Cisco Firewall :: Asa5510 - How To Add Secondary Firewall
May 4, 2012
I have a cisco asa 5510 with security plus license in Live enviroment . I need to add a secondary firewall . I was planning to do in active /standby mode for failover .But i have a doubt , when i do "show version " on live asa output says Active /active failover , does this means that i can only configure failover in active/active mode not in active/standby (which i want to do )?
Maximum Physical Interfaces : 8
VLANs : 20, DMZ Unrestricted
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 25
WebVPN Peers : 2
Dual ISPs : Enabled
VLAN Trunk Ports : 8
AnyConnect for Mobile : Disabled
AnyConnect for Linksys phone : Disabled
Advanced Endpoint Assessment : Disabled
UC Proxy Sessions : 2
This platform has an ASA 5505 Security Plus license...
View 4 Replies
ADVERTISEMENT
Jun 29, 2011
I have two ASA5510's set up in failover, and the secondary keeps crashing after doing the interface checks when bringing failover up. This only happens if I try to upgrade the image on the secondary to anything newer than 8.4.1 (I've tried with 8.4.1-11 and 8.4.2). The primary one run just fine with new images.
I don't have the exact error right now, as I need to do a screen capture from console. It's just a huge crash dump.Are there anything I might have missed during the upgrade? Should I cold-boot both the firewalls in the correct order?
View 7 Replies
View Related
Feb 7, 2013
Just want to know if there is a way to configure secondary IP address on the outside/public interface of ASA/PIX.One of our clients have used most of their IP on the subnet given by their ISP. They use those IP's for staticallymapping to Servers inside their local LAN. Thus, they requested another block/subnet from their ISP. They will also use this for static mapping/port forwarding to other servers in their network. The current UTM they are using is allowing this but they would like to use ASA/PIX as their main Firewall. Is this even possible or is there a workaround for this kind of scenario?
View 5 Replies
View Related
Apr 17, 2011
I am having two ASA 5550 firewall running in active/standby mode. With in last two months our secondary firewall got down automatically 3 times. Firewall is running with IOS version 7.1.2. how to proceed further troubleshooting because there are not any logs on firewall.
View 3 Replies
View Related
Jun 11, 2012
I am able to ping from Switch to firewall inside ip and user desktop ip but unable to ping from user desktop to FW Inside ip.. config is below for both switch and FW Cisco ASA5510....
TechCore-SW#ping 172.22.15.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.22.15.10, timeout is 2 seconds:
[Code].....
View 7 Replies
View Related
Sep 10, 2012
i have a ASA5510 in the office, that already configured 3 context, namely, admin, user, server.in the server context, the last running config was not saved, and there was a power trip last friday night. 1 of the sub interface was affected, and i need to recreate that interface.I am getting the below error, it only allow me to do changes those pre-defined interface.how to I create extra sub interface?
View 3 Replies
View Related
Jul 21, 2011
I have a ASA5510 and I have a question about the speed the ports can handle, here is one port:
-interface Ethernet0/2
- speed 100
-shutdown
- no nameif
-no security-level
-no ip address
it's ethernet and not fastethernet so I figure it will only go to 10Mbps, but at the same time I can hard code the speed to 100.
View 2 Replies
View Related
Feb 22, 2012
i have cisco ASA 5510 Firewall using in my network, i have planning to upgrade the Flash memory from 256 mb to 512 mb and the RAM from 256 mb to 1GB.
View 1 Replies
View Related
Feb 12, 2012
i am using Cisco ASA5510 Firewall in my Network in the distrubition Layer .Private Range of Network Address use in the Network and PAT at the FW for address translation.presently encountering an issue the users behind the FW in my network unable to RDP at port 2000 presented at the Client Network.Able to Telnet on port2000 but not RDP . any changes needed at the FW end to get the RDP Access.
View 12 Replies
View Related
Jun 6, 2012
ASA 5510 have two model Bun-K9 and Sec-Bun-K9 from the datasheet find out difference Port related and Redundancy. My questions is : Have any major difference for Security service between two model ?
View 3 Replies
View Related
Jun 13, 2012
I would like to know if is possible to configure a secondary IP address in a 5505 interface ??
View 1 Replies
View Related
Aug 27, 2012
We are in the process of implementing secondary ISP to our ASA firewall and We would like to run both ISPs in parallel so we can test until we finally cutover?
View 2 Replies
View Related
May 15, 2011
Can we assign Secondary ISP-2 Pool IP to DMZ Server, network design attached for reference.
View 2 Replies
View Related
Mar 3, 2013
I have two ASA 5520s in Active/Standby. I try and test this quartely to ensure it is working correctly. Everything works fine, except I have an issue with one interface. When doing a show failover, it shows the interface as failed on the secondary unit, and I am not sure why. It shows it as normal on the primary.
This host: Primary - Active
Active time: 9277305 (sec)
slot 0: ASA5520 hw/sw rev (2.0/8.2(4)) status (Up Sys)
Interface WaterworksCanopy (192.x.x.x): Normal
[code]....
View 15 Replies
View Related
Dec 5, 2011
We have 2 ASA 5505s in a data center at a remote site.
Whilst troubleshooting another issue I noticed the below. I don't know much about fail over but this would suggest that the secondary ASA is active and the primary ASA is on standby.
if the primary is "active" then how come the secondary is the active ASA? I would have thought that once the primary ASA became active this would assume the "main" role".
[Code] .....
View 7 Replies
View Related
Nov 24, 2012
We already have a subnet defined to inside interface and is in produciton. the default gateway is this interface ip. In that setup now I have to add one more subnet and as the first subnet is been defined in ASA indside interface, I have to assign secondary Ip to the inside interface so that new subnet users can easily reach here and go outside.
View 1 Replies
View Related
Jan 15, 2012
Cisco ASA 5505 Cannot Ping Secondary Internal Network.
View 9 Replies
View Related
Aug 17, 2011
As this is an ASA 5505, unlimited users, I must use arp alias to allow a secondary network.
Inside network: 10.200.31.0/24.Additional inside network: 10.200.12.0/24
Clients in both networks can reach internet, but they can't communicate with eachother. Hosts on the additional network can ping the ASA inside network IP, but nothing else. I get incomming hitcount for inside interface when 10.200.12.x tries to ping 10.200.31.x. In the error log, I see: [code]
View 7 Replies
View Related
Nov 20, 2011
I have a single production 5510 with 2 contexts. Now I want to integrate the secondary failover unit. My question is: How much configuration needs to be done on the secondary firewall? How much of the configuration will be sync'd from the primary to the secondary when the secondary is connected?
For example, do I need to add the following on the secondary or will it be sync'd from the primary?
admin-context NAME
context NAME
allocate-interface Ethernet0/0.14
[Code].....
View 3 Replies
View Related
Oct 14, 2012
I just purchased an ASA 5555 and started to configure. I was successful in natting all the IPs that are on the same subnet as the ASA eth0. I could not get the nat working for the 2nd address block.
Ex:
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 192.168.1.33 255.255.255.224
[Code]....
View 4 Replies
View Related
May 23, 2013
i never see this before, but on newly purchased just configured firewall.when i do wrtie standby.All interfaces on standby unit flaps.is it some IOS bug? my firewalls are [code] what could be the reason? FYI i am using LAN base failover and not doing any statful fail-over.
View 3 Replies
View Related
Nov 8, 2012
I have a working DMVPN solution. I am trying to stand up a secondary DMVPN hub at our disaster recovery site. We are trying to deply to a Dual HUB SIngle DMVPN solution. The HUB2 DMVPN router has an INSIDE trusted interface and has an OUTSIDE UNTRUSTED interface.
The inside is 10.248.11.X...the Untrust/public is 192.168.93.11 which is connected to our DMZ 3 on the ASA 5520.....then I am trying to NAT the 192.168.93.11 to an outside public IP 199.248.30.X....just not working...have had 2 tickets open with Cisco this week and they still are unable to resolve. I am sure it is the ASA5520 is not configured correctly.
View 1 Replies
View Related
Apr 10, 2012
i just received a RMA for failed ASA 5520 that was acting as secondary unit in multicontext configuration. What would be correct procedure to install it back in production? Do i need to restore backed up config of the fallen unit or is it just enough to enable multimode and connect to existing (primary) unit? Any good link for documentation that deal with this issues.
View 5 Replies
View Related
Feb 12, 2013
I have 4 public IPs on Router 3845 interface FastEthernet 0/0/1. IP as below.
50.200.2.2
50.200.2.3 secondary
50.200.2.4 secondary
50.200.2.5 secondary
I wan to allow ports 80 to 90 on 50.200.2.3 for my webserver (192.168.10.50)
View 5 Replies
View Related
Aug 25, 2011
Cisco ASA 5505 Security Plus 1 link with PPOE dialup for internet access
desirable situation: Primary link with a PPOE dialup Secondary Link with DHCP address Asignment
Problem: i want to configure Dual ISP Failover modus, but the problem exist when i configure the ip sla syntax it looks good in the running config. but after a reload the secondary line becomes primary
It looks like the ppoe client authentication is busy when the ip sla tracking mechanism becomes active. can i tweak the settings that the ip sla tracking mechanism starts later?
What i the correct config for Dual ISP setup with primary PPOE and secondary DHCP
View 1 Replies
View Related
Mar 14, 2011
We have to use scp on all of our network devices. It worked quite well on our routers and switches but I can't seem to get it to work for the firewalls and IPS. I enabled scp on my ASA5510 using the command "ssh scopy enable". I also ensured that a rsa key was generated and that ssh ver 2 was enabled. But I can't seem to locate the commands to actually have my firewall either copy it's configuration to a server or reach out to a server to pull down a file. We are using IOS 8.2(1).
View 1 Replies
View Related
Mar 22, 2011
I have a customer who wants to prioritze rdp traffic throgh the firewall.I know that its port 3389, but outgoing traffic is a random port number.Any smart way to catch this traffic and get it in the LLQ ?
View 3 Replies
View Related
Sep 13, 2012
we have ASA 5510 which we need to upgrade from 8.0(3) to 8.2.5. can we directly switch to 8.2.5 from 8.0(3) , if not what all versions we need to go from.
What all point needs to check before that following is show flash output.
97 14635008
Jan 01 2003 14:12:16 asa803-k8.bin 98 4096
May 14 2008 21:22:10 tmp 2 4096
Apr 20 2008 02:21:46 log 6 4096
Apr 20 2008 02:22:16 crypto_archive 99 6851212
[Code] .....
View 4 Replies
View Related
Sep 18, 2011
My device has 3 interfaces configured: inside, outside, DMZ. Right now I can access the DMZ from the Internet and I can access the DMZ from the LAN using an exempt nat statement. I am having a few issues setting up DMZ > LAN access however. The servers running on the DMZ need to send information to my LAN such as syslog traffic for example. Will DMZ traffic be NATed or should this somehow be excluded? Bascially all LAN devices should get to the DMZ devices by their actual IP and vice versa. Are there any special statements I need to add to the ASA such as nat or ACLs to make this work? My LAN is 10.10.6.0/24 and DMZ is 192.168.254.0/24.
View 1 Replies
View Related
Oct 20, 2011
I have a ASA 5510 with asa8.4(2) and asdm6.4(5)205. Have a new basic config, nothing special at this time. I just cannot seem to get from the inside to the outside. From the outside interface I can ping, so I have a good Internet connection. [code]
View 3 Replies
View Related
Apr 24, 2012
WE have a DMZ on ASA5510 8.4, it can access anything internal interface but cannot get out to internet or outside interface. I try to ping from a host in the DMZ to 8.8.8.8 and get this in the log 6Apr 25 201208:24:431100038.8.8.80172.10.1.1501Routing failed to locate next hop for ICMP from outside:8.8.8.8/0 to inside:172.10.1.150/1. [code]
View 14 Replies
View Related
Apr 5, 2012
I am having ASA5510 firewall which has 1GB RAM currently. I want to upgrade to 2GB. When I opened the box, I can see only 1 slot to insert the RAM. I searched in Cisco website and I got to know that I need to use 2 x 1 GB RAM. So, I need to have 2 slots to do that. But, I am having only 1 slot in the box.
View 5 Replies
View Related
Mar 30, 2011
We have an ASA5510 with a backup ISP connection protecting our corporate network. I also have a mail server and I would like to route SMTP traffic over the backup network. I realize that the ASA5510 does not support PBR, but I also know that I can use static NAT rules as a workaround to direct specific types of traffic over a particular interface (e.g. "static (outside,inside) tcp 0.0.0.0 www 0.0.0.0 www netmask 0.0.0.0" and "static (backup,inside) tcp 0.0.0.0 smtp 0.0.0.0 smtp netmask 0.0.0.0"). is it possible to use something similar to force a particular host to use a specific interface? I have tried to make this work on my own without success. Is it even possible?
View 5 Replies
View Related
