2012I just purchased an ASA 5555 and started to configure. I was successful in natting all the IPs that are on the same subnet as the ASA eth0. I could not get the nat working for the 2nd address block.
Ex:
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 192.168.1.33 255.255.255.224
[Code]....
Cisco Firewall :: Secondary ASA5525 Interface Flap When Write Standby
May 23, 2013i never see this before, but on newly purchased just configured firewall.when i do wrtie standby.All interfaces on standby unit flaps.is it some IOS bug? my firewalls are [code] what could be the reason? FYI i am using LAN base failover and not doing any statful fail-over.
View 3 Replies View RelatedCisco Firewall :: ASA 5520 - Stand Up Secondary DMVPN Hub At Recovery Site?
Nov 8, 2012I have a working DMVPN solution. I am trying to stand up a secondary DMVPN hub at our disaster recovery site. We are trying to deply to a Dual HUB SIngle DMVPN solution. The HUB2 DMVPN router has an INSIDE trusted interface and has an OUTSIDE UNTRUSTED interface.
The inside is 10.248.11.X...the Untrust/public is 192.168.93.11 which is connected to our DMZ 3 on the ASA 5520.....then I am trying to NAT the 192.168.93.11 to an outside public IP 199.248.30.X....just not working...have had 2 tickets open with Cisco this week and they still are unable to resolve. I am sure it is the ASA5520 is not configured correctly.
Cisco Firewall :: 5520 - Procedure To Replace Failed Secondary ASA Unit
Apr 10, 2012i just received a RMA for failed ASA 5520 that was acting as secondary unit in multicontext configuration. What would be correct procedure to install it back in production? Do i need to restore backed up config of the fallen unit or is it just enough to enable multimode and connect to existing (primary) unit? Any good link for documentation that deal with this issues.
View 5 Replies View RelatedCisco Firewall :: 3845 - Open Port Range On Secondary IPs On Router Interface
Feb 12, 2013 I have 4 public IPs on Router 3845 interface FastEthernet 0/0/1. IP as below.
50.200.2.2
50.200.2.3 secondary
50.200.2.4 secondary
50.200.2.5 secondary
I wan to allow ports 80 to 90 on 50.200.2.3 for my webserver (192.168.10.50)
Cisco WAN :: Fastethernet Module For 7204 VXR?
Dec 19, 2011We have a cisco 7204 VXR and would like to know the module which has two fastethernet port. We tried a PA-2FEISL-TX but it did not work.
View 1 Replies View RelatedCisco WAN :: 1841 With Two FastEthernet Ports
Mar 26, 2013I am having the most difficult time trying to setup the Cisco 1841 with a new Fiber Optic ISP. I have no experience with Cisco equipment but have taught myself some basics. All my attempts have ended with failure. I definitely will be taking some cisco courses soon.
Our current setup
20mbs Fiber Optic ISP
- They are providing us a x.x.129.233/30 WAN IP and a x.x.131.225/27 Public IP Block Cisco 1841 Router (Which has no configuration at all, it was wiped by the ISP) 1x HP Procruve 2610 24 port Gigabit Switch
What we need is simple, we just need to distribute the Public IP block through to the LAN on the switch side. I would post a config if I had one already made, but the 1841 is a clean slate. I just wiped it again to start fresh.
Cisco WAN :: 819 Cellular Interface Drops When FastEthernet Comes Up
Apr 25, 2013We're seeing a strange issue with a Cisco 819 that we're testing out. We are able to ping out over the Cellular interface just fine, but as soon as we plug a device into one of the FastEthernet ports we immediately drop the cell connection. The Cell interface then continues to bounce until we unplug the device. We are intending to setup a VPN tunnel, but we've even stripped all that out for the sake of troubleshooting.
Current configuration : 2832 bytes
!
version 15.2
[Code].....
Cisco Wireless :: Connecting 2504 WLC To Fastethernet Port?
Jun 5, 2012Is it mandatory to connect Cisco WLC 2504 to a Gigabit port ?? can we connect it to a fasternet port (100 mbps) ?
View 4 Replies View RelatedCisco WAN :: SR 520 - Can Layer2 FastEthernet Port Be Upgraded To Layer3
Feb 26, 2012I have a SR520 router with the ADSL WAN built in. I am looking to ignore the ADSL port and utilise the 4 FA ports to route between two networks.Can I configure the ports on the switch part of the router to become Layer 3 and take there own Ip addresses? If so I can save myself the purchase of a new router.I have used loopbacks before but not sure that will work.
View 9 Replies View RelatedCisco WAN :: Connect Integrated FastEthernet Ports On 2921/k9 To ISP
Jun 26, 2012I am getting the new Cisco 2921/K9 router, which comes by default with 3 Integrated 10/100/1000 Ethernet ports. I have Comcast Cable as the ISP, so can I connect the ISP RJ45 Copper cable directly to one of the integrated ports or do I have to buy another WAN Interface Cards for the ISP.
View 3 Replies View RelatedCisco WAN :: 1800 Series Router - QoS On FastEthernet Subinterface
Jun 28, 2011We have 2.5 Mbps connection from an ISP at our branch routers (1800 series)with single physical link terminated on FE0 but have two subinterfaces with separate subnets.
I have applied the following policy-map outbount under physical Interface FastEthernet 0. Show poliocymap output is as follows
Policy Map QoS-OUT
Class Email
priority 512 (kbps)
Class SQL
priority 512 (kbps)
Class File-Copy
police cir 1024000 bc 32000
conform-action transmit
exceed-action drop
Class CCTV
police cir 384000 bc 12000
conform-action transmit
exceed-action drop
But it seems that sometimes( not all the time ) the CCTV traffic seems to exceed the 384k and chokes the entire link(2.5 mbps).
Cisco Infrastructure :: NM-1Fe Fastethernet Module Not Compatible With 2 Series Routers600
Oct 13, 2012I understand that the NM-1FE Fastethernet modules are not compatible with Cisco 2600 series routers, just the Ethernet 1-E module. With that being said, are there ANY modules supported by the 2600, 2621 or 2621XM series routers that have fastethernet port(s) outside of the pricey NM-16ESW module? I don't need a 16 port module!
View 3 Replies View RelatedCisco WAN :: Input Errors On Fastethernet Interface Router 2811
Feb 22, 2012I have this output from show interfaces command for the fastethernet interface on a 2811 router.
find the causes of the crc and the ignored input errors on the interface?
The interface configuration is:
interface FastEthernet0/0description VLANS_CHILE
no ip address
[Code]....
Cisco Wireless :: 1300 Series Bridge And FastEthernet Link Status
May 7, 2008I am trying to install a AIR-BR1310G wireless link between two buildings. I configured the setup in a lab and had everything functioning. Shipped it to the client who is now trying to install it. The radio link is up, but we are having issues with the remote Ethernet connection.The root bridge is connected to a WS-C3560G-24TS (core) switch. The port is setup as a trunk with a native vlan of 2 (our management vlan). [code] if I do a "show power-injector" on the remote radio (no Ethernet link), I get: "Received zero AutoMIB packet from Power Injector, Check to see if CDP is disabled on Fast ethernet" repeating. No other entries. If I do the same command on a unit with a link (root bridge) I get information about "Power Injector Port 0 speed 100Mb/s duplex full link up enabled yes" with a bunch of stats. Similar for "Power Injector Port 1". Power Injector Ports 2-4 as "down" and 5-6 as "disabled". Other than the 3 different patch cables they tried (all straight through) or a crossed cable (try tomorrow when they buy one), is there any other reason the port won't go Up/Up?
View 3 Replies View RelatedCisco Switching/Routing :: Bandwidth Limit On 2811 Router Fastethernet Interfaces?
Mar 23, 2013I have a task of setting up bandwidth limit on the 2811 router Fastethernet interfaces.The scenario is:We have a 4MB Internet connection and would like to allocate bandwidth usage to users.
Fastethernet 0/0 needs to be set with 256KB output and 2048 input. This is going to be connected to a wireless router. Fastethernet 0/1 needs to be configured with 2048 output.I could also use SDM if that's easier than using CLI.
Cisco Switching/Routing :: 861 - Can't Configure FastEthernet Ports To Hand Out Address Automatically
May 27, 2012We have upgraded our gateway router from a Cisco Linksys RVL200 to a Cisco 861, this is a big jump from a GUI driven system to IOS CLi and i'm having issue finding my feet. I tried the Cisco CP system but it didn't work so I'm going to configure it with IOS commands. I wish to replicate the current configuration on the 200 with the following setup.
I have created a DHCP pool but i am unable to configure the FastEthernet ports to hand out address automatically, the pool is called USERS with range 192.168.1.30 -> 192.168.1.253.How do I work out the client-identifier for a DHCP client, I don't want to plug this into the network and manual reconnect all the PC's just to get the ID then make a static route.
Cisco Firewall :: Monitoring ASA 5505 Firewall Active / Standby Pair Using SNMP?
Sep 7, 2011How I can actively monitor the interfaces and overall status of 2 x ASA 5500s in an Active/Standby configuration?
I can setup monitoring of the interfaces on the Active member but I'm not sure how to manage the Standby member?
Cisco Firewall :: IOS Firewall Versus ASA (5505 / 5510) For Smaller Clients (less Than 50)?
Apr 24, 2012We were having a discussion of ios firewall vs. asa for smaller clients(less than 50). On using ios firewall(zbf or cbac)and an asa 5505/5510. One of the arguments brought up on using ios firewall on the router is that a router will do an ip sla failover. I have configured a number of isr's for this and i know it works good.
View 1 Replies View Related
